Microchip PL485-EK Manual


Læs nedenfor 📖 manual på dansk for Microchip PL485-EK (41 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/41
PL485-EK
PL485-EK User Guide
Introduction
PL485-EK is an evaluation kit for the PL485. PL485 is a programmable System On Chip (SOC) for narrow-band
Power Line Communication (PLC) from Microchip Technology Inc, able to run any PLC protocol in the frequency
band below 500 kHz. Depending on the running firmware, PL485 is able to support applications not only for basic
connectivity (point to point or point to multi-point connectivity) but also for complex mesh network topologies.
The PL485-EK board has been conceived to communicate in the CENELEC B-Band (95 kHz to 125 kHz) and
complies with the CENELEC EN 50065 standard. It is designed to be directly connected to low voltage DC power
rails and optionally to AC mains by means of an external coupler accessory. Please refer to PLC-AC-Coupler User
Guide for more information about the AC coupler accessory.
Contents
Welcome letter
• Board:
One PL485-EK board
• Cable:
One Micro A/B-type USB cable
Kit contents are protected with anti-static foam. The PL485-EK board is shipped in an anti-static shielding bag.
WARNING
The board must not be subject to high electrostatic discharges. It is recommended to use a grounding
strap or similar ESD protective device when handling the board in hostile ESD environments. Avoid
touching the component pins or any other metallic element on the board.
Features
PL485-EK board includes a PL485 system on chip, able to run any PLC protocol in the <500 kHz band.
PL485-EK board implements a coupling circuit optimized for the band 95kHz to 125 kHz, compliant with
CENELEC standard EN50065.
SWD/JTAG interface for MCU debugging and programming purposes. PL485-EK board includes as well a USB
Embedded Debugger (EDBG) for on-board debugging.
USB 2.0 full-speed interface
• mikroBUS socket connector to interface with other circuits and add-on boards.
Xplained PRO header connector (master) to interface with other circuits and add-on boards.
RESET push button, ERASE jumper.
Voltage monitor circuit on the 5V rail, or alternatively on the 3.3V rail with minor modifications.
PL485-EK board can be powered from the following sources:
Micro-B USB connector (J5)
Micro-B USB connector (J12)
© 2020 Microchip Technology Inc. User Guide DS50002954B-page 1


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: PL485-EK

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip PL485-EK stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Märklin

Märklin 72886 Manual

24 Januar 2025
Märklin

Märklin 72797 Manual

24 Januar 2025
Märklin

Märklin 7001 Manual

24 Januar 2025
Hilti

Hilti KCC-WF Manual

24 Januar 2025
Märklin

Märklin 7051 Manual

24 Januar 2025
ATen

ATen KH1516Ai Manual

24 Januar 2025
Adonit

Adonit PD-3A2C Manual

24 Januar 2025
Adonit

Adonit Dash 4 Manual

24 Januar 2025