Moxa OnCell G3110-HSPA Manual

Moxa Ikke kategoriseret OnCell G3110-HSPA

Læs nedenfor 📖 manual på dansk for Moxa OnCell G3110-HSPA (172 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/172

OnCell G3100 Series User’s Manual

Edition 6 8.1, August 201

www.moxa.com/product

OnCell G3100 Series User’s Manual

The software described in this manual is furnished under a license agreement and may be used only in accordance with

the terms of that agreement.

Trademarks

The MOXA logo is a registered trademark of Moxa Inc.

All other trademarks or registered marks in this manual belong to their respective manufacturers.

Disclaimer

Information in this document is subject to change without notice and does not represent a commitment on the part of

Moxa.

Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited

to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the

products and/or the programs described in this manual, at any time.

Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for

its use, or for any infringements on the rights of third parties that may result from its use.

This product might include unintentional technical or typographical errors. Changes are periodically made to the

information herein to correct such errors, and these changes are incorporated into new editions of the publication.

Technical Support Contact Information

www.moxa.com/support

Moxa Americas

Toll

- 1- - - free: 888 669 2872

Tel:

- - - +1 714 528 6777

Fax:

- -5 -+1 714 28 6778

Moxa China (Shanghai office)

Toll

- - - free: 800 820 5036

Tel:

- - - +86 21 5258 9955

Fax:

- - -+86 21 5258 5505

Moxa Europe

Tel:

- - -0 +49 89 3 70 03 99

Fax:

- - -+49 89 3 70 03 99 99

Moxa Asia

-Pacific

Tel:

-2- - +886 8919 1230

Fax:

-2- -+886 8919 1231

Moxa India

el: - - - +91 80 4172 9088

Fax:

- - -+91 80 4132 1045

Table of Contents

1. Introduction ...................................................................................................................................... 1-1

Overview ........................................................................................................................................... 1-2

Package Checklist ............................................................................................................................... 1-2

Product Features ................................................................................................................................ 1-3

P roduct Specifications ......................................................................................................................... 1-3

DoC (Declaration of Conformity) ........................................................................................................... 1-5

Federal Communication Commission Interference Statement ............................................................ 1-5

OnCell G3100 Series Supporting Information .................................................................................. 1-5

FCC Radiation Exposure Statement ................................................................................................ 1-6

2. Getting Started ................................................................................................................................. 2-1

Panel Layout ...................................................................................................................................... 2-2

Connecting the Hardware 2-3....................................................................................................................

Wiring Requirements 2-4...................................................................................................................

SIM Card Installation ................................................................................................................... 2-4

Connecting the Power .................................................................................................................. 2-5

Connecting the I/O Port ............................................................................................................... 2-5

Connecting to the Network ........................................................................................................... 2-6

Connecting to a Serial Device 2-6.......................................................................................................

Connecting to the Ethernet Device ................................................................................................. 2-6

Adjustable Pull High/Low Resistors for the RS-485 Port (f 232/422/485 models)or RS- ......................... 2-6

LED Indicators ............................................................................................................................ 2-8

Reset Button ............................................................................................................................... 2-9

3. Initial IP Address Configuration ........................................................................................................ 3-1

Static and Dynamic IP Addresses .......................................................................................................... 3-2

Factory Default IP Address ................................................................................................................... 3-2

Configuration Options .......................................................................................................................... 3-2

OnCell Search Utility .................................................................................................................... 3-2

Web Console ............................................................................................................................... 3-2

ARP ........................................................................................................................................... 3-2

Telnet Console 3-3............................................................................................................................

Serial Console ............................................................................................................................. 3-7

4. Introducing Serial Port Operation Modes .......................................................................................... 4-1

Overview ........................................................................................................................................... 4-2

Device Control Applications .................................................................................................................. 4-2

Real COM and Secure Real COM Modes .......................................................................................... 4-2

Types of Real COM Connection ...................................................................................................... 4-3

Reverse Real COM and Secure Reverse Real COM Modes .................................................................. 4-4

Types of Reverse Real COM Connection .......................................................................................... 4-4

RFC 2217 Mode ........................................................................................................................... 4-5

Socket Applications ............................................................................................................................. 4-5

TCP Server and Secure TCP Server Modes ...................................................................................... 4-5

Types of TCP Server Connection .................................................................................................... 4-6

TCP Client and Secure TCP Client Modes ......................................................................................... 4-7

Types of TCP Client Connection ..................................................................................................... 4-7

UDP Mode .................................................................................................................................. 4-8

Types of UDP Connection .............................................................................................................. 4-8

Ethernet Modem Mode ......................................................................................................................... 4-9

SMS Tunnel Mode ............................................................................................................................... 4-9

Disabled Mode .................................................................................................................................... 4-9

5. Introducing OnCell Central Manager and Ethernet Operation Modes ................................................. 5-1

OnCell Central Management Software 5-2...................................................................................................

