Meliconi Speedy 2.1 Manual

Meliconi Fjernbetjening Speedy 2.1

Læs gratis den danske manual til Meliconi Speedy 2.1 (4 sider) i kategorien Fjernbetjening. Denne vejledning er vurderet som hjælpsom af 59 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 30 anmeldelser. Har du et spørgsmål om Meliconi Speedy 2.1, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Speedy 2.1
Thank you for choosing a Meliconi remote control.
The Speedy 2.1 remote control is designed to command and a DECODER (satellite or digital terrestriala TV ).
IMPORTANT! When the remote control is set to control only device (example: TV), all the buttons will control that one
device; whilst when it is set to control 2 devices (TV + DECODER), e buttons will control the TV, only th V+ V-
whilst the other buttons will control the DECODER.
Speedy 2.1 is a simplied remote control; it provides ONLY the functions on the keypad.
The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio
frequency (e.g. voice commands and pointers) are not supported.
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
The remote control requires 2 new 1.5V alkaline batteries, not included in the AAA/LR03
package. Insert with the correct polarity as shown in gure.
DO NOT use batteries. rechargeable
BATTERIES TEST: Press and hold the 5 button and check that the LED remains on
continuously until the button is released. If the light is o or blinks, the inserted batteries are low,
therefore they need replacement.
WARNING:
As the remote control is capable of controlling 2 devices, during setup you must select the operation mode then dene which ;
device you want to control. (TV / STB)
To select the operation mode, press the button quickly and repeatedly until the LED corresponding to
the device you want to operate is switched on. ( led / led) TV = red STB = green
Before using the remote control, for each device you wish to control, it is to set a it matched. essential specic code,
Identify the specic code and set it into the remote control using one of the following ways:
MANUAL
SEARCH
SMARTPHONE
TABLET - WEB
ACTIVATION OF REMOTE CONTROL
SELECTION OF OPERATING MODE
Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control
INSERTING THE BATTERIES
SAFETY WARNINGS
The remote control and batteries should not be exposed to excessive heat such as sunlight, re
or the like.
The product . Keep out of reach of children or domestic animals. is not a toy
Use the -code on the side or connect to the page and follow the instructions. qr www.cme.it
Once you have found the specic code for your device, set it in the remote control as described in the
ENTERING THE CODE DIRECTLY chapter.
ATTENTION : searching for the suitable code could last up to 5 minutes.
• Stand in front of the device to be controlled and make sure it is ON (not in stand-by). If necessary, switch
it on using the original remote control (if this is still working) or the buttons present on the device itself. (on
TVs they can be on the side or the top)
• On the MELICONI remote control and then press and hold the butt until select the operating mode on
the LED of the remote control lights up; lease. re
• Pointing the remote control towards the device, PRESS AND HOLD butt and wait the ON/OFF on
(even up to 5 minutes) for the device to switch o.
• , w the device turn o IMMEDIATELY RELEASE the button. PAY ATTENTION hen ,
• Three nal ashes indicate that the operation has been completed successfully.
(only to be performed if you know the to be set) specic code
• On the MELICONI remote control and then press and hold the button until select the operating mode
the LED lights up; release.
• Immediately enter the previously identied specic code.
• Three nal ashes indicate that the operation has been completed successfully.
If necessary it is possible to reset the remote control and bring it back to the initial conditions. completely
WARNING : All user settings will be lost. Operate as follows:
• On the MELICONI remote control press and hold the button until the LED lights up; release.
• Enter the code . 0100
• Three nal ashes indicate that the operation has been completed successfully.
RESET THE REMOTE CONTROL
If the remote control does NOT carry out the three nal ashes, the setting is NOT successful; repeat the procedure.
If still unsuccessful, it means that the code is not included in the remote control, contact the ASSISTANCE.
ENTERING THE CODE DIRECTLY
VERIFY
Check that the MELICONI remote control operates your device the main functions if it does not, the in ; REPEAT
procedure.
NOTE: When the list of codes to be searched is over, the remote control exits the search and the LED remains o.
If no results are obtained, try using the procedure described in the SMARTPHONE - TABLET - WEB chapter or contact
the ASSISTANCE.
MANUAL SEARCH
SMARTPHONE - TABLET - WEB

Produkt Specifikationer

Mærke: Meliconi
Kategori: Fjernbetjening
Model: Speedy 2.1

Har du brug for hjælp?

Hvis du har brug for hjælp til Meliconi Speedy 2.1 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Fjernbetjening Meliconi Manualer

Meliconi

Meliconi fully 8 Manual

12 Januar 2025
Meliconi

Meliconi gumbody light facile Manual

23 September 2024
Meliconi

Meliconi universal 4 Manual

22 September 2024
Meliconi

Meliconi Pratico 2 Manual

18 September 2024
Meliconi

Meliconi Personal 2 plus Manual

29 August 2024
Meliconi

Meliconi Speedy 2.1 Manual

21 August 2024
Meliconi

Meliconi GumBody Light Manual

21 August 2024
Meliconi

Meliconi Pratico 2.1 Manual

20 August 2024
Meliconi

Meliconi Gumbody Personal 7 plus Manual

20 August 2024
Meliconi

Meliconi Gumbody Personal 2 Manual

20 August 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

URC

URC Complete Control MX-4000 Manual

17 Juli 2025
URC

URC Total Control TRC-1080 Manual

17 Juli 2025
URC

URC Total Control TDC-9100 Manual

17 Juli 2025
URC

URC MRX-4IR Manual

17 Juli 2025
URC

URC MX-990 Manual

17 Juli 2025
URC

URC Total Control MRX-5 Manual

17 Juli 2025
URC

URC Total Control TDC-7100 Manual

17 Juli 2025
URC

URC Total Control TRC-1120 Manual

17 Juli 2025
Rockville

Rockville RockerBT Manual

15 Juli 2025
Rockville

Rockville RockerBT V2 Manual

15 Juli 2025