Microchip USB2229 Manual


Læs nedenfor 📖 manual på dansk for Microchip USB2229 (5 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/5
SMSC AN 14.18 APPLICATION NOTE Revision 0.96 (06-01-06)
AN 14.18
Design Guidelines for
USB22XX/USB260X
High-Speed SD
1 Introduction
This application note provides information on Printed Circuit Board layout for High-Speed Secure-Digital
(SD) media sockets with USB22XX and USB260X.
2 Overview
Successful High-Speed operation of Secure-Digital media with USB22XX and USB260X requires
special consideration for Printed Circuit Board (PCB) layout. This application note describes the
important items to consider for layout of PCB.
3 PCB Layout Guidelines
The guidelines presented are applicable to all SMSC card-reader products that support High-Speed
Secure-Digital operation. Guidelines for both two-layer and four-layer PCBs are presented here.
3.1 Power and Ground Distribution to SD Socket
Ground connection between the card-reader and the media socket is important, both for supply return
current and signal return currents. The ground should be solid, have low impedance and few
constrictions between the card-reader and the socket. The card-reader supplies the power to the socket
in most applications since the power-FET is built-in to the SMSC card-reader.
SD socket VDD supply trace from card-reader should be 20 mils wide, 0.5 oz or thicker for a length
up to 3000 mils.
SD socket ground connection: plane, 0.5 oz or thicker, between socket and card-reader.
Note: No constrictions or cuts allowed in the ground between card-reader and socket.
3.2 Signal Traces to SD Socket
The Secure-Digital interface has a total of seven signals to the card-reader. Six of these signals are
critical for high-speed operation: SD_DAT[0:3], SD_CMD and SD_CLK and require special
considerations.
Signal traces must be above a solid and continuous ground plane along the path from card-reader
to socket.
SD_CLK trace requires two grounded guard-traces, one on each side spaced, at 3 times minimum
spacing.
SD_CLK guard traces must have a via connecting to the ground plane at both ends and every 500
mils along the path.


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: USB2229

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip USB2229 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Microchip

Microchip ATECC608B Manual

4 September 2024
Microchip

Microchip HV860 Manual

4 September 2024
Microchip

Microchip EVB-LAN9255 Manual

4 September 2024
Microchip

Microchip LX4580 Manual

4 September 2024
Microchip

Microchip LX7720 Manual

4 September 2024
Microchip

Microchip AT32UC3A364 Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Gigabyte

Gigabyte ODIN GT 550W Manual

23 November 2024
Stamos

Stamos S-PLASMA 60U Manual

23 November 2024
Velbus

Velbus VMBPIRO-W-20 Manual

23 November 2024
Honor

Honor 90 Pro Manual

23 November 2024
Honor

Honor 80 SE Manual

23 November 2024
Medela

Medela Safe & Dry Manual

22 November 2024
Jane

Jane First Potty Manual

22 November 2024