Monacor ESP-232/WS Manual

Monacor Højttaler ESP-232/WS

Læs gratis den danske manual til Monacor ESP-232/WS (3 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Monacor ESP-232/WS, eller vil du spørge andre brugere om produktet?

Side 1/3
®
ELA-Lautsprecherbox für
100-V- oder 8-Ω-Betrieb
Bitte lesen Sie diese Anleitung vor der Installation
gründlich durch und heben Sie sie für ein späteres
Nachlesen auf.
1 Verwendungsmöglichkeiten
Diese 2-Wege-Lautsprecherbox zur Wandmon-
tage ist speziell für den Einsatz in Beschallungsan-
lagen konzipiert. Sie ist mit einem Übertrager für
den Betrieb in 100-V-Anlagen ausgestattet, kann
aber auch direkt an einen niederohmigen Verstär-
kerausgang angeschlossen werden. Die Lautspre-
cherbox ist wetterfest (IP 55) und kann darum auch
im Außenbereich eingesetzt werden.
2 Wichtige Hinweise für den Gebrauch
Die Lautsprecherbox entspricht allen erforderli-
chen Richtlinien der EU und ist deshalb mit
gekennzeichnet.
G
Schützen Sie die Lautsprecherbox vor großer
Hitze und lte (zulässiger Einsatztemperaturbe-
reich 0 40°C).
GVerwenden Sie zum Reinigen nur ein trockenes,
oder angefeuchtetes, weiches Tuch, auf keinen
Fall aggressive Reinigungsmittel oder Chemi -
kalien.
GWird die Lautsprecherbox zweckentfremdet,
nicht fachgerecht montiert, falsch angeschlos-
sen oder überlastet, kann keine Haftung r
daraus resultierende Sach- oder Personenschä-
den und keine Garantie für die Lautsprecherbox
übernommen werden.
3 Installation
WARNUNG Beim Betrieb in 100-V-Anlagen liegt
berührungsgefährliche Spannung bis
100 V an der Lautsprecherleitung an.
Die Installation darf nur durch Fach-
personal erfolgen.
Achten Sie auf die Belastung des ELA-Verstärkers
durch die Lautsprecher. Eine Überlastung kann
den Verstärker beschädigen! Die Summe der
Leistungen aller angeschlossenen Lautsprecher
darf die Verstärkerleistung nicht überschreiten.
Soll die Lautsprecherbox endgültig aus
dem Betrieb genommen werden, überge-
ben Sie sie zur umweltgerechten Entsor-
gung einem örtlichen Recyclingbetrieb.
1) Vor der Installation der Lautsprecherbox den
ELA-Verstärker ausschalten, damit die Laut-
sprecherleitung spannungsfrei ist!
2) Zur Wandmontage den Montagebügel von der
Lautsprecherbox abschrauben und den Bügel
an ge wünschter Stelle der Wand befestigen.
3) Die gewünschte Nennbelastung (Lautstärke) mit
dem Schalter auf der Rückseite einstellen oder
beim Betrieb an einem niederohmigen
Verstärkerausgang den Schalter in
die Position „8 Ω“ drehen.
VORSICHT! In der Position „8Ω“ den Lautspre-
cher auf keinen Fall in einer 100-V-Anlage be -
treiben. Der Lautsprecher und eventuell auch
der Verstärker werden beschädigt.
4) Die Lautsprecherbox über die Anschlussklem-
men an den ELA-Verstärker anschließen. Beim
Anschluss von mehreren Lautsprechern darauf
achten, dass die Lautsprecher alle gleich gepolt
werden (z. B. schwarze Klemme = Minuspol).
5) Die Lautsprecherbox an dem Montagebügel
festschrauben und optimal auf den zu beschal-
lenden Bereich ausrichten.
Änderungen vorbehalten.
PA Speaker System for 100 V
Operation or 8 Ω Operation
Please read these operating instructions carefully
prior to the installation and keep them for later ref-
erence.
1 Applications
This 2-way speaker system for wall mounting is
especially designed for applications in PA systems.
It is equipped with a transformer for operation in
100 V systems, but it can also directly be con-
