Microchip MIC2127 Manual


Læs nedenfor 📖 manual på dansk for Microchip MIC2127 (36 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/36
2016-2020 Microchip Technology Inc. DS20005676F-page 1
MIC2127A
Features
Hyper Speed Control® Architecture Enables:
- High input to output voltage conversion ratio
capability
- Any Capacitor™ stable
- Ultra-fast load transient response
Wide 4.5V-75V Input Voltage Range
Adjustable Output Voltage from 0.6V to 30V
270 kHz-800 kHz Programmable Switching
Frequency
Built-In 5V Regulator for Single-Supply Operation
Auxiliary Bootstrap LDO for Improving System
Efficiency
Internal Bootstrap Diode
Selectable Light Load Operating Mode
Enable Input and Power Good Output
Programmable Current Limit
Hiccup Mode Short-Circuit Protection
Soft Start, Internal Compensation and Thermal
Shutdown
Supports Safe Start-Up into a Prebiased Output
AEC-Q100 Qualified (VAO suffix)
Applications
Networking/Telecom Equipment
Base Station, Servers
Distributed Power Systems
Industrial Power Supplies
Automotive Power Supplies
General Description
The MIC2127A device is a constant-frequency
synchronous buck controller featuring a unique
adaptive on-time control architecture. The MIC2127A
device operates over an input voltage range from
4.5V-75V. The output voltage is adjustable down to
0.6V with an accuracy of ±1%. The device operates
with programmable switching frequency from 270 kHz
to 800 kHz.
The MIC2127A device features a MODE pin that allows
the user to select either Continuous Conduction mode
or HyperLight Load® (HLL) mode under light loads. An
auxiliary bootstrap LDO improves the system efficiency
by supplying the MIC2127A internal circuit bias power
and gate drivers from the output of the converter. A
logic level enable (EN) signal can be used to enable or
disable the controller. MIC2127A can start-up
monotonically into a prebiased output. The MIC2127A
device features an open drain power good signal (PG)
that signals when the output is in regulation and can be
used for simple power supply sequencing.
MIC2127A offers a full suite of protection features to
ensure protection of the IC during Fault conditions.
These include undervoltage lockout to ensure proper
operation under power-sag conditions, “hiccup” mode
short-circuit protection, internal soft start of 5 ms to
reduce inrush current during start-up and thermal shut-
down.
The MIC2127A device is available in a 16-pin
3 mm × 3 mm VQFN package, with an operating
junction temperature range from –40°C to +125°C.
Typical Application Circuit
PVDD
VDD
PG
EN
MODE
FREQ EXTVDD
FB
ILIM
SW
BST
VIN VIN
4.5V*
to 75V
VOUT
5V@5A
VOUT
VIN
4.7 μF
2.2 μFX3
47 μF
10 μH
0.1 μF
0.1 μF
4.7 nF
1 μF
4.7 μF
10
36 k
7.5 k
1 k
100 k
60 k
1.3 k
VIN
MIC2127A
PGND
AGND
DH
DL
330 μF
+
0.1 μF
Q1
Q2
Q1,Q3: SiR878ADP
L1: SRP1265A-100M, Bourns
C1: 10SVP330M
*Output voltage follows input voltage when the input is below the target output voltage
L1
C1
VDD
75V, Synchronous Buck Controller Featuring Adaptive
On-Time Control


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: MIC2127

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC2127 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Microchip

Microchip PD81101 Manual

23 December 2024
Microchip

Microchip ATECC608B Manual

4 September 2024
Microchip

Microchip HV860 Manual

4 September 2024
Microchip

Microchip EVB-LAN9255 Manual

4 September 2024
Microchip

Microchip LX4580 Manual

4 September 2024
Microchip

Microchip LX7720 Manual

4 September 2024
Microchip

Microchip AT32UC3A364 Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024