LYYT LT245120-NW Manual

LYYT Ikke kategoriseret LT245120-NW

Læs nedenfor 📖 manual på dansk for LYYT LT245120-NW (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
HIGH OUTPUT LED TAPE
Installation Guide
V2 .0
Caution: Please read this guide carefully before installing Lyyt LED tape
Damage caused by incorrect application is not covered by the warranty
Installation
Lyyt high output LED tape is supplied on 5m reels and operates from a 24Vdc power supply.
Installation should be carried out by competent electrical installers, observing the relevant electrical safety procedures.
The tape has a self-adhesive backing to allow it to be easily attached to a clean, non-porous surface.
Where less than 5m of tape is needed, there are solder points as shown below, where the tape may be cut to size. These
cut points will be at 5cm intervals. In order to re-connect to another length of tape after cutting, strip away the epoxy
coating at the solder points and solder a wire from “+” to “+” and a wire from “ ” to “ ” as shown below. - -
Some accessories are supplied with the tape reel for this purpose or alternatively, connection clips may also be used Lyyt
to join lengths of tape (156.135UK 156.140UK). In order to retain weather-proofing, it is advised to seal the cuts and
joints with silicone glue.
Each 5m reel of single colour LED tape is fitted with a 2.1mm DC jack socket for power input for easy connection to a
power supply. This connector may be removed and stripped for bare wire connection if a 2.1mm jack is not fitted to the
power supply.
If the power supply has enough capacity to power more than one reel, another reel can be connected to the end of the
first reel via the 2.1mm DC jack plug.
For Lyyt high output LED tape, it is recommended to link no more than 15m of tape in sequence .
Using a separate wire to loop “+” and “ ” back to the power supply will help to avoid dimming at the far end through -
voltage drop.
To connect beyond these lengths, a parallel wire must be run from the power supply to the further reels of tape.


Produkt Specifikationer

Mærke: LYYT
Kategori: Ikke kategoriseret
Model: LT245120-NW

Har du brug for hjælp?

Hvis du har brug for hjælp til LYYT LT245120-NW stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret LYYT Manualer

LYYT

LYYT CLIP10-B Manual

29 August 2024
LYYT

LYYT DIY-CW60 Manual

20 August 2024
LYYT

LYYT PS30-24 Manual

17 August 2024
LYYT

LYYT LT24560-BL Manual

16 August 2024
LYYT

LYYT DIY-B60 Manual

15 August 2024
LYYT

LYYT DIYH-RGB30 Manual

14 August 2024
LYYT

LYYT LT12560-WW Manual

14 August 2024
LYYT

LYYT PS40 Manual

14 August 2024
LYYT

LYYT RGB10-F Manual

14 August 2024
LYYT

LYYT LT12560-CW Manual

14 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024