Microchip MIC33M356 Manual


Læs nedenfor 📖 manual på dansk for Microchip MIC33M356 (44 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 2 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/44
2020 Microchip Technology Inc. DS20006349A-page 1
MIC33M356
Features
Input Voltage Range: 2.4V to 5.5V
3A Output Current
Multiple Faults Indication through I
2C
• I2C Programmable:
- Output voltage:
0.6V to 1.28V at 5 mV resolution or
0.6V to 3.84V, 10 and 20 mV resolution
- Slew rate: 0.2 ms/V to 3.2 ms/V
- On-time (switching frequency)
- High-side current limit: 3.5A or 5A
- Enable delay: 0.2 ms-3 ms
- Output discharge when disabled (EN = GND)
High Efficiency (up to 95%)
Ultra-Fast Transient Response
±1.5% Output Voltage Accuracy Over
Line/Load/Temperature Range
Safe Start-up with Pre-Biased Output
Typical 1.5 µA Shutdown Supply Current
Low Dropout (100% Duty Cycle) Operation
• I2C Speed Up to 3.4 MHz
Latch-Off Thermal Shutdown Protection
Latch-Off Current Limit Protection
Power Good (PG) Open-Drain Output
Meets the CISPR32 Class B Emissions
Applications
Solid-State Drives (SSD)
Tablets, Notebooks and Ultrabooks
FPGAs, DSP and Low-Voltage ASIC Power
General Description
The Microchip MIC33M356 is a I2C programmable,
high-efficiency, low-voltage input, 3A current, synchro-
nous step-down regulator power module with
integrated inductor. The Constant On-Time (COT)
control architecture with HyperLight Load
® mode
provides very high efficiency at light loads, while still
having ultra-fast transient response.
The I2C interface allows programming the output volt-
age between 0.6V and 1.28V, with 5 mV resolution or
between 0.6V and 3.84V, with 10 mV and 20 mV reso-
lution. Two different default voltage options (0.9V and
1.0V) are provided so that the application can be
started with a safe voltage level and then moved to
high-performance modes under I2C control.
An open-drain Power Good output facilitates output
voltage monitoring and sequencing. If set in shutdown
(EN = GND), the MIC33M356 typically draws 1.5 µA of
current, while the output is discharged through a 10
pull-down resistor (if the output discharge feature is
enabled).
The MIC33M356 pinout is compatible with the
Microchip MIC33M350, so that applications can be
easily converted.
The 2.4V to 5.5V input voltage range, low shutdown and
quiescent currents make the MIC33M356 ideal for
single-cell Li-Ion battery-powered applications. The 100%
duty cycle capability provides low dropout operation,
extending operating range in portable systems.
The MIC33M356 is available in a thermally-efficient,
24-lead, 3.0 mm × 4.5 mm × 1.8 mm QFN package,
with an operating junction temperature range of -40°C
to +125°C.
FIGURE 1: Radiated Emissions,
CISPR32, Class B (VIN = 5V, VOUT = 1V,
IOUT = 3A).
3A, Power Module Buck Converter
with HyperLight Load® Mode and I2C Interface


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: MIC33M356

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC33M356 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Microchip

Microchip PD81101 Manual

23 December 2024
Microchip

Microchip ATECC608B Manual

4 September 2024
Microchip

Microchip HV860 Manual

4 September 2024
Microchip

Microchip EVB-LAN9255 Manual

4 September 2024
Microchip

Microchip LX4580 Manual

4 September 2024
Microchip

Microchip LX7720 Manual

4 September 2024
Microchip

Microchip AT32UC3A364 Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024