nected to a low-impedance amplifier output. The
speaker system is weatherproof (IP 55) and is
therefore also suitable for outdoor applications.
2 Important Notes
The speaker system corresponds to all required
directives of the EU and is therefore marked with .
GProtect the speaker system against excessive
heat and cold (admissible ambient temperature
range 0 40 °C).
GFor cleaning only use a soft cloth, dry or slightly
damp, never use aggressive detergents or
chemicals.
GNo guarantee claims for the speaker system and
no liability for any resulting personal damage or
material damage will be accepted if the speaker
system is used for other purposes than originally
intended, if it is not correctly installed or con-
nected, or if it is overloaded.
3 Installation
1) Prior to the installation of the speaker system
switch off the PA amplifier completely, so that
the speaker cable will not carry any voltage!
WARNING During operation, there is a hazard of
contact with a voltage of up to 100 V
at the speaker cable. The installation
must be carried out by skilled per-
sonnel only.
Observe the load of the PA amplifier by the speak-
ers. An overload may damage the amplifier! The
total power of all speakers connected must not
exceed the amplifier power.
If the speaker system is to be put out of
operation definitively, take it to a local
recycling plant for a disposal which is not
harmful to the environment.
2) For wall mounting, screw off the mounting
bracket from the speaker system and fix the
bracket at the desired place of the wall.
3) Adjust the desired rated load (volume) with the
switch on the rear side or turn the
switch to position “8 Ω” when operating
at a low-impedance amplifier output.
CAUTION! In position “8 Ω” never use the
speaker in a 100 V system. The speaker and
possibly the amplifier will be damaged.
4) Connect the speaker system via the connecting
terminals to the PA amplifier. When connecting
several speakers, make sure that all speakers
have the same polarity (e. g. black terminal =
negative pole).
5) Tightly screw the speaker system at the mount-
ing bracket and align it in an optimum way to the
area where the sound is to be directed.
Subject to technical modification.
ESP-232/SW Bestell-Nr. 16.2600
ESP-232/ WS Bestell-Nr. 16.2610
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 3628307 Bremen Germany
Copyright ©by MONACOR INTERNATIONAL. All rights reserved. A-1152.99.02.05.2011
®
D A CH
GB
Technische Daten Specifications ESP-232 /…
Nennbelastbarkeit bei 100-V-Betrieb Power rating with 100 V operation 30 /20 /10 / 5 WRMS
Belastbarkeit bei 8-Ω-Betrieb Rating with 8 Ω operation 50 WMAX/ 30 WRMS
Frequenzbereich Frequency range 75 20 000 Hz
Mittlerer Schalldruck (1 W/1 m) SPL (1 W/1 m) 89 dB
Gehäuseschutzart Protective class of housing IP 55
Abmessungen Dimensions 160 × 260 × 180 mm
Gewicht Weight 2,3 kg
®
Enceinte Public Adress
pour fonctionnement
100 V ou 8 Ω
Veuillez lire la présente notice avec attention avant
lʼinstallation et conservez-la pour pouvoir vous y
reporter ultérieurement.
1 Possibilités dʼutilisation
Cette enceinte 2 voies pour montage mural est
spécialement conçue pour une utilisation dans des
installations de sonorisation. Elle est dotée dʼun
transformateur pour fonctionnement dans des instal-
lations 100 V, elle peut également être directement
reliée à une sortie amplificateur basse impédance.