OnCell Central Serial Device Connection ......................................................................................... 5-2

OnCell Central Ethernet Device Connection ..................................................................................... 5-3

Cellular- Enabling Ethernet Device ......................................................................................................... 5-3

Virtual Modem Mode ........................................................................................................................... 5-4

6. Using the Web Console ...................................................................................................................... 6-1

Using Your Web Browser...................................................................................................................... 6-2

Browser Cookie Settings............................................................................................................... 6-2

Trusted Site Settings 6-3...................................................................................................................

Opening the Web Console ............................................................................................................. 6-4

Web Console Navigation ...................................................................................................................... 6-5

Basic Settings .................................................................................................................................... 6-6

Server Settings ........................................................................................................................... 6-6

Time Settings 6-6.............................................................................................................................

Network Settings ................................................................................................................................ 6-7

Basic Network Settings ................................................................................................................ 6-7

Host Table ................................................................................................................................ 13-4

System Log Settings .................................................................................................................. 13-5

Virtual Server Settings ............................................................................................................... 13-6

Auto Warning Settings ....................................................................................................................... 13-7

Event Settings .......................................................................................................................... 13-7

Serial Event Settings ................................................................................................................. 13-8

E- mail Alert .............................................................................................................................. 13-9

SNMP Trap ................................................................................................................................ 13-9

SMS Alert ............................................................................................................................... 13 10-

Customized SMS ..................................................................................................................... 13 10-

Remote Management ...................................................................................................................... 13 10-

Remote SMS Control ................................................................................................................ 13 10-

Manual SMS ............................................................................................................................ 13 11-

Remote Caller ID ..................................................................................................................... 13 12-

Maintenance .................................................................................................................................. 13 12-

Console Settings ..................................................................................................................... 13 12-

Ping ....................................................................................................................................... 13 12-

Firmware Upgrade ................................................................................................................... 13 13-

Configuration Import/Export ..................................................................................................... 13 13-

Load Factory Defaults .............................................................................................................. 13 14-

Change Password .................................................................................................................... 13 14-

Certificate ...................................................................................................................................... 13 15-

Ethernet SSL Certificate Import ................................................................................................. 13 15-

Certificate/Key Delete .............................................................................................................. 13 15-

System Monitoring .......................................................................................................................... 13 15-

Serial to Network Connections .................................................................................................. 13 15-

Serial Port Status .................................................................................................................... 13 16-

Serial Port Error Count ............................................................................................................. 13 16-

Serial Port Settings .................................................................................................................. 13 16-

Chipher Usage Status .............................................................................................................. 13 16-

System Status ................................................................................................................................ 13 17-

Serial Data Log ....................................................................................................................... 13 17-

System Log ............................................................................................................................ 13 17-

Dout State .............................................................................................................................. 13 18-

DIN and Power Status .............................................................................................................. 13 18-

Network Status .............................................................................................................................. 13 19-

Network Connections ............................................................................................................... 13 19-

Network Statistics ................................................................................................................... 13 19-

Routing .................................................................................................................................. 13 19-

DHCP Client List ...................................................................................................................... 13 20-

Internet Sessions List .............................................................................................................. 13 20-

Save Configuration ......................................................................................................................... 13 21-

Restart .......................................................................................................................................... 13 21-

Restart System ....................................................................................................................... 13 21-

Restart Ports ........................................................................................................................... 13 21-

14. Software Installation/Configuration ............................................................................................... 14-1

Overview ......................................................................................................................................... 14-2

Windows Driver Manager ................................................................................................................... 14-2

Installing Windows Driver Manager .............................................................................................. 14-2

Using Windows Driver Manager ................................................................................................... 14-5

OnCell Search Utility ....................................................................................................................... 14 13-

Installing OnCell Search Utility .................................................................................................. 14 13-

Configuring OnCell Search Utility ............................................................................................... 14 15-

Moxa OnCell Linux Real TTY Driver.................................................................................................... 14 18-

Basic Procedure ...................................................................................................................... 14 18-

Hardware Setup ...................................................................................................................... 14 19-

Installing Linux Real TTY Driver Files .......................................................................................... 14 19-

Mapping TTY Ports ................................................................................................................... 14 19-

Removing Mapped TTY Ports ..................................................................................................... 14 20-

Removing Linux Driver Files ...................................................................................................... 14 20-

Moxa OnCell UNIX Fixed TTY Driver .................................................................................................. 14 20-

Installing the UNIX Driver......................................................................................................... 14 20-

Configuring the UNIX Driver ..................................................................................................... 14 21-

A. Pinouts and Cable Wiring .................................................................................................................. A-1

Port Pinout Diagrams .......................................................................................................................... A-2

RS-232 (male DB9) Pinouts .......................................................................................................... A-2

4W/2W RS-485/RS-422 (Terminal Block) Pinouts ............................................................................ A-2

Power Input and Relay Output Pinouts ........................................................................................... A-2

Cable Wiring Diagrams ........................................................................................................................ A-3

Serial Cables A-3..............................................................................................................................

