Martin CX-10 Extreme Manual

Martin Ikke kategoriseret CX-10 Extreme

Læs nedenfor 📖 manual på dansk for Martin CX-10 Extreme (41 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 21 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/41

CX-10 Extreme

user manual

217

217217

109

109109 340

340

340340

412

412412

reproduced, in any form or by any means, without

permission in writing from Martin Professional A/S,

Denmark.

Printed in Denmark.

P/N 35000129,Rev. C

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features .................................................................................................................................................4

About this manual ...................................................................................................................................4

Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety precautions ..................................................................................................................................5

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Unpacking ..............................................................................................................................................6

AC power ................................................................................................................................................6

Installation ..............................................................................................................................................7

Connecting the serial data link ...............................................................................................................8

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Menu navigation .............................................................................. ....................... ...............................9

Address selection ...................................................................................................................................9

Tailoring performance ..........................................................................................................................10

Information readouts ............................................................................................................................10

Test and service utilities .......................................................................................................................11

DMX-512 control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Lamp power ..........................................................................................................................................13

Effect position .......................................................................................................................................13

Speed control .......................................................................................................................................14

Optical configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Effect wheel ..........................................................................................................................................15

Color filters ...........................................................................................................................................18

Optional lenses .....................................................................................................................................19

Animation wheels .................................................................................................................................22

Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Lamp ....................................................................................................................................................28

Cleaning ...............................................................................................................................................29

Lubrication ............................................................................................................................................30

Replacing fuses ....................................................................................................................................30

Updating software ................................................................................................................................31

DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Control menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

PCB connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Specifications - CX-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

4 CX-10

NTRODUCTION

Features

Thank you for selecting the Martin CX-10 Extreme. Some of the many features include:

• efficient, 3000 hour, 250 watt discharge lamp

• 12 interchangeable dichroic colors plus open

• double-sided, 13-position, effect wheel which enables overlapping effects.

• motorized focus

• full-range dimming

• fast blackout and strobe effects

• coated optics

• switch-selectable power supply settings

• integrated mounting bracket

• easy-to-clean cooling fan

• optional wide and narrow angle lens kits available

• optional animation kit available

About this manual

Please check the Martin web site at http://www.martin.com for the latest product software and

documentation.

Comments or suggestions regarding this document may be e-mailed to service@martin.com or sent by

standard mail to:

Martin Professional A/S

Olof Palmes Allé 18

DK-8200 Aarhus N, Denmark

Attn: Service Department

Please review the important safety precautions in this manual before installing and operating the fixture.

Safety 5

AFETY

Warning! This product is for professional use only. It is not for household use.

This product presents risks of lethal or severe injury due to fire and heat, electric shock, ultraviolet radiation,

lamp explosion, and falls. Read this manual before powering or installing the fixture, follow the safety

precautions listed below and observe all warnings in this manual and printed on the fixture. If you have

questions about how to operate the fixture safely, please contact your Martin dealer or call the Martin

24-hour service hot line at +45 70 200 201.

Safety precautions

P R O T E C T I O N F R O M E L E C T R I C S H O C K

• Disconnect the fixture from AC power before removing or installing the lamp, fuses, or any part, and when

not in use.

• Always ground (earth) the fixture electrically.

• Use only a source of AC power that complies with local building and electrical codes and has both overload

and ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Refer any service operation not described in this manual to a qualified technician.

P R O T E C T I O N F R O M U V R A D I A T I O N A N D L A M P E X P L O S I O N

• Never operate the fixture with missing or damaged lenses and/or covers.

• When replacing the lamp, allow the fixture to cool for at least 15 minutes before opening the fixture or

removing the lamp. Protect your hands and eyes with gloves and safety glasses.

• Do not stare directly into the light. Never look at an exposed lamp while it is lit.

• Replace the lamp if it becomes defective or worn out, or before usage exceeds the maximum service life.

P R O T E C T I O N F R O M B U R N S A N D F I R E

• Never attempt to bypass the thermostatic switch or fuses. Always replace defective fuses with ones of the

specified type and rating.

• Keep all combustible materials (for example fabric, wood, paper) at least 0.1 meter (4 inches) away from the

fixture. Keep flammable materials well away from the fixture.

