Mikrotik RB951Ui-2HnD Manual

Mikrotik Adgangspunkt RB951Ui-2HnD

Læs nedenfor 📖 manual på dansk for Mikrotik RB951Ui-2HnD (6 sider) i kategorien Adgangspunkt. Denne guide var nyttig for 32 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/6

RB951-series

RB951-seriesRB951-series

RouterBOARD 951 series models:

RouterBOARD 951 series models:RouterBOARD 951 series models:

RB951Ui-2HnD

RB951G-2HnD

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

Exposure to Radio Frequency Radiation:

Exposure to Radio Frequency Radiation: Exposure to Radio Frequency Radiation: This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an

uncontrolled environment.This MikroTik device should be installed and operated no closer than 20 centimeters from your body, occupational user, or the

general public.

First Steps:

This device is a simple home wireless access point. It is configured out of the box, you can simply plug in your internet cable and start using wireless

internet. We recommend you set up a password to secure your device, follow these steps.

Choose your powering solution, please see the section for possibilities.Powering

Connect your Internet cable to port 1, and local network devices to ports 2-5.

Set your computer IP configuration to (DHCP).

automatic

Wireless access point mode is enabled by default.

Connect your direct input power jack if not using POE, to start up the device.

The device will boot up and after a short beep Wireless network will be available for connecting.

Open network connections on your pc, mobile phone, or other device and search for MikroTik wireless network and connect to it.

Once connected to the wireless network, open in your web browser to start configuration, since there is no password by https://192.168.88.1

default, you will be logged in automatically .(or, for some models, check user and wireless passwords on the sticker) .

We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best

performance and stability,

Choose your country, to apply country regulation settings, and set up your password on the screen that loads.

Powering

The device accepts power from the power jack or from the first Ethernet port (Passive PoE). The power consumption for under maximum  RB951G-2HnD

load can reach 7 W,RB951Ui-2HnD24 W.

direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 8-30 V DC.

The first Ethernet port accepts passive Power over Ethernet accepts 8-30 V DC.

Produkt Specifikationer

Mærke:	Mikrotik
Kategori:	Adgangspunkt
Model:	RB951Ui-2HnD
Vekselstrømsindgangsspænding:	7 - 31 V
Bredde:	138 mm
Dybde:	113 mm
Højde:	29 mm
Produktfarve:	Hvid
Ethernet LAN-porte (RJ-45):	5
Antal USB 2.0-porte:	1
Driftstemperatur (T-T):	-20 - 50 °C
Ethernet LAN-datahastigheder:	10, 100 Mbit/s
Intern hukommelse:	128 MB
Husmateriale:	Plast
Strømforbrug (maks.):	7 W
Netværksstandarder:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3u
Modtager, følsomhed:	802.11g: -96dBm @ 6Mbit/s to -80dBm @ 54Mbit/s\r\n802.11n: -96dBm @ MCS0 to -78dBm @ MCS7
LED-indikatorer:	Ja
Harmoniseret systemkode (HS):	85176990
Antal brugere:	- bruger(e)
Processorfrekvens:	600 Mhz
Intern hukommelsestype:	DDR2
Medfølgende software:	MikroTik RouterOS
Frekvensbånd:	2.4 GHz
Intern:	Ingen
Maksimal dataoverførselshastighed:	- Mbit/s
Modulation:	16-QAM, 64-QAM, BPSK, CCK, DBPSK, DQPSK, DSSS, OFDM, QPSK
Processormodel:	Qualcomm Atheros AR9344-DC3A
Antenne type:	Intern
USB-stik type:	USB Type-A
Strøm over Ethernet (PoE):	Ja
Antal kanaler:	- kanaler
Indbygget processer:	Ja
2.4 GHz:	Ja
Niveau for antennestyrke (maks.):	2.5 dBi