Lʼenceinte est protégée contre les intempéries
(IP 55) et peut donc être utilisée en extérieur.
2 Conseils importants dʼutilisation
Lʼenceinte répond à toutes les directives néces-
saires de lʼUnion européenne et porte donc le sym-
bole .
G
Protégez lʼenceinte dʼune chaleur élevée et du
froid (température ambiante admissible 0 40 °C).
GPour le nettoyage, utilisez uniquement un chiffon
sec ou légèrement humide, et doux, en aucun
cas de détergents agressifs ou produits chi-
miques.
G
Nous déclinons toute responsabilité en cas de
dommages matériels ou corporels résultants si
lʼenceinte est utilisée dans un but autre que celui
pour lequel elle a été conçue, si elle nʼest pas cor-
rectement montée ou branchée ou sʼil y a sur-
charge ; en outre, la garantie deviendrait caduque.
3 Installation
AVERTISSEMENT Pendant le fonctionnement, une
tension de contact dangereuse
jusquʼà 100 V est présente au
câble haut-parleur. Seul un per-
sonnel qualifié peut effectuer
lʼinstallation.
Faites attention à la charge de lʼamplificateur PA
par les haut-parleurs. Une surcharge peut en -
dommager lʼamplificateur. La somme des puis-
sances de lʼensemble des enceintes reliées ne
doit pas dépasser la puissance de lʼamplificateur.
Lorsque lʼenceinte est définitivement reti-
rée du service, vous devez la déposer dans
une usine de recyclage adaptée pour
contribuer à son élimination non polluante.
1) Avant dʼinstaller lʼenceinte, éteignez lʼamplifica-
teur Public Adress pour que le câble haut-par-
leur ne soit pas porteur de tension !
2) Pour un montage mural, dévissez lʼétrier de
montage de lʼenceinte et fixez lʼétrier à lʼendroit
voulu sur le mur.
3) Réglez la puissance nominale souhaitée
(volume) avec interrupteur sur la face arrière
ou, pour un fonctionnement à une
sortie ampli basse impédance, tour-
nez le sélecteur sur la positon “8 Ω”.
ATTENTION ! En position “8 Ω”, ne faites pas
fonctionner lʼenceinte dans une installation
100 V. Lʼenceinte, voire lʼamplificateur, pour-
raient être endommagés.
4) Reliez lʼenceinte via les bornes à pinces à lʼam-
plificateur Public Adress. Si vous branchez plu-
sieurs enceintes, veillez à ce quʼelles aient
toutes la même polarité (par exemple pince
noire = pôle moins).
5) Vissez lʼenceinte sur lʼétrier de montage et
orientez-le de manière optimale vers la zone à
sonoriser.
Tout droit de modification réservé.
Cassa acustica PA
per 100 V o 8 Ω
Vi preghiamo di leggere attentamente le presenti
istruzioni prima dellʼinstallazione e di conservarle
per un uso futuro.
1 Possibilità dʼimpiego
Questa cassa acustica a 2 vie per montaggio alla
parete è stata realizzata specialmente per lʼimpiego
in impianti di sonorizzazione. È equipaggiata con un
trasformatore per il funzionamento in impianti con
uscita audio 100 V, ma può essere collegata anche
con unʼuscita a bassa impedenza dellʼamplificatore.
La cassa è resistente alle intemperie (IP 55), e per-
tanto può essere impiegata anche allʼesterno.
2 Avvertenze importanti per lʼuso
La cassa acustica è conforme a tutte le direttive
richieste dellʼUE e pertanto porta la sigla .
GProteggere la cassa acustica da alto calore
e freddo (temperatura dʼimpiego ammessa fra
0 e 40 °C).
GPer la pulizia usare solo un panno morbido,
asciutto o inumidito; non impiegare in nessun
caso detergenti aggressivi o prodotti chimici.
G
Nel caso dʼuso improprio, di montaggio sbagliato,