• Do not illuminate surfaces within 0.3 meters (12 inches) of the fixture.

• Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.

• Never place filters or other materials over the lens.

• The exterior of the fixture can get very hot. Allow the fixture to cool for at least 5 minutes before handling.

• Do not modify the fixture or install other than genuine Martin parts.

• Do not operate the fixture if the ambient temperature (T

a) exceeds 40° C (104° F).

P R O T E C T I O N F R O M I N J U R Y D U E T O F A L L S

• When suspending the fixture, verify that the structure can hold at least 10 times the weight of all installed

devices.

• Verify that all external covers and rigging hardware are securely fastened and use an approved means of

secondary attachment such as a safety cable.

• Block access below the work area whenever installing or removing the fixture.

6 CX-10

ETUP

Unpacking

The CX-10 comes with:

• MSD 250/2 lamp

• 3-meter, 3-wire IEC power cable

• user manual

The packing material is carefully designed to protect the fixture during shipment - always use it or a custom

flight case to transport the fixture.

AC power

Warning! For protection from electric shock, the fixture must be grounded (earthed). The power

supply shall have overload and ground-fault protection.

Important! Verify that power supply settings match the local AC supply before use.

The CX-10 is factory configured for 230 V / 50 Hz operation. If your AC power supply is

different, the fixture must be configured for the local voltage and frequency. Always use

the voltage settings that are equal to or next highest to your AC supply.

C O N F I G U R I N G F O R L O C A L A C P O W E R

1 Disconnect the fixture from power.

2 Remove the 4 cover screws and lift off the front cover.

3 Locate the selection switches and the settings label, which is by the color wheel. Move the voltage switch to

the setting that is equal to or higher than the local AC voltage. If your voltage falls between 2 settings,

always select the higher voltage. For example, if the AC voltage is 215 V, use the 230 V setting instead of

210 V.

4 Move the frequency switch to the setting that matches the local AC frequency: 50 or 60 Hz.

5 Replace the cover.

Frequency

Voltage

Setup 7

I N S T A L L I N G A P L U G O N T H E P O W E R C A B L E

The power cable must be fitted with a grounding-type cord cap that fits your power distribution system.

Consult an electrician if you have any doubts about proper installation.

• Following the cord cap manufacturer’s instructions, connect the yellow and green wire to ground (earth), the

brown wire to live, and the blue wire to neutral. The table below shows some pin identification schemes.

A P P L Y I N G P O W E R

Warning! The power cables must be undamaged and

rated for the electrical requirements of all

connected devices.

Important! Powering through a dimmer system can

damage the fixture.

1 Verify that the supply cable is undamaged and rated

for the current requirements of all connected devices.

2 Plug the prepared power cable into the AC socket and

a grounded AC power supply.

Installation

L O C A T I O N A N D O R I E N T A T I O N

The CX-10 may be installed in any orientation. It can be fastened directly to a suitable surface, hung with a

rigging clamp, or placed directly on a level surface.

For safe operation, install the CX-10 in a location where

• the fixture is at least 0.1 meters (4 inches) away from combustible materials

• the fixture is protected from rain and moisture

• there is at least 0.1 meters (4 inches) clearance around the fan and control panel

• there are no flammable materials nearby

R I G G I N G O R M O U N T I N G T H E C X - 1 0

Warning! Block access below the work area before proceeding.

Warning! Always use a secure means of secondary attachment.

1 If using a rigging clamp (not included), verify that it is undamaged and can bear at least 10 times the fixture’s

weight. Bolt the clamp securely to the bracket with a grade 8.8 (minimum) M12 bolt and lock nut, or as

recommended by the clamp manufacturer, through the 13 mm hole in the center of the mounting bracket.

2 If fastening the fixture directly, verify that the hardware (not included) and mounting surface can bear at least

10 times the fixture’s weight. The four 6.2 mm holes and/or the 13 mm hole in the mounting bracket may be

used to fasten the fixtures.

3 Verify that the structure can support at least 10 times the weight of all installed fixtures, clamps, cables,

auxiliary equipment, etc.

