Microchip HV861 Manual


Læs nedenfor 📖 manual på dansk for Microchip HV861 (18 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/18
2023 Microchip Technology Inc. and its subsidiaries DS20005911A-page 1
HV861
Features
Adjustable Output Regulation for Dimming
Lamp Fade-in/Fade-out Capability
Low Audible Noise
180 VPP Output Voltage for Higher Brightness
1.5V Enable Input Logic High
Single-cell Lithium Ion-compatible
One Miniature Inductor to Power both Lamps
Separately Adjustable Lamp and Converter
Frequencies
Split Supply Capability
Applications
Dual Display Cellular Phones
Keypad and LCD Backlighting
Personal Digital Assistant (PDA)
Handheld Wireless Communication Products
Global Positioning Systems (GPS)
General Description
The HV861 is a low-noise dimmable high-voltage dual EL
lamp driver designed for driving two electroluminescent
(EL) lamps with a combined area of 5 in2. The input
supply voltage range is from 2.5V to 4.5V. Enable input
logic high can go as low as 1.5V, which allows logic
interface operating from typical 1.8V supplies. The
device is designed to minimize audible noise emitted by
the EL lamps.
The device uses a single inductor and a minimum
number of passive components. With the internal
reference voltage, the regulated output voltage is at a
nominal value of 90V. The EL lamps therefore see ±90V.
The two EL lamps can be turned on and turned off using
two CMOS logic inputs, EN1 and EN2. The driver is
disabled when both EN1 and EN2 are at logic low.
The HV861 has two internal oscillators, a switching
MOSFET, and two high-voltage EL lamp driver
H-bridges. Each driver has its own half-bridge common
output, COM1 and COM2, which significantly minimizes
the DC offset seen by the EL lamp. The frequency for the
switching MOSFET is set by an external resistor
connected between the R SW-Osc pin and the supply pin,
VDD. The EL lamp driver frequency is set by an external
resistor connected between the REL-Osc pin and the VDD
pin. An external inductor is connected between the L X
and VDD pins or VIN for split supply applications.
Depending upon the EL lamp sizes, a 1 nF to 10 nF
capacitor is connected between the C S and ground. As
the switching MOSFET charges the external inductor
and discharges it into the capacitor at CS, the voltage at
CS starts to increase. Once the voltage at C S reaches a
nominal value of 90V, the switching MOSFET is turned
off to conserve power.
EL lamp dimming can be accomplished by applying a
PWM logic signal to the PWM pin. The EL lamp
brightness will be inversely proportional to the PWM duty
cycle. The HV861 can also slowly turn on or turn off the
EL lamp, giving a fade on/off appearance.
Package Type
See Table 2-1 for pin information.
16-lead WQFN
(Top view)
1 12
2
3
4
5 6 7 8
9
10
11
13141516
VREF VREG VOUT PWM
EL1
COM1
COM2
EL2
REL-Osc
RSW-Osc
VDD
EN1
EN2 GND LX CS
Low-Noise Dimmable Dual EL Lamp Driver


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: HV861

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip HV861 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Microchip

Microchip ATECC608B Manual

4 September 2024
Microchip

Microchip HV860 Manual

4 September 2024
Microchip

Microchip EVB-LAN9255 Manual

4 September 2024
Microchip

Microchip LX4580 Manual

4 September 2024
Microchip

Microchip LX7720 Manual

4 September 2024
Microchip

Microchip AT32UC3A364 Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024