Microchip USB3327 Manual


Læs nedenfor 📖 manual på dansk for Microchip USB3327 (7 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/7
2008-2019 Microchip Technology Inc. DS00002959A-page 1
INTRODUCTION
For customers who want to integrate the USB3320 and are looking to the USB3340/USB83340 for future products, this
document describes the hardware and software considerations required to accomplish that migration with the least
impact to customer design resources. By following the design guidelines outlined in this document, a designer can use
a common PCB and software platform that can be used for both the USB3320 and USB3340/USB83340 with nothing
more than a change to the Bill of Materials (BOM) being required.
REFERENCES
Microchip USB Transceiver Data Sheets:
• USB3320
• USB334x
• USB83340
DESIGNING A COMMON PCB FOR THE USB3320 AND USB3340/USB83340
A common PCB design can be engineered to support both the USB3320 and USB3340/USB83340 transceivers.
Observing a few simple design considerations will provide a seamless transition from USB3320 to USB3340/
USB83340. Unless otherwise specified within this document, all PCB layout design guidelines that apply to the
USB3320 shall apply to the USB3340/USB83340.
To design a common hardware platform for both USB transceivers, there are three design changes that must be made:
Depopulate or disable the 1.8V regulator input.
Change the capacitor on the VDD18 pin from a 0.1
F to a 1.0
F low-ESR capacitor.
VBAT min voltage raised from 3.1V to 4.0V for the USB83340 only. (USB3340 VBAT min voltage lowered to 3.0V).
Other optional changes that can be made:
Change the capacitor on the VDD33 pin from a 2.2
F low-ESR to a 1.0
F low-ESR Capacitor.
Change the resister on the RVBUS pin from a 10k to 20k resistor.
Integrating the 1.8V Regulator
The USB3340/USB83340 integrates the 1.8V regulator that was external to the USB3320. The VDD18 pin of the
USB3320 is an input and requires an external voltage source to be applied to the pin. Conversely, the VDD18 pin of the
USB3340/USB83340 is an output that must never be presented with an externally sourced voltage.
AN 19.0
Migrating USB Designs from the USB3320 to the
USB3340/USB83340


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: USB3327

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip USB3327 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Märklin

Märklin 72886 Manual

24 Januar 2025
Märklin

Märklin 72797 Manual

24 Januar 2025
Märklin

Märklin 7001 Manual

24 Januar 2025
Hilti

Hilti KCC-WF Manual

24 Januar 2025
Märklin

Märklin 7051 Manual

24 Januar 2025
ATen

ATen KH1516Ai Manual

24 Januar 2025
Adonit

Adonit PD-3A2C Manual

24 Januar 2025
Adonit

Adonit Dash 4 Manual

24 Januar 2025