Livex Lighting Meridian 51085-91 Manual

Livex Lighting Lys Meridian 51085-91

Læs nedenfor 📖 manual på dansk for Livex Lighting Meridian 51085-91 (2 sider) i kategorien Lys. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
51052 51053 51054 51055 52133 52134 52135 52136 52141
52142 51042 51043 51044 51045 51082 51083 51084 51085
52140 52139 52151 52152 52153 52154 51362
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker box. Remove old fixture and all hardware
from Junction Box.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take
care not to lose any small parts necessary for installation.
3. Thread the two mounting screws about 1/4” into the pre-drilled holes in the
mounting plate spaced the same distance apart as the holes in the canopy (I).
4. Attach the mounting plate to the Junction Box with the two Junction Box Screws
as shown. The side of the mounting plate marked "GND" must face out. The
junction box is not included.
5. Attach the tube(B) to the top center pipe nipple of the shade(C), turn it until
tighten. Attach the canopy(I) to the tube(B), by turning it clockwise until tight.
NOTE: THE SHADE(C) OF THE PRODUCT MAY VARY.
,
6. Thread the pipe nipple (D) into the bottom center coupling of the lamp holder and
lock it securely with the hex nut.
7. Install the light bulbs(not included) in accordance with the fixture specifications.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
8. Raise the steel shim (E), glass (F) and plastic shim (G) to the bottom of the shade
(C), aligning the hole with pipe nipple and lock it securely with the finial (H).
9. While holding the shade assembly towards the ceiling, connect the electrical wires
as Shown in Fig.2, making sure that all wire nuts are secured. You may have to
wrap the connections with electrical tape. If your outlet has a ground wire (green
or bare copper), connect the fixture ground wire to it. Otherwise connect fixture’s
ground wire directly to the mounting plate with the green screw provided. After
wires are connected, tuck them carefully inside the Junction Box.
10. Raise the shade assembly onto the junction box, aligning screws on mounting
plate with mounting holes in canopy (I) and lock it securely with the ball nut (A).
Your installation is now complete. Return power to the junction
box and test the fixture.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black(Hot)
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or Bare
Copper(Ground)
`
Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly? Please call customer service at: 800-761-8056
Or visit us on-line at: WWW.LIVEXLIGHTING.COM
©COPYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC. DOC20161151052
FIG.2
FIG.1


Produkt Specifikationer

Mærke: Livex Lighting
Kategori: Lys
Model: Meridian 51085-91

Har du brug for hjælp?

Hvis du har brug for hjælp til Livex Lighting Meridian 51085-91 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Lys Livex Lighting Manualer

Lys Manualer

Nyeste Lys Manualer

Nicols

Nicols BSW 10R Manual

23 November 2024
Nicols

Nicols BSW 200 LED Manual

22 November 2024
Aputure

Aputure LS 600C Pro Manual

19 November 2024
Neno

Neno Titto Manual

19 November 2024
V-TAC

V-TAC VT-25W Manual

18 November 2024
Yongnuo

Yongnuo YN508 Manual

17 November 2024