Pin Assignments for DB9 and DB25 Connectors ............................................................................... A-4

B. RFC2217 ............................................................................................................................................ B-1

C. Dynamic Domain Name Server .......................................................................................................... C-1

Overview ........................................................................................................................................... C-1

Configuration ..................................................................................................................................... C-2

D. Well Known Port Numbers ................................................................................................................ D-1

E. Auto IP Report Protocol .................................................................................................................... E-1

F. GSM Alphabet .................................................................................................................................... F-1

G. Default Settings ................................................................................................................................ G-1

1. Introduction

The OnCell G3100 series of cellular IP gateways have many exceptional features. Cellular IP gateways give you

an easy way to connect your serial and Ethernet devices to cellular mobile networks. Different models of the

OnCell G3100 series differ from their supported cellular standard and serial interface type. For example, OnCell

G3110 is a GRPS IP gateway with RS-232 serial interface while OnCell G3150-HSPA is a HSPA IP gateway with

RS- 232/422/485 serial interface.

The following topics are covered in this chapter:





Overview





Package Checklist





Product Features





Product Specifications





DoC (Declaration of Conformity)

 Federal Communication Commission Interference Statement

 OnCell G3100 Series Supporting Information

 FCC Radiation Exposure Statement

OnCell G3100 Series Introduction

1-2

Overview

The OnCell G3100, which can be used to connect any serial device and Ethernet device to a cellular network,

supports a number of different operation modes. The serial ports OnCell riverCOM d ’turns the OnCell G3100 s

into virtual COM ports that allow you to communicate with your serial devicesand Ethernet remotely over the

cellular network. The OnCell G3100 comes pre-installed with the TCP/IP protocol suite to transmit data back

and forth between the serial and Ethernet device and GPRS/EDGE or UMTS/HSPA TCP/IP network.

The OnCell G3100 functions as a router to achieve Ethernet to cellular connectivity. All Ethernet devices

connected to the OnCell’s LAN port are hidden from public view via the OnCell’s NAT function.

The OnCell G3100 also supports Secure TCP Server, Secure TCP Client, Secure Real COM, and Secure Reverse

Real COM modes for security critical applications, such as access control, and remote site management.

The OnCell G3100 also comes with a built-in relay output that can be configured to indicate the priority of

events when notifying or , warning engineers in the field and the two digital inputs allow you to connect basic

I/O devices, such as sensors, to the cellular network.

For some applications, serial data must be delivered reliably even if communication is disrupted. The OnCell

G3100 provides a powerful function to ensure that serial data is buffered in case of a communication failure.

When a communication failure occurs, the serial munication is data is buffered in the OnCell G3100 until com

resumed, at which point the buffered data is sent to its destination.

Package Checklist

Each OnCell G3100 serial and Ethernet cellular IP gateway is shipped in a separate box with standard

accessories. In addition, several optional accessories can be ordered separately. When you receive your

shipment, please check the contents of the box carefully, and notify your Moxa sales representative if any of

the items are missing or appear to be damaged.

OnCell G3100 Series cellular are shipped with the following items:IP gateways

Standard Accessories

• R l - - -1 - : ubber SMA antenna (OnCell G3100 mode name: ANT CQB ASM , OnCell G3100 HSPA model name

ANT- - - WCDMA ASM 1.5)

• -r k Din ail it

• 5- t b s pin erminal lock ( crew type)

• - t b s 10 pin erminal lock ( crew type)

• i g Quick nstallation uide (printed)

• Warranty card

Optional Accessories

• Power Adaptor: 1.2 A (or above) @ 12 V

• p s DC ower upply

• Power jack to terminal block cable

• - a Quad band GSM/GPRS/EDGE ntennas for OnCell G3110/G3150 series

(impedance = 50 ohms):

ANT- -AHSM- - CQB 00 3m: Omni 0dBi/10cm, magnetic SMA antenna, 3 m

ANT- -AHSM- - CQB 03 3m: Omni 3dBi/25cm, magnetic SMA antenna, 3 m

ANT- -AHSM- - CQB 05 3m: Omni 5dBi/37cm, magnetic SMA antenna, 3 m

• - - - Five band GSM/GPRS/EDGE/HSPA antennas for OnCell G3110/G3150 HSPA series (impedance = 50

ohms):

