Milwaukee 48-59-2002 Manual

Milwaukee Batterioplader 48-59-2002

Læs nedenfor 📖 manual på dansk for Milwaukee 48-59-2002 (2 sider) i kategorien Batterioplader. Denne guide var nyttig for 42 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

IMPORTANT SAFETY INSTRUCTIONS

WARNING

READ AND UNDERSTAND ALL INSTRUC-

TIONS. Failure to follow all instructions listed below,

may result in electric shock, re and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPER-

ATING INSTRUCTIONS FOR THE REDLITHIUM®

USB CHARG-

ER AND REDLITHIUM® USB BATTERIES.

2. CHARGE ONLY REDLITHIUM® USB BATTERIES IN THE

REDLITHIUM®

USB CHARGER. OTHER TYPES OF BATTERIES

MAY CAUSE PERSONAL INJURY AND DAMAGE.

3. BEFORE USING THE BATTERY AND CHARGER, READ THIS

OPERATOR’S MANUAL, YOUR TOOL OPERATOR’S MANUAL,

AND ALL LABELS ON THE BATTERY, CHARGER AND TOOL.

4. USE ONLY WITH LISTED/CERTIFIED ITE POWER SUPPLY. Others

may result in a risk of re, electric shock or personal injury.

5. AVOID DANGEROUS ENVIRONMENTS. Do not charge battery in

rain, snow, damp or wet locations. Do not use battery or charger in

the presence of explosive atmospheres (gaseous fumes, dust or am-

mable materials) because sparks may be generated when inserting

or removing battery, possibly causing re.

6. CHARGE IN A WELL VENTILATED AREA. Do not block charger

vents. Keep them clear to allow proper ventilation. Do not allow smok

ing or open ames near a charging battery. Vented gases may explode.

7. MAINTAIN CORD. When unplugging charger, pull plug rather than

cord to reduce the risk of damage to the electrical plug and cord. Never

carry charger by its cord. Keep cord from heat, oil and sharp edges.

Make sure cord will not be stepped on, tripped over or subjected to

damage or stress. Do not use charger with damaged cord or plug.

Have a damaged charger replaced immediately.

8. USE ONLY RECOMMENDED ATTACHMENTS. Use of an attachment

not recommended or sold by the battery charger or battery manu-

facturer may result in a risk of re, electric shock or personal injury.

9. TO REDUCE THE RISK OF ELECTRIC SHOCK, always unplug

charger before cleaning or maintenance.

10. DO NOT BURN OR INCINERATE BATTERY PACKS. Battery

may explode, causing personal injury or damage. Toxic fumes and

materials are created when battery are burned.

11. DO NOT CRUSH, DROP, OR DAMAGE battery. Do not use a bat-

tery or charger that has received a sharp blow, been dropped, run

over, or damaged in any way (e.g., pierced with a nail, hit with a

hammer, stepped on).

12. DO NOT DISASSEMBLE. Incorrect reassembly may result in the

risk of electric shock, re or exposure to battery chemicals. If it is

damaged, take it to a MILWAUKEE service facility.

13. BATTERY CHEMICALS CAUSE SERIOUS BURNS. Never allow

contact with skin, eyes, or mouth. If a damaged battery leaks battery

chemicals, use rubber or neoprene gloves to dispose of it. If skin is

exposed to battery uids, wash with soap and water and rinse with

vinegar. If eyes are exposed to battery chemicals, immediately ush

with water for 20 minutes and seek medical attention. Remove and

dispose of contaminated clothing.

14. DO NOT SHORT CIRCUIT. A battery pack will short circuit if a metal

object makes a connection between the positive and negative con-

tacts on the battery pack. Do not place a battery pack near anything

that may cause a short circuit, such as coins, keys or nails in your

pocket. Do not allow uids to ow into battery pack. Corrosive or

conductive uids, such as seawater, certain industrial chemicals,

and bleach or bleach containing products, etc., can cause a short

circuit. A short circuited battery pack may cause re, personal injury,

and product damage.

