Nikon Nikkor Z 24-70mm f/2.8S Manual (3 Sider)

En

User’s Manual

Fr

Manuel d’utilisation

Es

Manual del usuario

NIKKOR Z 24-70mm f/2.8 S

Printed in Japan

SB9A01(30)

7MMA2030-01

En

User’s Manual

Before using this product, please read these instructions carefully. You will also need to

consult the camera manual.

• This lens is intended exclusively for use with mirrorless cameras featuring a Nikon Z mount.

For Y

For Your Safety

our Safety

For Your Safety

To prevent damage to property or injury to yourself or to others, read “For Your Safety”

in its entirety before using this product.

Keep these safety instructions where all those who use this product will read them.

A WARNING: Failure to observe the precautions marked with this icon could

result in death or severe injury.

A CAUTION: Failure to observe the precautions marked with this icon could

result in injury or property damage.

A

WARNING

•

Do not disassemble or modify this product.

Do not touch internal parts that become exposed as the result of a fall or

other accident.

Failure to observe these precautions could result in electric shock or other injury.

•

Should you notice any abnormalities such as the product producing smoke

Should you notice any abnormalities such as the product producing smoke, heat, or

, heat, or

Should you notice any abnormalities such as the product producing smoke, heat, or

unusual odors, immediately disconnect the camera power sourc

unusual odors, immediately disconnect the camera power source.

e.

unusual odors, immediately disconnect the camera power source.

Continued operation could result in ﬁ re, burns or other injury.

•

Keep dry.

Do not handle with wet hands.

Failure to observe these precautions could result in ﬁ re or electric shock .

•

Do not use this product in the presence of ﬂ

ammable dust or gas such as

Do not use this product in the presence of ﬂ ammable dust or gas such as

propane, gasoline or aerosols.

Failure to observe this precaution could result in explosion or ﬁ re.

•

Do not directly view the sun or other bright light source through the lens

or camera.

Failure to observe this precaution could result in visual impairment.

•

Keep this product out of reach of children.

Failure to observe this precaution could result in injury or product malfunction. In

addition, note that small parts constitute a choking hazard. Should a child swallow any

part of this product, seek immediate medical attention.

•

Do not handle with bare hands in locations exposed to extremely high or

low temperatures.

Failure to observe this precaution could result in burns or frostbite.

A

CAUTION

•

Do not leave the lens pointed at the sun or other strong light sourc

Do not leave the lens pointed at the sun or other strong light sources.

es.

Do not leave the lens pointed at the sun or other strong light sources.

Light focused by the lens is a source of ﬁ re and damage to the product’s internal parts.

•

Do not leave the product where it will be exposed to extremely high

temperatures, for an e

temperatures, for an extended period such as in an enclosed automobile

xtended period such as in an enclosed automobile

temperatures, for an extended period such as in an enclosed automobile

or in direct sunlight.

Failure to observe this precaution could result in ﬁ re or product malfunction.

•

Do not transport cameras or lenses with tripods or similar accessories

attached.

Failure to observe this precaution could result in injury or product malfunction.

Notices for Customers in the U

Notices for Customers in the U.S.A.

.S.A.

Notices for Customers in the U.S.A.

This device complies with part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

Federal Communications C

Federal Communications Commission (FCC) Radio Frequency Interference

ommission (FCC) Radio Frequency Interference

Federal Communications Commission (FCC) Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-

able protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a particular instal-

lation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment oﬀ and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit diﬀ erent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

CAUTIONS

Modi cations

The FCC requires the user to be notiﬁ ed that any changes or modiﬁ cations made to

this device that are not expressly approved by Nikon Corporation may void the user’s

authority to operate the equipment.

Nikon Inc., 1300 Walt Whitman Road,

Melville, New York 11747-3064, U.S.A.

Tel.: 631-547-4200

Notice for Customers in Canada

CAN ICES-3 B / NMB-3 B

Using the Lens

Parts of the Lens: Names and Functions

Refer to the diagram on the left edge of this sheet.

qLens hood mounting

mark Use when attaching the lens hood. See D

wFocus ring

Use for manual focus. When focusing using

autofocus, you can adjust focus manually by

rotating the ring while the shutter-release but-

ton is pressed halfway; after focusing, press

the shutter-release button the rest of the way

down to shoot.