ANT- -AHSM- - WCDMA 04 2.5m: Omni directional, 4dBi/11cm, magnetic SMA antenna, 2.5 m

OnCell G3100 Series Introduction

1-3

Product Features

All models in the OnCell G3100 series have the following features:

• - Quad band 900/1800, 850/1900 MHz GSM/GPRS/EDGE

• - Five band UMTS/HSPA 800/850/AWS/1900/2100 MHz (OnCell G3100- HSPA only)

• Special design for Japan Softbank (JPS) or NTTDocomo (JPN) operator

• Versatile operation modes, including Real COM, Reverse Real COM, RFC2217, TCP Server, TCP Client, UDP,

Ethernet Modem and SMS Tunnel,

• AT command over Ethernet

• Private IP management software

• Port buffering function to prevent loss of serial data when communication is disrupted

• R Secure data access modes including Secure eal COM, Secure Reverse Real COM, Secure TCP Client, and

Secure TCP Server

• b Adjustable audrate feature for easy configuration of custom baudrates

• s Redundant DC power input

• LED indicators for status and signal level

• 2 digital inputs and 1 relay output

• GuaranLink for reliable connection

• Remote command by SMS

Product Speciﬁcations

Note: The OnCell G3100 series has several hardware revisions. Please check the following table to

see which functions are supported by the various revisions.

For Ethernet to Cellular, refer chapter 9 for or Virtual Modem Mode, refer chapter 10 for Fdetails.

details.

OnCell Central

Manager

Ethernet Device

<- > Cellular

Virtual Modem Mode

IP Gateway

OnCell G3110 Rev 1.2  – –

OnCell G3150 Rev 1.2  – –

OnCell G3110 Rev 2.0   

OnCell G3150 Rev 2.0   

OnCell G311 30 Rev .0   

OnCell G3150 Rev 3 .0   

OnCell G3110- HSPA Rev 1.0 



–

OnCell G3150- HSPA Rev 1.0   –

OnCell

G3110/G3150

OnCell

G3110/G3150- HSPA

LAN Interface

Ethernet 10/100 Mbps, RJ45 connector

Protection - Built in 1.5 KV magnetic isolation

Cellular Interface

Standard

Compliance

GSM/GPRS/EDGE GSM/GPRS/EDGE/UMTS/HSPA

Band Selection Quad-band 850/900/1800/1900

MHz

Five- band 800/850/AWS/1900/2100 MHz

Quad band- 850/900/1800/1900 MHz

OnCell G3100 Series Introduction

1-4

OnCell

G3110/G3150

OnCell

G3110/G3150- HSPA

Tx Power 1 watt GSM1800/1900,

2 watt EGSM850/900

1 watt GSM1800,

2 watt GSM900,

0.25 watt UMTS/HSPA,

0.5 watt EDGE900,

0.4 watt EDGE1800

GPRS Multi-slot

class

12 12

GPRS Mobile

Station Class

Class B

EDGE Multi-slot

class

12 12

EDGE Mobile

Station Class

Class B

GPRS Coding

Schemes

CS1 to CS4

SIM Control 3V

Serial Interface

No. of Ports 1

ESD Protection 15 KV

Serial Standards -G3110/G3110: RS 232 (DB9 male connector)

G3150/G3150: RS 422/485 (5- -232 (DB9 male connector), RS -pin terminal block

connector)

Serial Communication Parameters

Parity None, Even, Odd, Space, Mark

Data Bits 5, 6, 7, 8

Stop Bit(s) 1, 1.5, 2 (when parity = None)

Flow Control RTS/CTS, XON/XOFF

Speed 50 bps to 921.6 Kbps

Serial Signals

RS- 232 TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND

RS- -422 Tx+, Tx , Rx+, Rx , GND-

RS- - -485 4w Tx+, Tx , Rx+, Rx , GND-

RS- - - 485 2w Data+, Data , GND

I/O Interface

Alarm Contact 1 relay output with current carrying capacity of 1A@24 VDC

Digital Input 2 inputs electrically isolated from the electronics

+13 to +30 V for state “1” (On)

+3 to - 30 V for state “0” (Off)

Software Features

Network Protocols ICMP, TCP/IP, UDP, DHCP, Telnet, DNS, SNMP, HTTP, SMTP, HTTPS, SNTP, ARP, SSL

Operation Modes Real COM, Reverse Real COM, TCP Server, TCP Client, UDP, RFC2217, Ethernet Modem,

SMS Tunnel

Secure Operation

Modes

Secure Real COM, Secure Reverse Real COM, Secure TCP Client, Secure TCP Server

Configuration and

Management

Options

SNMP MIB II, SNMP Private MIB, SNMPv1/- v2c/v3, DDNS, IP Report, Web/Telnet/Serial

