Microchip TC962 Manual


Læs nedenfor 📖 manual på dansk for Microchip TC962 (14 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/14
2001-2012 Microchip Technology Inc. DS21484D-page 1
TC962
Features:
Pin Compatible With TC7662/ICL7662/SI7661
High Output Current 80 mA
No External Diodes Required
Wide Operating Range 3V to 18V
Low Output Impedance 28 Typ.
No Low Voltage Terminal Required
Application Zener On-Chip
OSC Frequency Doubling Pin Option for Smaller
Output Capacitors
Applications:
Laptop Computers
Disk Drives
Process Instrumentation
P-Based Controllers
Device Selection Table
General Description:
The TC962 is an advanced version of the industry
standard TC7662 high voltage DC-to-DC converter.
Using improved design techniques and CMOS
construction, the TC962 can source as much as 80 mA
versus the 7662’s 20 mA capability.
As an inverter, the TC962 can put out voltages as high
as 18V and as low as 3V without the need for external
diodes. The output impedance of the device is a low
28 (with the proper capacitors), voltage conversion
efficiency is 99.9%, and power conversion efficiency is
97%.
The low voltage terminal (pin 6) required in some
TC7662 applications has been eliminated. Grounding
this terminal will double the oscillator frequency from 12
kHz to 24 kHz. This will allow the use of smaller
capacitors for the same output current and ripple, in
most applications. Only two external capacitors are
required for inverter applications. In the event an
external clock is needed to drive the TC962 (such as
paralleling), driving this pin directly will cause the
internal oscillator to sync to the external clock.
Pin 1, which is used as a test pin on the 7662, is a
voltage reference Zener on the TC962. This Zener (6.4V
at 5 mA) has a dynamic impedance of 12 and is
intended for use where the TC962 is supplying current to
external regulator circuitry and a reference is needed for
the regulator circuit. (See Section 3.0 “Applications
Information” Applications Information).
The TC962 is compatible with the LTC1044, SI7661
and ICL7662. It should be used in designs that require
greater power and/or less input to output voltage drop.
It offers superior performance over the ICL7660S.
Package Type
Part
Number Package
Operating
Temp.
Range
TC962COE 16-Pin SOIC Wide 0°C to +70°C
TC962CPA 8-Pin Plastic DIP 0°C to +70°C
TC962EPA 8-Pin Plastic DIP -40°C to +85°C
TC962IJA 8-Pin CERDIP -25°C to +85°C
TC962MJA 8-Pin CERDIP -55°C to +125°C
VDD
1
2
3
4
5
6
7
8
16
13
12
11
10
9
NC
GND
COSC
NC
15
14
NC
NC
NC
TC962COE
NC
NC
Zener
Cathode
NC
FREQ x 2
16-Pin SOIC Wide
C+
CVOUT
1
2
3
4
8
7
6
5
FREQ x 2GND
TC962CPA
TC962EPA
TC962IJA
TC962MJA
C+
CVOUT
8-Pin CERDIP
8-Pin DIP
Zener
Cathode
COSC
VDD
High Current Charge Pump DC-to-DC Converter


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: TC962

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip TC962 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Microchip

Microchip PD81101 Manual

23 December 2024
Microchip

Microchip ATECC608B Manual

4 September 2024
Microchip

Microchip HV860 Manual

4 September 2024
Microchip

Microchip EVB-LAN9255 Manual

4 September 2024
Microchip

Microchip LX4580 Manual

4 September 2024
Microchip

Microchip LX7720 Manual

4 September 2024
Microchip

Microchip AT32UC3A364 Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024