4 Working from a stable platform, clamp or fasten the fixture to the structure.

Wire Pin Marking Screw color

brown live “L” yellow or brass

blue neutral “N” silver

yellow/green ground green

Table 1: Plug wiring

AC input & fuse holder

Data input

Data output

8 CX-10

5 Install a safety cable that can hold at least 10 times the weight of the fixture through/over the support and

anywhere through the fixture’s aluminum frame.

6 Loosen the swivel locks and tilt the fixture to the desired angle. Turn the swivel locks clockwise to tighten.

When a handle reaches its limit, pull it out, turn counterclockwise, release, and continue tightening.

7 Verify that the fixture meets the location requirements listed previously.

Connecting the serial data link

The CX-10 has locking 3-pin data input and output sockets that are wired for use with DMX devices

with pin 1 to shield, pin 2 to cold (-) and pin 3 to hot (+). As some devices have 5-pin connectors, or 3-pin

connectors with reversed polarity on pins 2 and 3, the following adaptor cables may be required.

1 Connect the controller’s output to the fixture’s data

input. For a DMX controller with 5-pin output, use a

cable with a 5-pin male and a 3-pin female XLR

connector.

2 Connect the output of the fixture closest to the

controller to the input of the next fixture. If connecting a

fixture with pin 3 hot to a fixture with pin 3 cold, use a

phase-reversing adaptor.

3 To terminate the link, insert a male 120 ΩXLR

termination plug in the output of the last fixture.

T I P S F O R B U I L D I N G A S E R I A L L I N K

• Use shielded twisted-pair cable designed for RS-485

devices: standard microphone cable cannot transmit DMX data reliably over long runs. For links up to 300

meters (1000 ft.) long, you can use 24 AWG, low capacitance, 85-150 ohm characteristic impedance,

shielded cable with 1 or more twisted pairs. For runs up to 500 meters (1640 ft.) use 22 AWG cable. Use an

amplifier if the serial link exceeds 500 meters.

• Never use a “Y” connector to split the link. To split the serial link into branches use a splitter such as the

Martin 4-Channel Opto-Isolated RS-485 Splitter/Amplifier.

• Do not overload the link. Up to 32 devices may be connected on a serial link.

• Terminate the link by installing a termination plug in the output socket of the last fixture on the link. The

termination plug, which is simply a male XLR connector with a 120 ohm, 0.25 watt resistor soldered

between pins 2 and 3, “soaks up” the control signal so it does not reflect back down the link and cause

interference. If a splitter is used, terminate each branch of the link.

Phase-Reversing

Adaptor

Male Female

3-pin to 3-pin

P/N 11820006

Adaptor

Male Female

5-pin to 3-pin

P/N 11820005

Adaptor

Male Female

3-pin to 5-pin

P/N 11820004

Figure 1: Cable adaptors

AC input & fuse holder

Data input

Data output

Control Panel 9

ONTROL

ANEL

You set the address and personalities, read out data, and execute service utilities from the control panel.

Settings can also be changed remotely via the serial link with the Martin MP-2 uploader.

There are four small symbols that can appear in the control panel display:

Menu navigation

See also the control menu table starting on page 34.

The DMX address and any error messages are displayed after the fixture resets. To enter the menu, press

[menu]. Use the [up] and [down] keys to move within the menu. To select a function or submenu, press

[enter]. To escape a function or menu, press [menu].

Address selection

The CX-10 requires 10 channels for DMX control. The address, also known as the start channel, is the first

channel used to receive instructions from the controller. For independent control, each fixture must be

assigned its own address and non-overlapping control channels. Two CX-10s can share the same address

Power is on and the fixture is ready.

The fixture is writing to memory. Do not power off the fixture while this symbol is

lit.

The fixture is receiving DMX.

Error. See “Error messages” on page 37 and “Troubleshooting” on page 38.

AddR dMXL UTIL

Address/

Messages

STCO

SHUT

....

EFSP

AdJ

PCbT

UPLd

TSEQPERS dFSE INFO

SCUT

dISP

dINT

dLOF

ALON

FACT

CAL

dFOF

TIME

HRS

L HR

L ST

VERdRES

RST

L ON

LoFF

EFCT

SHUT

dIM

COL

FOC

RATE

qUAL

MAN

RUN

WHEL

10 CX-10

if they are to respond identically: they will receive the same instructions and individual control will not be

possible.