Console/SSH

Authentication - Local user name and password

Security Accessible IP list

Utilities Provided for Windows 95/98/ME, Windows NT, Windows

2000/XP/2003/Vista/Server-2008, Windows XP/2003/Vista/ Server 8 x64 Edition-200

OnCell G3100 Series Introduction

1-5

OnCell

G3110/G3150

OnCell

G3110/G3150- HSPA

Windows Drivers Windows 95/98/ME,Windows NT, Windows

2000/XP/2003/Vista/Server 2008, Windows

XP/2003/Vista/Server 2008 x64 Edition

Fixed TTY Drivers

SCO Unix, SCO OpenServer 5, SCO OpenServer 6, UnixWare 7, SVR4.2, QNX 4.25, QNX

6, Solaris 10, FreeBSD 5, FreeBSD 6

Real TTY Drivers Linux kernels 2.2.x, 2.4.x, 2.6.x

Physical Characteristics

Input Voltage 12 to 48 VDC

Data Link 585 to 900 mA (peak) @ 12 V

Power EFT/Surge

Protection

2 KV

Environmental Limits

Operating

temperature

- -30 to 55°C ( 22 to 131°F), 5 to 95% RH

- - 30 to 70°C ( 22 to 158°F), 5 to 95% RH (Wide temperature models only)

Storage

temperature

- -40 to 75°C ( 40 to 167°F)

Regulatory Approvals

EMC CE: EN55022 Class A/EN55024

FCC: FCC part 15 subpart B, Class A

Safety -1 UL60950

Warranty 5 years

DoC (Declaration of Conformity)

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one of the following measures:

OnCell G3100 Series Supporting Information

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example – use only shielded interface cables when connecting

to computer or peripheral devices). Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not

be co-located or operated in conjunction with any other antenna or transmitter.

OnCell G3100 Series Introduction

1-6

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your

body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

2. Getting Started

This chapter covers the hardware installation of the . Software installation is covered in the next OnCell G3100

chapter.

The following topics are covered in this chapter:





Panel Layout





Connecting the Hardware

 Wiring Requirements

 SIM Card Installation

 Connecting the Power

 Connecting the I/O Port

 Connecting to the Network

 Connecting to a Serial Device

 Connecting to the Ethernet Device

 L R s - f - ) Adjustable Pull High/ ow esistor for the RS 485 Port ( or RS 232/422/485 models

 LED Indicators

 Reset Button

OnCell G3100 Series G etting Started

2-3

Rear View

Side Views

Connecting the Hardware

This section describes how to connect the OnCell G3100 cellular IP gateway to a host PC or serial/Ethernet

devices for first time testing purposes. We cover topics such as: Wiring Requirements, SIM Installation,

DIN- n , Rail Mounting, Connecting the Power, Connecting to a Serial Device, Connecting to a Ethernet Device

Adjustable Pull High/Low Resistors for the RS- , 485 Port and LED Indicators.

OnCell G3100 Series G etting Started

2-4

Wiring Requirements

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or wiring your device. The OnCell

G3100 should be

secured at one location.

Wiring Caution!

Calculate the maximum poss

ible current in each power wire and common wire. Observe all

electrical codes

dictating the maximum current allowable for each wire size. If the current goes

above the maximum ratings,

the wiring could overheat, causing serious damage to your equipment.

mperature Caution!

Be careful when handling the device. When plugged in, the device’s internal components

generate heat, and

consequently the casing may feel hot to the touch.

You should also follow the guidelines : below

• Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must

cross, make sure the wires are perpendicular at the intersection point.

NOTE: Do not run signal or communication wiring and power wiring in the same wire conduit. To

avoid interference, wires with different signal characteristics should be routed separately.

• Use the type of signal transmitted through a wire to determine which wires should be kept separate. The

rule of thumb is that wiring that shares similar electrical characteristics can be bundled together.

• Keep input wiring and output wiring separate.

• Where necessary, it is advisable to label the wiring to all devices in the system.

SIM Card Installation

In order to protect the SIM card, the SIM card slot is located inside the OnCell G3100’s casing. You will need to

unscrew and remove the outer SIM card cover before installing or removing the SIM card.

Follow these steps to remove or install the SIM card:

1. Remove the screw holding the outer SIM card cover.

2. Push the outer SIM card cover to the left to remove it.

3. R otate it upwards to expose the SIM card slot.

(a) Remove the SIM card from the SIM card slot, or

(b) Insert the SIM card into the SIM card slot.

