Microchip PIC32MX120F064H Manual

Microchip Ikke kategoriseret PIC32MX120F064H

Læs nedenfor 📖 manual på dansk for Microchip PIC32MX120F064H (84 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/84
2007-2021 Microchip Technology Inc. DS60001145AA-page 1
PIC32
1.0 DEVICE OVERVIEW
This document defines the Flash programming
specification for the PIC32 family of 32-bit
microcontrollers.
This programming specification is designed to guide
developers of external programmer tools. Customers
who are developing applications for PIC32 devices
should use development tools that already provide
support for device programming.
The major topics of discussion include:
Section 1.0 “Device Overview”
Section 2.0 “Programming Overview”
Section 3.0 “Programming Steps”
Section 4.0 “Connecting to the Device
Section 5.0 “EJTAG vs. ICSP
Section 6.0 “Pseudo Operations”
Section 7.0 “Entering 2-Wire Enhanced ICSP
Mode”
Section 8.0 “Check Device Status”
Section 9.0 “Erasing the Device
Section 10.0 “Entering Serial Execution Mode”
Section 11.0 “Downloading the Programming
Executive (PE)”
Section 12.0 “Downloading a Data Block”
Section 13.0 “Initiating a Page Erase”
Section 14.0 “Initiating a Flash Row Write”
Section “”
Section 16.0 “Exiting Programming Mode”
Section 17.0 “The Programming Executive”
Section 18.0 “Checksum”
Section 19.0 “Configuration Memory and Device
ID”
Section 20.0 “TAP Controllers”
Section 21.0 “AC/DC Characteristics and Timing
Requirements”
Appendix A: “PIC32 Flash Memory Map”
Appendix B: “Hex File Format”
Appendix C: “Device IDs”
Appendix D: “Revision History”
2.0 PROGRAMMING OVERVIEW
When in development of a programming tool, it is
necessary to understand the internal Flash program
operations of the target device and the Special
Function Registers (SFRs) used to control Flash
programming, as these same operations and registers
are used by an external programming tool and its
software. These operations and control registers are
described in the “Flash Program Memory” chapter in
the specific device data sheet, and the related “PIC32
Family Reference Manual” section. It is highly
recommended that these documents be used in
conjunction with this programming specification.
An external tool programming setup consists of an
external programmer tool and a target PIC32 device.
Figure 2-1 illustrates a typical programming setup. The
programmer tool is responsible for executing
necessary programming steps and completing the
programming operation.
FIGURE 2-1: PROGRAMMING SYSTEM
SETUP
Target PIC32 Device
CPU
On-Chip Memory
External
Programmer
PIC32 Flash Programming Specification


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: PIC32MX120F064H

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip PIC32MX120F064H stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Microchip

Microchip ATECC608B Manual

4 September 2024
Microchip

Microchip HV860 Manual

4 September 2024
Microchip

Microchip EVB-LAN9255 Manual

4 September 2024
Microchip

Microchip LX4580 Manual

4 September 2024
Microchip

Microchip LX7720 Manual

4 September 2024
Microchip

Microchip AT32UC3A364 Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Alpine

Alpine SBS-0515 Manual

8 November 2024
Alpine

Alpine KCE-103V Manual

8 November 2024
Alpine

Alpine KCE-104V Manual

8 November 2024
Advantech

Advantech ECU-1051TL Manual

8 November 2024
Alpine

Alpine DDC-R13A Manual

8 November 2024
Alpine

Alpine HCE-C200F Manual

8 November 2024
Alpine

Alpine CRM-1652RF Manual

8 November 2024
Alpine

Alpine KIT-8MBF Manual

8 November 2024
Alpine

Alpine APF-D200MB Manual

8 November 2024
Alpine

Alpine CDM-9803RR Manual

8 November 2024