Microchip HV853DB1 Manual


Læs nedenfor 📖 manual på dansk for Microchip HV853DB1 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Supertex inc.
Supertex inc.
www.supertex.com
HV853DB1
Doc.# DSDB-HV853DB1
A032813
General Description
The Supertex HV853DB1 demoboard contains all the
necessary circuitry to demonstrate the features of the HV853
EL lamp driver. The HV853 is the low noise version of the EL
driver HV852 with improved EMI performance.
Simply connect it to a power supply and a lamp as shown in
Figure 1. For additional assistance with the HV853 demoboard
circuit, please refer to the HV853 datasheet.
High Voltage, Low Noise, Inductorless
EL Lamp Driver Demoboard
Specications
Parameter Value
Input voltage: 3.2V to 5.0V
Supply current: 18mA
Lamp size: 0.93in2 and 1.5in2
Lamp frequency: 274Hz
Connections:
VDD (IC Supply)
Supplies the HV853 EL driver IC. The supplied demoboard
is optimized for 3.2 to 5.0V operation.
EN (Enable Input)
A logic input which enables/disables the driver. Connect
EN to logic high (VDD) to enable the driver and to logic low
(GND) to disable the driver. This input may be connected to
a mechanical switch or to a logic circuit output.
CLKIN (Clock Input)
A logic input pin to which an external clock can be applied to
set the EL lamp frequency. CLKEN has to be connected to
VDD when external clock input is used. Also, the REL resistor
needs to be removed and the REL pin needs to be connected
to ground. Connect CLKIN to GND if not used.
GND (Circuit Ground)
Connect to VDD negative terminal. Supply bypass capaci-
tor for VDD is provided on the demoboard. External supply
bypass capacitors are not required.
VA and VB (Lamp Connections)
They connect to EL lamp terminals. Polarity is irrelevant.
CLKEN (Clock Enable)
Logic input pin which enables/disables the external clock ap-
plied. Logic high (VDD) will cause the EL lamp frequency to
be set by the CLKIN input. Logic low (GND) will cause the EL
lamp frequency to be set by the external REL resistor.
Note:
All of the above connections must be made before powering up the supply voltages.
Board Layout and Connection Diagram
Actual Dimensions: 13mm x 8mm
VDD
EN
CLKIN
GND
VA
VB
CLKEN


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: HV853DB1

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip HV853DB1 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Märklin

Märklin 72886 Manual

24 Januar 2025
Märklin

Märklin 72797 Manual

24 Januar 2025
Märklin

Märklin 7001 Manual

24 Januar 2025
Hilti

Hilti KCC-WF Manual

24 Januar 2025
Märklin

Märklin 7051 Manual

24 Januar 2025
ATen

ATen KH1516Ai Manual

24 Januar 2025
Adonit

Adonit PD-3A2C Manual

24 Januar 2025
Adonit

Adonit Dash 4 Manual

24 Januar 2025