T O S E T T H E D M X A D D R E S S

1 Apply power to the CX-10. Press [menu] to enter the main menu.

2 Select AddR using the [up] and [down] keys. Press [enter].

3 Select an address (start channel) from 1 to 502 using the [up] and [down] keys. Press [enter]. Press [menu]

to return to the main menu.

Tailoring performance

M O V E M E N T

S C U T, the shortcuts setting, determines whether the color and gobo wheels scroll past open when

changing positions. When set to O N , the wheels can “take a shortcut” and scroll through open when this is

the shortest path to the next position. The wheels do not scroll past open when S C U T is set to OFF.

D I S P L A Y

The display menu (PERS>dISP) determines whether the display remains lit or not. Select O N to have

the display remain lit, or OFF to extinguish the display two minutes after the last key press.

To flip the display for easier reading, press [up] and [down] simultaneously.

The display intensity setting (P E R S > d I N T ) controls display brightness. You can select A U T O for

automatic dimming of the display using the built-in light sensor, or manually select an intensity level from 10

to 100.

L A M P P O W E R

There are two settings that modify lamp control: Automatic Lamp On (P E R S > AL O N ) and DMX Lamp-Off

(P E R S > D L o F ).

There are three options for automatic lamp control: O N , O F F, and D M X . When ALON is OFF, the lamp

remains off until a lamp-on command is received from the controller. When A L O N O N is , the lamp strikes

automatically after the fixture is powered on. When ALON is set to DMX, the lamp strikes automatically

when the fixture receives DMX data, and it extinguishes automatically 15 minutes after DMX data is lost.

When ALON is either ON or DMX, lamp strike timing is determined by the fixture address to prevent all

lamps from striking at once.

The DMX Lamp-Off setting effects how the lamp can be turned off. When d L O F is O N , lamp power can be

switched off by sending a DMX value from 248 to 255 on channel 1 for five seconds. When dLOF OFF is ,

the lamp-off command will not work unless special conditions are met. Refer to the DMX protocol.

RESET

The fixture can be reset from the controller if DMX reset (P E R S > d R E S ) is O N . If DMX reset is OFF, this

command will not work unless special conditions are met. Refer to the DMX protocol.

D E F A U L T S E T T I N G S

The fixture can be reset to its factory default settings by selecting d F S E > F A C T > L O A d .

Information readouts

P O W E R - O N H O U R S

Read the total number of hours the fixture has been on since fabrication (I N F O > T IM E > H R S > T O T L ),

and the number of hours on since the counter was last reset (I N F O > T I M E > H R S > R S E T ). This can be

used to track maintenance intervals. Press [up] for 5 seconds while displayed to reset.

Control Panel 11

L A M P H O U R S

Read the total number of lamp hours since fabrication (I N F O > T I M E > L H R > T O TL ), and the number

of lamp hours since the counter was last reset (I N F O > T I M E >L H R> R S E T ). Reset this counter after

installing a new lamp. Press [up] for 5 seconds while displayed to reset.

L A M P S T R I K E S

Read the total number of lamp strikes (I N F O > T I M E > L S T >T O T L ), and the number of lamps strikes

since the counter was last reset (INFO>TIME>L ST>RSET). Reset this counter when installing a

new lamp. Press [up] for 5 seconds while displayed to reset.

F I R M W A R E V E R S I O N

I N F O > V E R displays the firmware version number. The firmware version is also displayed briefly at

startup.

Test and service utilities

D M X R E A D O U T

The DMX log (d M X L ) menu provides useful information for troubleshooting control problems.

R A T E displays the DMX refresh rate in packets per second. Values lower than 10 or higher than 44 may

result in erratic performance, especially when using tracking control.

QUAL displays the quality of the received DMX data as a percentage of packets received. Values much

below 100 indicate interference, poor connections, or other problems with the serial data link that are the

most common cause of control problems.

S T C O displays the DMX start code. Packets with a start code other than 0 may cause irregular

performance.