15. STORE YOUR BATTERY AND CHARGER in a cool, dry place. Do

not store battery where temperatures may exceed 120°F (50°C) such

as in direct sunlight, a vehicle or metal building during the summer.

READ AND SAVE ALL

INSTRUCTIONS FOR

FUTURE REFERENCE.

SPECIFICATIONS

Charger Cat. No. 48-59-2002

..............................................................

Input Volts .....................................................................................5 DC

Input Amps............................................................................0.1 - 2.1 A

Output Volts ..................................................................................4 DC

Output Amps ..................................................................................2.1A

REDLITHIUM® USB Batteries

Volts ..............................................................................................4 DC

Operating Temperature

Battery and Charger ..............................

40°F to 104°F (4°C to 40°C)

Battery and Tool .................................... 0

°F to 149°F (-18°C to 65°C)

Power Supply Cat. No. 44-66-1202

.......................................................

Wall Plug Input Volts ................................................................. 120 AC

SYMBOLOGY

Volts

Direct Current

Do not stare at the

operating light source

Read Operator's

Manual

Amps

Properly Recycle

Batteries

BFP Backfeed Protected

California Energy

Commission

BATTERY

WARNING

To reduce the risk of re, personal injury, and prod-

uct damage due to a short circuit, never immerse

your tool, battery pack or charger in uid or allow a uid to ow

inside them. Corrosive or conductive uids, such as seawater,

certain industrial chemicals, and bleach or bleach containing

products, etc., can cause a short circuit.

Maintenance and Storage

Do not expose your battery or cordless tools to water or rain, or allow

them to get wet. This could damage the tool and battery. Do not use

oil or solvents to clean or lubricate your battery. The plastic casing will

become brittle and crack, causing a risk of injury.

Store batteries at room temperature away from moisture. Do not store

in damp locations where corrosion of terminals may occur. As with other

battery types, permanent capacity loss can result if the pack is stored for

long periods of time at high temperatures (over 120° F). MILWAUKEE

Li-Ion batteries maintain their charge during storage longer than other

battery types. After about a year of storage, charge the battery as normal.

WARNING

To reduce the risk of injury or explosion, never burn

or incinerate a battery pack even if it is damaged,

dead or completely discharged. When burned, toxic fumes and

materials are created.

Disposing of MILWAUKEE Li-Ion Battery

MILWAUKEE Li-Ion batteries are more environmentally friendly than

some other types of power tool batteries. Always dispose of your battery

according to federal, state and local regulations. Contact a recycling

agency in your area for recycling locations.

Even discharged batteries contain some energy. Before disposing, use

electrical tape to cover the terminals to prevent the battery from shorting,

which could cause a re or explosion.

RBRC Battery Recycling Seals

The RBRC™ Battery Recycling Seals (see "Symbology") on your bat-

teries indicate that MILWAUKEE has arranged for the recycling of that

battery with the Rechargeable Battery Recycling Corporation (RBRC). At

the end of your battery's useful life, return the battery to a MILWAUKEE

Branch Oce/Service Center or the participating retailer nearest you.

For more information, visit the RBRC web site at www.rbrc.org.

REDLITHIUM® USB BATTERY AND CHARGER

PILE ET CHARGEUR USB REDLITHIUM®

BATERÍA USB Y CARGADOR REDLITHIUM®

CHARGER

WARNING

Charge only REDLITHIUM® USB batteries in the

REDLITHIUM®

USB charger. Other types of batteries

may cause personal injury and damage.

How to Charge the Battery Pack

1. Plug your USB cable into a power source such as an AC wall adaptor,

computer or car port.

2. Insert the micro USB into the micro USB port.

3. Twist the charger cap and pull out the charger bay.

4. Align the battery arrow with the charger arrow and insert the battery

completely.