di collegamento scorretto o di sovraccarico della
cassa acustica, non si assume nessuna respon-
sabilità per eventuali danni consequenziali a per-
sone o a cose e non si assume nessuna garan-
zia per la cassa acustica.
3 Installazione
AVVERTIMENTO Durante il funzionamento in im -
pianti a 100 V, nel cavo per alto-
parlanti è presente una tensione
fino a 100 V, pericolosa in caso di
contatto. Lʼinstallazione deve es -
sere eseguita solo da personale
specializzato.
Tener presente anche il carico dellʼamplificatore
PA da parte degli altoparlanti. Un sovraccarico
può danneggiare lʼamplificatore! La somma delle
potenze di tutti gli altoparlanti collegati non deve
superare la potenza dellʼamplificatore.
Se si desidera eliminare la cassa acustica
definitivamente, consegnarla per lo smal-
timento ad unʼistituzione locale per il rici-
claggio.
1) Prima dellʼinstallazione della cassa acustica, spe-
gnere lʼamplificatore PA perché la linea per alto-
parlanti sia completamente esente da tensione!
2) Per il montaggio alla parete svitare la staffa di
montaggio dalla cassa e fissare la staffa nel
punto desiderato della parete.
3) Con il selettore sul retro impostare la potenza
nominale (il volume) richiesta oppure, in caso di
collegamento con unʼuscita a bassa
impedenza dellʼamplificatore, girare il
selettore in posizione “8 Ω”.
ATTENZIONE! In posizione “8 Ω”, non usare in
nessun caso lʼaltoparlante in un impianto con
uscita audio 100 V. Lʼaltoparlante e eventual-
mente anche lʼamplificatore subiranno dei danni.
4) Collegare la cassa acustica con lʼamplificatore
PA per mezzo dei morsetti di collegamento. Col-
legando più altoparlanti, fare attenzione affinché
tutti abbiano la stessa polarità (p. es. conduttore
nero = polo negativo).
5) Avvitare la cassa alla staffa di montaggio e
orientarla in modo ottimale verso la zona da
sonorizzare.
Con riserva di modifiche tecniche.
ESP-232/SW Bestell-Nr. 16.2600
ESP-232/ WS Bestell-Nr. 16.2610
MONACOR INTERNATIONAL GmbH & Co. KGZum Falsch 36 28307 Bremen • Germany
Copyright ©by MONACOR INTERNATIONAL. All rights reserved. A-1152.99.02.05.2011
®
F
I
B CH
Caractéristiques techniques Dati tecnici ESP-232 /…
Puissance nominale pour fonctionnement 100 V
Potenza nominale con 100 V 30 /20 /10 / 5 WRMS
Charge admissible pour fonctionnement 8 Ω Potenza con 8 Ω 50 WMAX/ 30 WRMS
Bande passante Gamma di frequenze 75 20 000 Hz
Pression sonore moyenne (1 W/1m) Pressione sonora media (1 W/1 m) 89 dB
Classe de protection du boîtier Grado di protezione del contenitore IP 55
Dimensions Dimensioni 160 × 260 × 180 mm
Poids Peso 2,3 kg


Produkt Specifikationer

Mærke: Monacor
Kategori: Højttaler
Model: ESP-232/WS
Vekselstrømsindgangsspænding: 100 V
Bredde: 160 mm
Dybde: 180 mm
Højde: 260 mm
Vægt: 2300 g
Produktfarve: Hvid
Udgangseffekt (RMS): 30 W
Equalizer: Ingen
Driftstemperatur (T-T): -20 - 50 °C
Husmateriale: Aluminium, Plastic
Anbefalet brug: DJ
Frekvensområde: 75 - 20000 Hz
Impedens: 8 ohm (Ω)
Forbindelsesteknologi: Ledningsført
Højttaler, type: 2-vejs
Lyd-output kanaler: 1.0 kanaler
Højttaler, placering: Kan monteres på væggen
Antal drivere: 1
Driver diameter: 130 mm
Diskanthøjttaler: Ja
Peak Music-Udgangseffekt (PMPO): 50 W
Sensitivitet: 89 dB
Egnet til udendørs brug: Ja

Har du brug for hjælp?

Hvis du har brug for hjælp til Monacor ESP-232/WS stil et spørgsmål nedenfor, og andre brugere vil svare dig