The remaining options under d M X L display the DMX values received on each of the channels, from S H U T

(shutter, channel 1) to E F S P (effect speed, channel 10). If the fixture does not behave as expected,

reading the DMX values can help you troubleshoot the problem.

M A N U A L C O N T R O L

The manual control menu (MAN) provides commands for turning the lamp on (LON), turning the lamp off

(LoFF RST), and resetting the fixture ( ). It also permits you to position and move individual effects.

E F F E C T S T E S T

The test sequence (T S E Q > R U N ) runs through all effects to provide a quick check of fixture performance.

Note: the test sequence does not automatically strike the lamp. Use M A N > L O N M A N > L o F F and to

control lamp power. Press [menu] to stop the test.

A D J U S T M E N T P O S I T I O N S

The adjustment menu (U T I L > A d J ) provides commands for positioning effects during mechanical

adjustment.

E F F E C T C A L I B R A T I O N

With the calibration menu (U T I L > C A L ), effect positions can be fine-tuned with a software-defined offset

value to compensate for small misalignments or differences between fixtures.

The default offset command (U T I L > d F O F ) erases any offsets stored in memory.

C I R C U I T B O A R D T E S T

U T I L > P C B T executes a routine designed for testing the main circuit board. For service use only.

12 CX-10

U P L O A D M O D E

The upload mode command (U T I L > U P L d ) prepares the fixture for a software update. This command is

not necessary, however, as upload mode is engaged automatically by the uploader.

DMX-512 control 13

DMX-512

CONTROL

This section briefly describes the DMX-controllable effects. See also the DMX table starting on page 32 and

the DMX chart on the back cover.

Lamp power

L A M P - O N

Unless automatic lamp strike is enabled, lamp power remains off until a lamp-on command is sent from the

controller.

Note: A peak of electric current that can be many times the operating current is drawn for an instant when

striking a discharge lamp. Striking many lamps at once may cause a voltage drop large enough to prevent

lamps from striking or draw enough current to trip circuit breakers. If sending lamp-on commands to multiple

fixtures, program a sequence that strikes lamps one at a time at 5 second intervals.

L A M P - O F F

The lamp can be turned off from the controller by sending the lamp-off command on channel 1 for 5

seconds. The lamp cannot be restruck for 8 minutes after being turned off. Note that the

lamp-off command may be disabled by the DMX Lamp-Off personality setting.

Effect position

RESET

If an effect loses its indexing and fails to move to programmed positions, the fixture can be reset from the

controller by sending the “Reset” command on channel 1 for 5 seconds. Note that the DMX reset feature

may be disabled by the DMX Reset personality setting.

D I M M E R / S H U T T E R

The mechanical dimmer/shutter system provides full, high-resolution dimming, “instant” open and blackout,

random and variable strobe effects, and random and variable pulses in which the dimmer snaps open and

slowly dims or snaps closed and slowly opens. Shutter, strobe, and pulse effects are selected on channel 1.

The intensity level is selected on channel 2.

C O L O R

The 13 color wheel positions can be selected on channel 3. The color wheel can be scrolled continuously -

allowing for split color effects - or in steps, and rotated randomly or continuously in both directions at

different speeds (set on channel 5).

E F F E C T W H E E L

The 13 positions on the effect wheel can be selected on channel 4.

The effect wheel also rotates continuously in both directions at variable speed (set on channel 6).

F R O S T F I L T E R

The frost filter is selected on channel 7.

F O C U S

The beam may be focused from approximately 2 meters (6.5 feet) to infinity using channel 8.

14 CX-10

Speed control

T R A C K I N G C O N T R O L

Tracking control is enabled by setting the Effects speed channel (10) to 0.

With tracking control, the speed at which effects move is determined by the cross-fade time between two

positions or scenes. The controller divides the move into steps and updates the fixture with small changes

at the rate required to achieve the fade. The fixture “tracks” the changes and averages them with a digital

filter algorithm to provide smooth movement.

V E C T O R C O N T R O L

With vector control, movement speed is determined by the speed values on channel 10. This provides a way

to control speed on controllers without cross-faders. Vector control also provides smoother movement,

particularly at slow speeds, with controllers that send slow or irregular tracking updates.