—

eZoom ring Rotate to zoom in or out. —

rFocal length scale Determine the approximate focal length when

zooming the lens in or out. —

tFocal length mark

yLens info panel View focus distance, depth of ﬁ eld, and other

information.

See B,

C

uControl ring

Rotate to adjust a setting such as or Aperture

Exposure compensation assigned using the cam-

era. For more information, see the description

of Custom control assignment in the camera

manual.

—

iLens mounting mark Use when mounting the lens on the camera. See A

oRubber lens-mount

gasket — —

!0 CPU contacts Used to transfer data to and from the camera. —

!1 L-F n button

Press to perform a function assigned using the

camera. For more information, see the descrip-

tion of Custom control assignment in the camera

manual.

—

!2 Display button Save settings or choose the information shown

in the lens info panel.

See B,

C

!3 Focus-mode switch

Choose A for autofocus, for manual focus. M

Note that regardless of the setting chosen, fo-

cus must be adjusted manually when manual

focus mode is selected using camera controls.

—

!4 Lens hood lock mark Use when attaching the lens hood.

See D

!5 Lens hood

Lens hoods block stray light that would other-

wise cause ﬂ are or ghosting. They also serve to

protect the lens.

●

●●

!6 Lens hood alignment

mark Use when attaching the lens hood.

!7 Hood release Use when removing the lens hood.

!8 Front lens cap — —

!9 Rear lens cap — —

A

Attachment and Removal

Attaching the Lens

z

Turn the camera o , remove the body cap, and detach the rear lens cap.

x Position the lens on the camera body, keeping the mounting mark

on the lens aligned with the mounting mark on the camera body,

and then rotate the lens counterclockwise until it clicks into place.

Removing the Lens

z Turn the camera o .

x

Press and hold the lens release button while turning the lens clockwise.

B

The Lens Info Panel

The lens Info panel lights when the lens is at-

tached to a camera and the camera is on.

Press the display button to cycle the display as shown:

Display button

Depth of  eld

Aperture* Focal length

Focus distance

* Aperture is displayed only when the camera is

in mode A or . The display for other modes is M

shown in the illustration.

• The focus mode ( or AF MF) is brieﬂ y displayed when chosen using the focus-

mode switch.

• The panel turns oﬀ automatically when the camera standby timer expires or if

no lens operations are performed for about 10 seconds. Press the display button

to reactivate the display.

A The Lens Info Panel

The focus distance, depth of  eld, and other information displayed in the lens Info panel are approxima-

tions only.

C

Panel

Panel Options

Options

Panel Options

Follow the steps below to choose the units for focus distance from meters (m) or

feet ( ) or adjust the brightness of the lens Info panel.ft

z Press and hold the display button to view settings.

• Unit or brightness selection options will be displayed. The currently select-

ed item will ﬂ ash.

• Press the display button to toggle between displays.

Units Brightness

x Choose a setting using the lens control ring.

Units

-Rotate the control ring to choose from me-

ters ( ) or feet ( ).m ft

Brightness

-Rotate the control ring in the “+” (brighter)

or “−” (darker) direction.

-Choose from 6 levels of brightness.

-To turn the lens info panel oﬀ , rotate the

ring in the “−” direction until the icon

changes to .

• Press the display button to save changes and toggle the display.

• If no operations are performed using lens controls for about 5 seconds,

panel options will clear from the display and changes will be canceled.

c Press and hold the display button to return to the lens information dis-

play.

• Choosing for brightness turns the lens info panel oﬀ . To turn the display

on again, press and hold the display button.

D

Attaching and Removing the Lens Hood

Attaching the Lens Hood

Align the lens hood mounting mark with the lens hood alignment mark (

q) and

then rotate the hood (

w) until the mounting mark is aligned with the lens hood

lock mark (

e).

Lens hood lock mark

Lens hood alignment mark

Lens hood mounting mark

When attaching or removing the hood, hold it near the lens hood alignment mark (●)

and avoid gripping the front of the hood too tightly. The hood can be reversed and

mounted on the lens when not in use.

Removing the Lens Hood

Keeping the hood release pressed (q), rotate the hood in the direction shown

(w

) and remove it from the lens (e).

Hood release

The same procedure can be used when the hood is reversed.

When the Lens Is Attached

The focus position may change if you turn the camera oﬀ and then on again after

focusing. Refocus before shooting. If you have focused on a pre-selected location while

waiting for your subject to appear, we recommend that you do not turn the camera oﬀ

until the picture is taken.