4. Reverse the above steps to replace the outer SIM card cover.

OnCell G3100 Series G etting Started

2-5

ATTENTION

If the

IP gateway is in GSM/GPRS mode, SIGNAL LEDs will not be illuminated if the phone number or APN is

incorrect. Check the GSM LED if the SIM card is installed correctly

The

GSM LEDs on the front panel provide a convenient way of checking if the

SIM card is installed properly. If

the antenna is installed and the network is operating normally, then at least one of the three SIGNAL LEDs

should be illuminated at all times. If none of the

GSM and SIGNAL LEDs are illuminated, then the SIM

card may

not be installed properly. This is because the PIN code is stored on the SIM card; if the PIN code cannot be

accessed, then the IP gateway will not be accessible over the network.

Connecting the Power

The dual power inputs that connect to the 4-pin power terminal block (2 terminals per power input) can be used

to connect the OnCell G3100 to a variety of field power sources that support 12 to 48 VDC. After connecting the

power wire to the OnCell G3100’s terminal block, t he “PWR” LED will glow a solid green color to indicate that the

system is ready.

Connecting the I/O Port

Six terminals on the terminal block are reserved for the I/O ports , with 2 terminals used for each input, and 2

terminals used for the output.

Digital Input

Digital ON and OFF determine which of the 2 electrically isolated inputs are used:

• +13 to +30 V for state “1” (On)

• - +3 to 30 V for state “0” (Off)

OnCell G3100 Series G etting Started

2-6

Digital Output: 1 relay output with current carrying capacity of 1A @ 24 VDC

Power Status Event Relay

Off No Open

On n Yes Ope

No Short

Connecting to the Network

Connect one end of the Ethernet cable to the OnCell G3100's 10/100M Ethernet port and the other end of the

cable to the Ethernet network.

If the cable is properly connected, the OnCell G3100 will indicate a valid connection to the Ethernet as follows:

• The Ethernet LED glows a solid green when connected to a 100 Mbps Ethernet network.

• The Ethernet LED glows a solid orange when connected to a 10 Mbps Ethernet network.

• The Ethernet LED flashes when Ethernet packets are being transmitted or received.

Connecting to a Serial Device

The OnCell G3110/G3110-HSPA supports one RS-232 port that connects through a DB9 male connector on the

bottom panel.

The OnCell G3150/G3110-HSPA supports one RS-232 port that connects through a DB9 male connector on the

bottom panel, and one RS- - - - - 5-422/RS 485 4w/RS 485 2w that connects through a pin terminal block on the

bottom panel.

Connecting to the Ethernet Device

Connect one end of the Ethernet cable to the OnCell G3100's 10/100M Ethernet port and the other end of the

cable to the Ethernet device.

If the cable is properly connected, the OnCell G3100 will indicate a valid Ethernet connection as follows:

• The Ethernet LED glows a solid green when connected to a 100 Mbps Ethernet device.

• The Ethernet LED glows a solid orange when connected to a 10 Mbps Ethernet device.

• The Ethernet LED flashes when Ethernet packets are being transmitted or received.

Adjustable Low R s for - for Pull High/ esistor the RS 485 Port (

RS- ) 232/422/485 models

In some critical environments, you may need to add termination resistors to prevent the reflection of serial

signals. When using termination resistors, it is important to set the pull high/low resistors correctly so that the

electrical signal is not corrupted. Since a particular pull high/low resistor value cannot fit all environments, the

OnCell uses DIP switches to set the pull high/low resistor values for the serial port.

OnCell G3100 Series G etting Started

2-7

• To set the termination resistor to 150 KΩ

ΩΩ, make sure both of the assigned DIP switches are in the OFF

position. This is the default setting.

• To set the Ktermination resistor to 1 Ω

ΩΩ , make sure both of the assigned DIP switches are in the ON

position.

ATTENTION

not use the 1 KΩ setting on the OnCell when using the RS-232 inte . rface Doing so will degrade the RS-

232

signals

and shorten the maximum allowed communication distance.

SW 1 2 3

Pull High Pull Low Terminator

ON K 1 KΩ1 KΩ120 Ω

OFF – 150 KΩ150 KΩ

OnCell G3100 Series G etting Started

2-8

LED Indicators

The LED indicators on the front panel of the OnCell series are described in the following table.

LED Name LED Color LED Function

PWR G reen DC Power is active.

off Power is off, or power error condition exists.

Tx G . reen The serial port is transmitting data

O . ff No data is being transmitted or received through the serial port

Rx Amber The serial port is receiving data.

off No data is being received through the serial port.

REG Amber Registered with cellular provider (only for – JPS/JPN model)

off SIM slot not in used (only for – JPS/JPN model)

GSM Amber GSM is connected.

off GSM is disconnected.

GRPS Amber GPRS is connected

off GPRS is disconnected.

UMTS Amber UMTS is connected.

off UMTS is disconnected.

HSPA A mber HSPA is connected.

off HSPA is disconnected.

Ready Green

Steady on: Software Ready.

Blinking slowly (1 sec): The OnCell has been located by the OnCell Search

Utility.

off Power is off, or is booting up.