When using vector control, the cross-fade time must be 0.

B L A C K O U T

When “blackout while moving” is selected on channel 10, the shutter closes when the effect moves to make

the transition invisible. The shutter opens when the movement is complete.

P E R S O N A L I T Y O V E R R I D E S

Channel 10 provides tracking values that allow you to override the shortcuts setting. See the DMX table for

details.

Optical configuration 15

PTICAL

CONFIGURATION

This chapter contains the following sections:

• Effect wheel

• “Color filters” on page 18

• “Optional lenses” on page 19

• “Animation wheels” on page 22

Effect wheel

The CX-10 contains a double-sided effect wheel which enables two effects to be combined at each of the 13

positions. This enables gobos and other effects to be combined. Effects are mounted on effect flags.

Effects that require a sharp focus should be placed on the lamp side of the effect wheel.

S T A N D A R D E F F E C T W H E E L C O N F I G U R A T I O N S

1313

1212

1111

1010

55 4

44 3

Front-lens-side effect wheel positions

5 6

8 10 12 13

16 CX-10

Position Lamp-side effect wheel Front-lens-side effect wheel Combined effect

1 Open gobo, +22,5/17 HT-painted

2 Gobo with 12 mm hole

3 Gobo with 8 mm hole

4 Gobo with 4 mm hole

5 Forrest Floor Small arctic textured glass

6 Concrete flag textured glass Punched twinkle A "Golf balls" effect

7 Leaf breakup

8 Fibroid textured glass Punched twinkle B "Fibroid twinkle"

9 Linear break-up

10 Punched rectangular. effect Large textured glass "Bamboo" effect

11 Cell breakup

12 Limbo flag textured glass Punched aperture 18 mm

13 Open gobo, +22,5/17 HT-painted Color temperature correction 5500-2900K

1313

1212

1111 10

1010

22 123

4 5 6

9 10 11 12 13

Lamp-side effect wheel positions

Optical configuration 17

R E P L A C I N G A N E F F E C T F L A G

1 Disconnect the fixture from AC power and allow it to cool.

2 Remove the cover.

3 Turn the effect wheel to access the desired position. Press the effect flag

forwards slightly to release it and then grasp it by the edges and remove.

4 To insert an effect flag, slide it under the retention spring until it snaps into

place.

5 Replace the cover before applying power.

G O B O O R I E N T A T I O N

Figure 2 shows the correct orientation for different gobo types. When in doubt, install gobos with the more

reflective side towards the lamp.

Coated Glass Gobos

Uncoated side towards stageCoated side towards lamp

When an object is held up to the

coated side there is no space between

the object and its reflection. The back

edge of the gobo cannot be seen

when looking through the coated side.

When an object is held up to the

uncoated side there is a space between

the object and its reflection. The back

edge of the gobo can be seen when

looking through the uncoated side.

Textured side towards wheel

Textured Glass Gobos

Smooth side away from wheel

Metal Gobos

Reflective side towards lamp Black side towards stage

Image/text Gobos

Reversed image towards lamp True image towards stage

Figure 2: Gobo orientation

18 CX-10

Color filters

S T A N D A R D C O N F I G U R A T I O N

The CX-10 provides 12 dichroic color filters as shown below.

R E P L A C I N G A C O L O R F I L T E R

1 Disconnect the fixture from AC power and allow it to cool.

2 Remove the fixture cover.

3 Turn the color wheel to access the desired color filter. Press the filter

forwards slightly to release it and then grasp it by the edges and remove.

4 To insert a filter, slide it under the retention spring until it snaps into place.

5 Replace the fixture cover.

55 6

1010

1111

1212

1313

Position Color

1 Open

2 UV transmitter

3 Yellow 603

4 Blue 104

5 Pink 312

6 Green 206

7 Blue 108

8 Red 301

9 Magenta 507

10 Blue 101

11 Orange 306

12 Dark green

13 Purple 502

Figure 5: CX-10 color wheel

Optical configuration 19

Optional lenses

The standard 22 degree lens can be changed to 14 or 32 degrees using two separately orderable lens kits.