5. Close the battery bay and twist the cap to lock.

6. The indicator light will display the charging status:

Red Flashing: Charging, 0-25% charged

Orange Flashing: Charging, 25-80% charged

Green Flashing: Charging, 80-99% charged

Green Solid: 99-100% Charged

Red/Green Flashing: Damaged or Faulty Battery

If the light indicator ashes red and green, check that the battery is fully

seated into the bay. Remove the battery and reinsert. If the light con-

tinues to ash red and green, the battery may be extremely hot or cold,

or wet. Allow the battery to cool down, warm up, or dry out and then

reinsert. If the problem persists, contact a MILWAUKEE service facility.

Fuel Gauge

When the charger is unplugged and a battery is inserted, the indicator

light will display the current battery charge:

Red Flashing: 0-10% remaining

Red Solid: 10-25% remaining

Orange Solid: 25-80% remaining

Green Solid: 80-100% remaining

WARNING

To reduce the risk of injury, always unplug the

charger and remove the battery from the charger

before performing any maintenance. The charger and battery have

no internal serviceable parts. Never disassemble the battery or

charger. Maintenance and Storage

Store your charger in a cool, dry place.

As a general practice, it is best to unplug battery chargers and remove

batteries when not in use. No battery damage will occur, however, if the

charger and battery are left plugged in.

WARNING

To reduce the risk of injury and damage, never im-

merse your battery or charger in liquid or allow a

liquid to ow inside them.

Cleaning

Clean out dust and debris from charger vents and electrical contacts

by blowing with compressed air. Use only mild soap and a damp cloth

to clean the battery and charger, keeping away from all electrical

contacts. Certain cleaning agents and solvents are harmful to plastics

and other insulated parts. Some of these include gasoline, turpentine,

lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia

and household detergents containing ammonia. Never use ammable

or combustible solvents around batteries, charger, or tools.

SERVICE - UNITED STATES

1-800-SAWDUST (1.800.729.3878)

Monday-Friday, 7:00 AM - 6:30 PM CST

or visit www.milwaukeetool.com

Contact Corporate After Sales Service Technical Support with technical,

service/repair, or warranty questions.

Email: metproductsupport@milwaukeetool.com

Become a Heavy Duty Club Member at www.milwaukeetool.com to

receive important notications regarding your tool purchases.

SERVICE - CANADA

Milwaukee Tool (Canada) Ltd

1.800.268.4015

Monday-Friday, 7:00 AM - 4:30 PM CST

or visit www.milwaukeetool.ca

LIMITED WARRANTY - USA & CANADA

Every MILWAUKEE REDLITHIUM USB battery and charger* is warranted to the original

purchaser only to be free from defects in material and workmanship. Subject to certain excep-

tions, MILWAUKEE will repair or replace repair a REDLITHIUM USB battery or charger which,

after examination, is determined by MILWAUKEE to be defective in material or workmanship

for a period of two (2) years after the date of purchase unless otherwise noted. Return of the

REDLITHIUM USB battery or charger to a MILWAUKEE factory Service Center location or

MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. For the

proper shipping procedure of battery packs, contact 1.800.SAWDUST (1.800.729.3878), or go

to www.milwaukeetool.com. A copy of the proof of purchase should be included with the return

product. This warranty does not apply to damage that MILWAUKEE determines to be from

repairs made or attempted by anyone other than MILWAUKEE authorized personnel, misuse,

alterations, abuse, normal wear and tear, lack of maintenance, or accidents.

Normal Wear: This warranty does not cover repair or replacement when normal use has ex-

hausted the life of a part including, but not limited to charging cables, and wall plugs.

*This warranty does not cover any cordless product sold with the REDLITHIUM USB battery

and/or charger. There are separate and distinct warranties available for these products.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED

HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MIL-

WAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD

NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR

ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY

COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A

CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT IN-

CLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS

WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRIT-

TEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY

IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE

EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRAN-

TIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS

DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN

IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS

WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER

RIGHTS WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the Find a Service Center Search in the Parts & Service section of MILWAU-

KEE’s website www.milwaukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate

your nearest MILWAUKEE factory Service Center location.

