Microchip HV9912 Manual


Læs nedenfor 📖 manual på dansk for Microchip HV9912 (20 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/20
2016 Microchip Technology Inc. DS20005583A-page 1
HV9912
Features
Switch-mode Controller for Single-switch Drivers:
- Buck
- Boost
- Buck-boost
- SEPIC
Works with High-side Current Sensors
Closed-loop Control of Output Current
High Pulse-Width Modulation (PWM) Dimming
Ratio
Internal 90V Linear Regulator (can be extended
using external Zener Diodes)
Internal 2% Voltage Reference (0°C < T
A < 85°C)
Constant Frequency or Constant Off-time
Operation
Programmable Slope Compensation
Linear and PWM Dimming
+0.2A/–0.4A Gate Driver
Hiccup Mode Protection for both Short-circuit and
Open-circuit Conditions
Output Overvoltage Protection
Synchronization Capability
Pin Compatible with HV9911
Applications
RGB Backlight Applications
General LED Lighting Applications
Battery-powered LED Lamps
General Description
HV9912 is an LED driver IC designed to control
single-switch PWM converters (buck, boost,
buck-boost and SEPIC) in a Constant Frequency or
Constant Off-time mode. The controller uses a peak
Current Mode control scheme with programmable
slope compensation and includes an internal
transconductance amplifier to control the output current
in closed loop, enabling high output current accuracy.
In the case of buck and buck-boost converters, the
output current can be sensed using a high-side current
sensor like the HV7800. In the Constant Frequency
mode, multiple HV9912 ICs can be synchronized with
each other or with an external clock, using the SYNC
pin. Programmable MOSFET current limit enables
current limiting during Input Undervoltage and Output
Overload conditions. The IC also includes a 0.2A
source and 0.4A sink gate driver that makes the
HV9912 suitable for high-power applications. An
internal 90V linear regulator powers the IC, eliminating
the need for a separate power supply for the IC. The IC
also provides a FAULT output, which can be used to
disconnect the LEDs in case of a Fault condition using
an external disconnect FET. HV9912 also provides a
TTL-compatible, low-frequency PWM dimming input
that can accept an external control signal with a duty
ratio of 0-100% and a frequency of up to a few kilohertz.
The HV9912 includes hiccup protection from both short
and open circuits, with automatic recovery after the
Fault condition is cleared.
The HV9912 is a pin-compatible replacement for
HV9911. It can be used with existing HV9911 designs,
which have input voltages of less than 90V, by
changing ROVP1, ROVP
, and RT
.
Package Type
VIN
VDD
GATE
GND
CS
SC
RT
SYNC
FDBK
IREF
COMP
PWMD
OVP
FAULT
REF
CLIM
1
2
3
4
5
6
7
8 9
10
11
12
13
14
15
16
16-lead SOIC
(Top View)
See Table 2-1 for pin information.
Switch-Mode LED Driver IC with High Current Accuracy
and Hiccup Mode Protection


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: HV9912

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip HV9912 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Microchip

Microchip PD81101 Manual

23 December 2024
Microchip

Microchip ATECC608B Manual

4 September 2024
Microchip

Microchip HV860 Manual

4 September 2024
Microchip

Microchip EVB-LAN9255 Manual

4 September 2024
Microchip

Microchip LX4580 Manual

4 September 2024
Microchip

Microchip LX7720 Manual

4 September 2024
Microchip

Microchip AT32UC3A364 Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024