Microchip MIC5322 Manual


Læs nedenfor 📖 manual på dansk for Microchip MIC5322 (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/4
MIC5322 Evaluation Board
High Performance Dual 150mA
µCap ULDO™
ULDO is a trademark of Micrel, Inc.
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (
408
) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
March 2008 M9999-032708-A
General Description
The MIC5322 is a tiny dual output, ultra low dropout linear
regulator. The MIC5322 regulator provides a single active
low enable pin for both outputs as well as a bypass pin to
reduce the output voltage noise. The MIC5322 provides
two high performance 150mA LDOs in a tiny 6 pin 1.6mm
x 1.6mm Thin MLF
®
package.
The MIC5322 dual Ultra Low Dropout (ULDO™) linear
regulator is easy to use. A small capacitance of only 1µF is
required for the input voltage and each of the outputs to
maintain stability. A bypass capacitor of 0.01µF is included
on the evaluation board to reduce the output voltage noise
and improve the Power Supply Rejection Ratio (PSRR).
The evaluation board includes an input capacitor of 10µF
to compensate for long inductive test leads.
Requirements
The MIC5322 evaluation board requires an input power
source that is able to deliver at least 300mA at a voltage
within the range of 2.3V to 5.5V. The output load can be
either active or passive.
Precautions
The evaluation board does not have reverse polarity
protection. Applying a negative voltage to the V
IN
terminal
may damage the device.
The evaluation board is tailored for a Li-Ion range input
supply voltage. It should not exceed 5.5V on the input.
Getting Started
1. Connect an external supply to V
IN
. Apply the
desired input voltage to the V
IN
(J1) and ground
terminal (J2) of the evaluation board, paying
careful attention to polarity and supply voltage
(2.3V V
IN
5.5V). An ammeter may be placed
between the input supply and the V
IN
terminal to
the evaluation board to accurately monitor the
input current. The ammeter and/or power lead
resistance can reduce the voltage supplied to the
input so monitor the supply voltage at the V
IN
terminal.
2. Enable/Disable the MIC5322. The evaluation
board is set up for “Default Disable on both
outputs with a 10k pull up resistor on the enable
pin (/EN) to V
IN
. To enable both outputs, simply
jumper the /EN terminal (J7) to the GND terminal
(J2 or J5). The enable pin must be either pulled
high or low for proper operation. Removing the pull
up resistors and leaving the pin floating will cause
the regulators to operate in an indeterminate state.
3. Connect the loads to the V
OUT
terminals (J4 for
LDO1, J6 for LDO2) and ground terminal (J5).
The load can be either a passive (resistor) or
active (electronic load). Be sure to monitor the
output voltage at the V
OUT
(J4 and J6) terminals.
Ordering Information
Part Number Description
MIC5322-XXYMT EV
Evaluation board with the 150mA
Dual ULDO™ device with bypass
and active low enable


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: MIC5322

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC5322 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Microchip

Microchip PD81101 Manual

23 December 2024
Microchip

Microchip ATECC608B Manual

4 September 2024
Microchip

Microchip HV860 Manual

4 September 2024
Microchip

Microchip EVB-LAN9255 Manual

4 September 2024
Microchip

Microchip LX4580 Manual

4 September 2024
Microchip

Microchip LX7720 Manual

4 September 2024
Microchip

Microchip AT32UC3A364 Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024