LIMITED WARRANTY - MEXICO, CENTRAL AMERICA

& CARIBBEAN

TECHTRONIC INDUSTRIES' warranty is for 2 years since the original purchase date.

This warranty card covers any defect in material and workmanship on this Product.

To make this warranty valid, present this warranty card, sealed/stamped by the distributor or

store where you purchased the product, to the Authorized Service Center (ASC). Or, if this card

has not been sealed/stamped, present the original proof of purchase to the ASC.

Call 55 4160-3547 to nd the nearest ASC, for service, parts, accessories or components.

Procedure to make this warranty valid

Take the product to the ASC, along with the warranty card sealed/stamped by the distributor

or store where you purchased the product, and any faulty piece or component will be replaced

without cost for you. We will cover all freight costs relative with this warranty process.

Exceptions

This warranty is not valid in the following situations

a) When the product is used in a dierent manner from the end-user guide or instruction manual.

b) When the conditions of use are not normal.

c) When the product was modied or repaired by people not authorized by TECHTRONIC

INDUSTRIES.

Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid

electric risks.

SERVICE AND ATTENTION CENTER

Call to 55 4160-3547

Model:

Date of Purchase:

Distributor or Store Stamp:

IMPORTED AND

COMMERCIALIZED BY

TECHTRONIC

INDUSTRIES MEXICO,

S.A. DE C.V.

Miguel de Cervantes

Saavedra No.301 Piso 5,

Torre Norte

11520 Colonia Ampliación

Granada

Miguel Hidalgo, Ciudad de

Mexico, Mexico

RÈGLES IMPORTANTES DE SÉCURITÉ

AVERTISSEMENT

LIRE ET COMPRENDRE TOUTES

LES INSTRUCTIONS. Le non-respect

des instructions ci-après peut entraîner des chocs électriques, des

incendies et/ou des blessures graves.

CONSERVER CES INSTRUCTIONS

1. CE MANUEL CONTIENT DES CONSIGNES DE SÉCURITÉ ET

LE MODE D’EMPLOI DU BLOC-PILES REDLITHIUM® AVEC

CHARGEUR USB ET REDLITHIUM® BLOC-PILES.

2. CHARGEZ UNIQUEMENT LE BLOC-PILES REDLITHIUM® USB

AVEC LE CHARGEUR USB REDLITHIUM®. LES PILES D’AUTRES

TYPES PEUVENT CAUSER DES DOMMAGES ET DES BLESSURES.

3. AVANT D’UTILISER LE BLOC-PILES ET LE CHARGEUR, LIRE LE

PRÉSENT MANUEL D’UTILISATION, LE MANUEL D’UTILISATION

DE VOTRE OUTIL, AINSI QUE TOUTES LES ÉTIQUETTES SE

TROUVANT SUR LE BLOC-PILES, LE CHARGEUR ET L’OUTIL.

4. UTILISER UNIQUEMENT UNE ALIMENTATION ÉLECTRIQUE RÉ-

PERTORIÉE ET CERTIFIÉE ITE. L’utilisation d’autres alimentations

peut causer un risque d’incendie, de choc électrique ou de blessure.

5. ÉVITER LES ENVIRONNEMENTS DANGEREUX. Ne pas charger le

bloc-piles sous la pluie, la neige, dans un endroit humide ou mouillé.

Ne pas utiliser le bloc-piles ou le chargeur dans un endroit propice à

la présence de matières explosives (fumées gazeuses, poussières

ou matériaux inflammables) car l’insertion ou le retrait du bloc-piles

pourrait alors créer des étincelles et entraîner un incendie.

6. CHARGER DANS UN ENDROIT BIEN VENTILÉ. Ne pas bloquer les

orifices d'aération du chargeur. S’assurer qu'ils ne sont pas obstrués

afin de permettre une ventilation appropriée. Ne pas fumer ou utiliser

des flammes nues à proximité d’un bloc-piles en charge. Les gaz

ventilés peuvent exploser.