Precautions for Use

• Do not pick up or hold the lens or camera using only the lens hood.

• Keep the CPU contacts clean.

• Should the rubber lens-mount gasket be damaged, cease use immediately and take

the lens to a Nikon-authorized service center for repair.

• Replace the front and rear lens caps when the lens is not in use.

• To protect the interior of the lens, store it out of direct sunlight.

• Do not leave the lens in humid locations or in locations in which it may be exposed to

moisture. Rusting of the internal mechanism can cause irreparable damage.

• Do not leave the lens next to open ﬂ ames or in other extremely hot locations. Ex-

treme heat could damage or warp exterior parts made from reinforced plastic.

• Rapid changes in temperature may cause damaging condensation inside and outside

the lens. Before taking the lens from a warm to a cold environment or vice versa, place

it in a bag or plastic case to slow the change in temperature.

• We recommend that you place the lens in its case to protect it from scratches during

transport.

Lens Care

• Removing dust is normally suﬃ cient to clean the glass surfaces of the lens.

• The ﬂ uorine- coated front and rear lens elements can be cleaned as described below.

-Smudges, ﬁ ngerprints, and other oily stains can be removed using a soft, clean cot-

ton cloth or lens cleaning tissue; clean from the center outwards using a circular

motion.

-To remove stubborn stains, wipe gently using a soft cloth lightly dampened with a

small amount of distilled water, ethanol, or lens cleaner.

-Any drop-shaped marks left from this process on the water- and oil-repellent sur-

face can subsequently be removed with a dry cloth.

• Never use organic solvents such as paint thinner or benzene to clean the lens.

• Neutral Color (NC) ﬁ lters (available separately) and the like can be used to protect the

front lens element.

• If the lens will not be used for an extended period, store it in a cool, dry location to

prevent mold and rust. Do not store in direct sunlight or with naphtha or camphor

moth balls.

Accessories

Supplied Accessories

• LC-82B 82 mm snap -on Front Lens Cap

• LF-N1 Rear Lens Cap

• HB-87 Bayonet Hood

• CL-C2 Lens Case

D Using the Lens Case

• The case is intended to protect the lens from scratches, not from falls or other physical shocks.

• The case is not water resistant.

• The material used in the case may f ade, bleed, stretch, shrink, or change color when rubbed or wet.

• Remove dust with a soft brush.

• Water and stains can be removed from the surface with a soft, dry clot h. Do not use alcohol, benzene, thinner,

or other volatile chemicals.

• D o not store in locations exposed to direct sunlight or high temperatures or humidity.

• D o not use the case to clean the monitor or lens elements.

• B e careful that the lens does not fall from the case during transport.

Material: Polyester

Compatible Acc

Compatible Accessories

essories

Compatible Accessories

82 mm screw-on ﬁ lters

D Filt ers

Use only one  lter at a time. Remove the lens hood before attaching  lters or rotating circular polarizing  lters.

Speci

cations

Speci cations

Mount

Mount Nikon Z mount

Focal length

Focal length 24 – 70 mm

Maximum aperture

f/2.8

Lens construction

Lens construction 17 elements in 15 groups (including 2 ED elements, 4 aspherical elements,

elements with Nano Crystal and ARNEO coats, and  uorine- coated front and rear lens

elements)

Angle of view

Angle of view • FX format: 84°–34°20c

• DX format: 61°–22°50c

Focal length scale

Focal length scale Graduated in millimeters (24, 28, 35, 50, 70)

Focusing system

Focusing system Internal focusing system

Minimum focus

distance

distance 0.38 m (1.25 ft) from focal plane at all zoom positions

Maximum repro-

duction ratio

duction ratio Approx. 0.22×

Diaphragm

blades

blades 9 )(rounded diaphragm opening

Aperture range

Aperture range f/2.8 – 22

Filter-att achment

size

size 82 mm (P = 0.75 mm)

Dimensions

Dimensions Approx. 89 mm/3.6 in. maximum diameter × 126 mm/5 in.

(distance from camera lens mount  ange)

Weight

Weight Approx. 805 g (1 lb 12.4 oz)

Nikon reserves the right to change the appearance, speciﬁ cations, and performance of this

product at any time and without prior notice.

Nikon Nikkor Z 24-70mm f/2.8S Manual

Produkt Specifikationer

Har du brug for hjælp?

Lens Nikon Manualer

Lens Manualer

Nyeste Lens Manualer