Fault Red Steady on: Booting up, or IP fault.

Blinking slowly (1 sec): Cannot get an IP address from the DHCP server

off . Power is off, or no errorthere is condition

Signal (3 LEDs) Green Signal Level

(at least 2 LEDs must illuminated for data transmission)

A TTENTION

GSM LED

OFF

: Cannot register with cellular providers using GSM mode, due to the wrong PIN code, or no

cellular

provider available. Signal LEDs will also be off.

: Registered with cellular provider. Signal LEDs will be on.

GPRS LED

OFF

: Ca

nnot register with cellular providers using GPRS mode, due to wrong PIN code (GSM/signal LEDs

off), no cellular provider available (GSM/signal LEDs off), wrong APN (GSM on/signal LEDs off), o

wrong username/password (GSM on/signal LEDs off).

: Registered with cellular provider using GPRS mode. GSM/Signal LEDs will be on.

UMTS/HSPA LED:

OFF:

Cannot register with cellular providers using UMTS/HSPA mode due to the wrong PIN code

(UMTS

or HSPA/signal LEDs off), no cellular provider available (UMTS or HSPA/signal LEDs off), wrong

APN (UMTS or HSPA on/signal LEDs off), or wrong username/password (UMTS or HSPA

on/signal LEDs off).

ON:

Registered with cellular provider using UMTS/HSPA mode. UMTS or HSPA/Signal LEDs will be

on.

OnCell G3100 Series G etting Started

2-9

Reset Button

Press the Rest button continuously for 5 sec to load factory defaults: Use a pointed object, such as a

straightened paper clip or toothpick, to press the reset button. This will cause the Ready LED to blink on and off.

The factory defaults will be loaded once the Ready LED stops blinking (default IP: 192.168.127.254).

OnCell G3100 Series Initial IP Address Configuration

3-2

Static and Dynamic IP Addresses

Determine whether your OnCell G3100 needs to use a static IP address or dynamic IP address (either DHCP or

B OOTP application).

• t If your OnCell G3100 is used in a static IP environment, you mus assign a specific IP address using

one of the tools described in this chapter.

• If your OnCell G3100 is used in a dynamic IP environment, the IP address will be assigned

automatically from over the network. In this case, set the IP configuration mode to DHCP or BOOTP.

ATTENTION

Consult your network administrator on how to reserve a

fixed IP address for your OnCell G3100 in the MAC-

mapping table when using a DHCP Server or BOOTP Server. For most applications, you should assign a fixed

IP ad

dress to your OnCell G3100.

Factory Default IP Address

The OnCell G3100 is configured with the following default private IP address:

192.168.127.254

Note that IP addresses that begin with are referred to as private IP addresses. Devices configured “ ” 192.168

with a private IP address are not directly accessible from a public network. For example, you would not be able

to ping a device with a private IP address from an outside Internet connection. If your application requires

sending data over a public network, such as the Internet, your OnCell G3100 will need a valid public IP address,

which can be leased from a local ISP.

Configuration Options

OnCell Search Utility

You may configure your OnCell G3100 y with the bundled OnCell Search Utilit for Windows. Please refer to

Chapter 15, Software Installation/Configuration, for details on how to install and use OnCell Search Utility.

Web Console

You may configure your OnCell G3100 using a standard web browser. Please refer to Chapter 6, Using the Web

Console, for details . on how to access and use the OnCell G3100 web console

ARP

You may use the ARP (Address Resolution Protocol) command to set up an IP address for your OnCell G3100.

The ARP command tells your computer to associate the OnCell G3100’s MAC address with an IP address.

Afterwards, use and its IP address will be reconfigured.Telnet to access the OnCell G3100

OnCell G3100 Series Initial IP Address Configuration

3-3

ATTENTION

In order to use

the ARP setup method, both your computer and the OnCell G3100

must be connected to the

same LAN.

Y n ou may use a Ethernet cable to connect the OnCell G3100 directly to your computer’

s Ethernet

card.

Before executing the ARP command, your OnCell G3100 must be configured with the factory

default IP

address (192.168.127.254) and your computer and the

OnCell G3100 must be on the same subnet. In

addition, note that ARP command must be issued within 3 minutes after the OnCell is

turned. After 3 minutes

have elapsed, the OnCell will no longer accept ARP commands.

To use ARP to configure the IP address, complete the following:

1. Obtain a valid IP address for your OnCell G3100 from your network administrator.

2. Obtain your OnCell G3100’s MAC address from the label on the bottom panel.

3. Execute the arp -s command from your computer’s MS DOS prompt as follows:-

arp -s <IP address> <MAC address>

F or example,

C:\ >arp - . - -s 192.168.200 100 00 90 E8- - - 04 00 11

4. Next, execute a special T elnet command by entering the following exactly:

telnet 192.168.200.100 6000

When you enter this command, a Connect failed message will appear, as shown below.