7. ENTRETENIR LE CORDON DU CHARGEUR. Pour le débranche-

ment du chargeur, tirer sur la fiche plutôt que sur le cordon pour

réduire le risque de dommages à la prise ou au cordon électrique.

Ne jamais transporter le chargeur par son cordon. Garder le cordon

à l'écart de la chaleur, de l'huile et des objets tranchants. S’assurer

que le cordon n’est pas piétiné, accroché, endommagé ou malmené.

Ne pas utiliser le chargeur si le cordon ou la fiche est endommagé(e).

Remplacer immédiatement le chargeur s'il est endommagé.

8. UTILISER EXCLUSIVEMENT LES ACCESSOIRES RECOM-

MANDÉS. L’utilisation d’un accessoire non recommandé ou vendu

par le fabricant du chargeur ou du bloc-piles peut causer un risque

d’incendie, de choc électrique ou de blessure.

9. POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE, toujours dé-

brancher le chargeur avant de procéder à un nettoyage ou un entretien.

10. NE PAS

BRÛLER OU INCINÉRER LES BLOCS-PILES. Les blocs-piles

peuvent exploser, causant des dommages et des blessures. Des fumées

et des matières toxiques se dégagent des blocs-piles lorsqu'ils sont brûlés.

11. NE PAS ÉCRASER, LAISSER TOMBER OU ENDOMMAGER LE

BLOC-PILES. Ne pas utiliser un bloc-piles ou un chargeur qui a

reçu un choc violent, est tombé ou a été écrasé ou endommagé de

quelque façon que ce soit (p. ex., percé par un clou, frappé d’un

coup de marteau, piétiné).

12. NE PAS DÉSASSEMBLER LE PRODUIT. Un remontage incor-

rect peut entraîner des risques de choc électrique, d’incendie ou

d'exposition à des produits toxiques. En cas de dommage, confier

le produit à un centre de service MILWAUKEE.

13. LES PRODUITS CHIMIQUES DES BLOCS-PILES PROVOQUENT

DES BRÛLURES GRAVES. Éviter tout contact avec la peau, les

yeux ou la bouche. Si des produits chimiques fuient d'un bloc-piles

endommagé, porter des gants de caoutchouc ou en néoprène pour

le manipuler. Si la peau est exposée à du liquide du bloc-piles, laver

à l’eau et au savon et rincer avec du vinaigre. Si les yeux sont ex-

posés aux produits chimiques d'un bloc-piles, immédiatement rincer

abondamment à l'eau pendant 20 minutes et consulter un médecin.

Retirer et jeter au rebut les vêtements contaminés.

14. ATTENTION AUX COURTS-CIRCUITS! Un bloc-piles court-circuite

si un objet métallique établit une connexion entre les contacts positifs

et négatifs sur le bloc-piles. Ne placez pas un bloc-piles près de tout

ce qui peut causer un court-circuit, comme des pièces de monnaie,

des clés ou des clous dans votre poche. Ne pas laisser les uides

s’écouler dans le bloc-piles. Les uides corrosifs ou conducteurs,

tels que l’eau de mer, certains produits chimiques industriels, les

produits de blanchiment ou de blanchiment, etc., peuvent provoquer

un court-circuit. Un bloc-batterie court-circuité peut provoquer des

incendies, des blessures corporelles et des dommages au produit.

15. ENTREPOSER VOTRE BLOC-PILES ET CHARGEUR dans un

endroit frais et sec. Ne pas entreposer le bloc-piles dans des endroits

où la température peut dépasser 50 °C (120 °F), par exemple, un

endroit exposé directement à la lumière du soleil, un véhicule ou

une construction en métal pendant l’été.

LIRE ET CONSERVER

TOUTES LES INSTRUCTIONS

POUR RÉFÉRENCE FUTURE.