See Accessories on page 41 for part numbers.

C H A N G I N G T H E L E N S

1 Disconnect the fixture from AC power and allow it to cool.

2 Remove the fixture cover.

3 Using a Phillips screwdriver, remove the focus module.

4 Using a Phillips screwdriver, remove the two screws from the focus module that hold the lens assembly in

place.

5 Slide the lens assembly out of the focus module.

6 Slide the replacement lens assembly in to the focus module and secure it using the two Phillips screws.

7 If you are installing the narrow-angle lens kit (14° beam angle) then you need to change the glass. Remove

the dimmer module so that you can access the front glass module. Remove the front glass module and

20 CX-10

replace the standard front glass with the glass lens supplied in the narrow-angle lens kit. Replace the front

glass module.

8 Ensure that the dimmer module is installed in the appropriate position.

Dimmer module Front glass module Front glass replacement

Wide angle lens position

Standard and narrow

angle lens position

Dimmer module

Optical configuration 21

9 Using a Phillips screwdriver, replace the focus module.

10 Replace the fixture cover before applying power.

22 CX-10

Animation wheels

An animation wheel can replace, or be affixed to the color wheel. This requires an Animation Wheel Adaptor

Kit and an animation disc (see “Accessories” on page 41).

For a list of currently available animation wheels and tips on what effects are possible, see “Animation

wheels and their uses” below. To achieve many effects you will use both an animation wheel and a regular

gobo (and potentially a color filter) installed on the effect wheel.

To install an animation wheel, see:

• “Affixing an animation wheel to the color wheel” on page 24, below, or

• “Replacing the color wheel with an animation wheel” on page 26

A N I M A T I O N W H E E L S A N D T H E I R U S E S

The animation wheels mentioned here can be ordered from your Martin dealer. The effects described are

merely suggestions and a degree of experimentation may be required to achieve exactly the effect that you

want to achieve. You may need to align the whole fixture along another plane in order to achieve animated

vertical or horizontal motion.

Tangential breakup: Th e Tan gential Breaku p disc (P/N 624002 1 5 )

produces a subtle rippling motion, particularly when moving parallel with the

lines of the gobo. It is the most suitable for rising flames, flowing water and

other effects where a single direction of movement is required.

Radial breakup: The Radial Breakup disc (P/N 62400211) is perfect for

providing a strong regular movement suitable for flickering flames, water

ripples, reflected water and shimmers for heat haze or mirage effects.

Spiral breakup: The Spiral Breakup disc (P/N 62400216) pattern is very

similar to the Radial Breakup disc, but has some movement at right angles

to the main motion, as is seen in wind blown rain, snow, or flames. It is

particularly worth experimenting with the angle of the gobo and the

orientation of the fixture to achieve all the possibilities with this pattern.

Optical configuration 23

Linear breakup: The Linear Breakup disc (P/N 62400223) provides

rhythmic movement and can be used to simulate a breeze through the

branches of a tree or the rhythmic undulations of sea waves.

Triangle breakup: The Triangle Breakup disc (P/N 62400225) gives a more

pronounced and rapid rhythmic effect than the Linear Breakup disc, and is

suitable for use as psychedelic effects or for a rough sea effect.

Cloud breakup: The Cloud Breakup disc (P/N 62400213) is designed for a

softer directional movement particularly at slow or very slow speeds. It is

suitable for cloud effects with cloud gobos or for a soft slow-flowing stream

effect.

Elliptical breakup: The Elliptical Breakup disc (P/N 62400221) produces a

bidirectional movement similar to the Spiral Breakup, but with constantly

changing direction of movement. This is specifically useful for snow or

similar effects where flurries of movement would be expected.

Dot breakup: The Dot Breakup disc (P/N 62400214) gives you the

opportunity to cause motion while maintaining a more focused projection of

the gobo image. It is suggested for effects such as falling leaves or rising

bubbles.

DHA 14

DHA 15

DHA 17

24 CX-10

Flicker wheel: The Flicker Wheel (P/N 62400222) provides a different kind

of effect and can be used at high speed for motion effects, such as passing

trains. It can also be effectively used for just breaking up the beam of a

fixture and for an organic strobe effect.