5. After the OnCell G3100 reboots, its IP address will be assigned to the new address and you can reconnect

using Telnet to verify that the update was successful.

Telnet Console

Depending on how your computer and network are configured, you may find it convenient to use network

access to set up your s IP address. This can be done using Telnet.OnCell G3100’

ATTENTION

Figures in this section were taken from

the OnCell G3100’s Telnet console.

OnCell G3100 Series Initial IP Address Configuration

3-4

1. From the Windows desktop, select Start  Run, and then type the following content in the Run window:

telnet 192.168.127.254

If your IP address is different from the default . setting, use your IP address instead. Click OK

2. The console terminal type selection is displayed as shown. Enter 1 for ansi/vt100, and then press ENTER

to continue.

3. The following page will only appear if the OnCell G3100 is password protected. Enter the console password

if you are prompted to do so, and then press ENTER.

4. Press N or use rrow keys the a to select Network, and then press ENTER.

OnCell G3100 Series Initial IP Address Configuration

3-5

5. Press B or use rrow keys the a to select Basic, and then press ENTER.

6. U kse the arrow eys to move the cursor to IP address. Use the DELETE, BACKSPACE SPACE , or keys to

erase the current IP address, type in the new IP address and press and then ENTER. Note that if you are

using a dynamic IP configuration (BOOTP, DHCP, etc.), you will need to go to the IP configuration field

and press ENTER to select the appropriate configuration.

7. Press the ESC twice to return to previous page. Press Y to confirm.

8. Press the ESC to return to previous page.

OnCell G3100 Series Initial IP Address Configuration

3-7

Serial Console

The OnCell G3100 supports configuration through the serial console, which is the same as the Telnet console

but accessed through the RS- 232 console port rather than over the network. Once you have entered the serial

console, the configuration options and instructions are the same as if you were using the Telnet console.

The following instructions and screenshots show how to enter the serial console using PComm Terminal

Emulator, which is . Yavailable free of charge as part of the PComm Lite suite ou may use a different terminal

emulator utility, although your actual screens and procedures may vary slightly from the following instructions.

1. Turn off the power to the OnCell G3100. Use a serial cable to connect the OnCell G3100’s serial console port

to - your computer’s RS 232 serial port.

2. From the Windows desktop select Start



 All Programs 



 PComm Lite 



 Terminal Emulator.

3. The PComm Terminal Emulator window should appear. From the Port Manager menu, select Open, or

simply click the Open icon as shown below:

4. The Property window opens automatically. Select the then select Communication Parameter tab, and

the appropriate COM port for the connection (COM4 in this example). Configure the parameters for 115200,

8 N 1, , 1 (15200 for B raud ate, 8 for Data Bits, None for Parity, and 1 for Stop Bits).

5. From the Property window’s Terminal page, select ANSI or VT100 for Terminal Type and then click OK.

6. If you are using the OnCell G3100, you may power it up at this point and hold down the “grave accent key”

(`) while powering it up, as shown below. Note that the grave accent key (sometimes called “backwards

apostrophe”) is — NOT the apostrophe key it is the key usually found next to the number 1 key.

Produkt Specifikationer

Mærke:	Moxa
Kategori:	Ikke kategoriseret
Model:	OnCell G3110-HSPA

Har du brug for hjælp?

Hvis du har brug for hjælp til Moxa OnCell G3110-HSPA stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Moxa Manualer

Moxa OnCell 5104-HSDPA Manual

11 Januar 2025

Moxa OnCell G3150 Manual

23 August 2024

Moxa ICF-1150I-M-ST Manual

23 August 2024

Moxa M-3411 Manual

23 August 2024

Moxa M-1600 Manual

23 August 2024

Moxa TCC-82-RP Manual

23 August 2024

Moxa MGate MB3270-T Manual

23 August 2024

Moxa UPort 1410 Manual

23 August 2024

Moxa M-1450 Manual

23 August 2024

Moxa TCF-142-S-ST-T Manual

23 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterpik WP-490 Manual

10 April 2025

Daikin EAVX16S18DA9WG Manual

10 April 2025

Daikin RXYLQ40T7Y1B Manual

10 April 2025

Daikin RXYLQ42T7Y1B Manual

10 April 2025

Daikin ETVZ16S23EA6V7 Manual

10 April 2025

Daikin FXMA200AXVMB Manual

10 April 2025

Daikin FXZQ15A2VEB Manual

10 April 2025

Daikin ETVZ16S18EA9W Manual

9 April 2025

Daikin DSR1 Manual

9 April 2025

Simplified MFG SP18CAT120 Manual

9 April 2025