SPÉCIFICATIONS

Cat. de chargeur No 48-59-2002

.........................................................

Tension d’entrée ..........................................................................5 CD

Ampérage d’entrée .............................................................. 0,1 – 2,1 A

Tension de sortie ..........................................................................4 CD

Ampérage de sortie ..................................................................... 2,1 A

REDLITHIUM® Bloc-piles USB

Tension .........................................................................................4 CD

Température de fonctionnement

Bloc-piles et chargeur ..............................

4°C à 40°C (40°F à 104°F)

Bloc-piles et outil .........................

……….-18°C à 65°C (0°F à 149°F)

Cat. de suministro de energía No

.....................................

44-66-1202

Tension d’entrée de prise murale ............................................ 120 CA

PICTOGRAPHIE

Volts

Courant direct

No mire jamente

la fuente de luz

operativa

Lisez le manuel

de l’operateur

Ampères

Recyclage correct

des batteries

BFP Rétro-alimentation protégée

Commission de l’énergie

Commission

BLOC-PILES

AVERTISSEMENT

Pour réduire le risque d’incendie, de blessures

corporelles et de dommages causés par un

court-circuit, ne jamais immerger l’outil, le bloc-piles ou le chargeur

dans un liquide ou laisser couler un uide à l’intérieur de celui-ci. Les

uides corrosifs ou conducteurs, tels que l’eau de mer, certains pro-

duits chimiques industriels, les produits de blanchiment ou de blanchi-

ment, etc., peuvent provoquer un court-circuit.

Entretien et entreposage

Ne pas exposer votre bloc-piles ni vos outils sans l à l’eau ou la pluie,

ou les laisser prendre l'humidité. Cela pourrait endommager l’outil et le

bloc-piles. Ne pas utiliser d'huile ou solvants pour nettoyer ou lubrier

votre bloc-piles. Le boîtier du bloc-piles risque de devenir cassant ou

de se fendiller, causant un risque de blessure.

Entreposer les blocs-piles à température ambiante à l'abri de l’humidité.

Ne pas les entreposer dans un endroit humide où la corrosion des

bornes peut survenir. Comme pour d'autres types de batteries, une

perte permanente de capacité peut survenir si le bloc-piles est entre-

posé pendant longtemps à haute température (48°C/120°F). Les piles

Li-ion MILWAUKEE maintiennent leur charge pendant plus longtemps

que les autres types de piles. Après un an d'entreposage, rechargez le

bloc-piles comme d’habitude.

Produkt Specifikationer

Mærke:	Milwaukee
Kategori:	Batterioplader
Model:	48-59-2002

Har du brug for hjælp?

Hvis du har brug for hjælp til Milwaukee 48-59-2002 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Batterioplader Milwaukee Manualer

Milwaukee M12-18AC Manual

3 September 2024

Milwaukee M12-18C Manual

3 September 2024

Milwaukee 48-59-1202 Manual

15 August 2024

Milwaukee 48-59-1812 Manual

6 August 2024

Milwaukee 48-59-1204 Manual

1 August 2024

Milwaukee 48-59-0255 Manual

27 Juli 2024

Milwaukee 2510-20 Manual

6 Februar 2024

Milwaukee 48-59-1808 Manual

7 Januar 2024

Milwaukee 48-59-1806 Manual

21 Marts 2023

Milwaukee 48-59-1802 Manual

3 Marts 2023

Batterioplader Manualer

Nyeste Batterioplader Manualer

Hama 201634 Manual

21 December 2024

Hama 210290 Manual

21 December 2024

Hama 210594 Manual

21 December 2024

Nitecore FSP30 Manual

16 December 2024

Nitecore NES2000 Manual

16 December 2024

Nitecore FSP100 Manual

16 December 2024

Nitecore NC10000 Manual

16 December 2024

Nitecore NES500 Manual

16 December 2024

Nitecore NPS400 Manual

16 December 2024

Nitecore NPB1 Manual

16 December 2024