Coarse radial breakup: The Coarse Radial Breakup disc (P/N 62400224)

is particularly effective for animating light from a non-focused source whilst

providing a minimal loss in intensity due to the high 'white to black' ratio of

the radial pattern. It is also effective for similar uses to the Radial Breakup

disc.

Coarse tangential breakup: The Coarse Tangential Breakup disc (P/N

62400226) can be used on its own in an unfocused form to give the image

of flames. It can also be combined with gobos to give a drifting image to the

projection.

A F F I X I N G A N A N I M A T I O N W H E E L T O T H E C O L O R W H E E L

To affix an animation wheel to the color wheel:

1 Using the control menu (see “Control menu” on page 34), select the wheel (WHEL) personality (under the

PERS menu) and set it to EFCT. If you fail to do this an error will occur when the fixture resets.

2 Disconnect the fixture from AC power and allow it to cool.

3 Remove the fixture cover.

4 Using a Phillips screwdriver, remove the effect wheel module.

DHA 19

DHA 20

DHA 21

Optical configuration 25

5 Remove the effects wheel and then the color wheel using a 2.5 mm hex wrench.

The wheels are held in place using clamps that are similar to the one illustrated

here.

6 Bearing in mind that in this configuration the animation wheel and the color wheel

will rotate constantly, remove or replace any color flags as appropriate to the

effect that you want to achieve. Note that you can move color flags to the effect

wheel if necessary.

7 Modify the color wheel with the parts supplied in the Animation Wheel Kit as

shown in the following illustration.

8 Place the animation wheel on the color wheel. It is held in place magnetically.

9 Place the combined color/animation wheel back on the motor spindle with the animation wheel closest to

the lamp/effect motor. Ensure that the animation wheel is as close as possible to the effect-wheel-module

bulkhead without it coming in contact with anything that might hinder its free rotation. The closer the

animation wheel is to the bulkhead, the sharper you will be able to focus on it. Clamp the color wheel into

place using a 2.5 mm hex wrench.

10 Replace the effects wheel, ensuring that it will sit as close to the focus module as possible. The optimal

distance from the effects module bulkhead to the effect wheel is 15 mm (0.6 in.), but ensure that the wheel

does not come into contact with anything that might hinder its free rotation. Clamp the effects wheel into

place using a 2.5 mm hex wrench.

11 Replace the effect wheels module.

12 Replace the fixture cover before powering the fixture on.

13 If the effect wheel needs to be recalibrated, use the use the control menu to select UTIL>CAL>GoOf,

where you can fine-tine the effect wheel position with a software-defined offset

Produkt Specifikationer

Mærke:	Martin
Kategori:	Ikke kategoriseret
Model:	CX-10 Extreme

Har du brug for hjælp?

Hvis du har brug for hjælp til Martin CX-10 Extreme stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Martin Manualer

Martin Exterior Dot-1 Pro Manual

25 September 2024

Martin Exterior Dot-9 Pro Manual

25 September 2024

Martin DCE PSU 240 IP Manual

24 September 2024

Martin P3 PowerPort 500 IP Rental Manual

24 September 2024

Martin DCE Data Splitter/Booster IP Manual

23 September 2024

Martin P3 PowerPort 2000 Manual

23 September 2024

Martin P3 PowerPort 500 IP Install Manual

23 September 2024

Martin ZR20 MKII Manual

3 September 2024

Martin The Wife UPdater Manual

3 September 2024

Martin 2510 Controller Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterpik WP-490 Manual

10 April 2025

Daikin EAVX16S18DA9WG Manual

10 April 2025

Daikin RXYLQ40T7Y1B Manual

10 April 2025

Daikin RXYLQ42T7Y1B Manual

10 April 2025

Daikin ETVZ16S23EA6V7 Manual

10 April 2025

Daikin FXMA200AXVMB Manual

10 April 2025

Daikin FXZQ15A2VEB Manual

10 April 2025

Daikin ETVZ16S18EA9W Manual

9 April 2025

Daikin DSR1 Manual

9 April 2025

Simplified MFG SP18CAT120 Manual

9 April 2025