Oliveri DZ122 Manual
Læs nedenfor 📖 manual på dansk for Oliveri DZ122 (4 sider) i kategorien Vask. Denne guide var nyttig for 14 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/4
INSTALLER - PLEASE READ & FOLLOW
THESE INSTALLATION INSTRUCTIONS
Please retain for consumer as care instructions are included
EQUIPMENT REQUIRED for installing your top mount sink: Sonetto
MATERIALS FOR CUTTING COUNTER/BENCHTOP:
•Template for your particular model sink and mounting method (may be inside or printed
on carton depending on model). If not available, the sink itself may be used.
•Marker such as a pencil or similar for tracing the template onto the counter/benchtop
•Tape measure
•Drill with 12mm / ½” diameter bit or larger (wood counter/benchtop)
•Cutting Device (such as a jigsaw) with suitable blade for counter/benchtop material
•Suitable protection such as gloves and goggles to be used while drilling or cutting
MATERIALS FOR FITTING THE TOP MOUNT SINK:
•Sonetto sink dered) (with correct tap holes as or - includes mounting clips, sealing
gasket, model). basket wastes and other accessories (depending on
•These Installation Instructions
•Level sto check counter/benchtop & sink i installed level
•Phillips head screwdriver mounting clips)(#2 to tighten
•Flat head screwdriver (large - to tighten basket wastes)
•Suitable sealant (neutral-cure silicone sealant or equivalent)
•Masking material ss sealantto protect counter/benchtop and sink from exce
•Additional Mounting Hardware clamps cluded withif fitting into thinner material. The in
the sink require a minimum counter/benchtop thickness of 25mm / 1”.
CHECK MODEL & TAP HOLES
The model number on the sink
packaging must match the model
of sink the customer ordered.
Check the number and position of
tap holes is correct.
Do not install if incorrect.
CHECK THE CONDITION
Inspect the sink for any visible
defects. Do not install the sink if
defects are found. Contact your
sink retailer / point of purchase.
AVOID CUTS
The perimeter and punch-outs on
the sink may contain sharp edges.
Handle the sink carefully to avoid
personal injury.
AVOID SCRATCHES
Polished stainless steel can be
scratched if proper care is not
taken during installation.
Topmount sinks may also be know as “drop in” or “inset” sinks. n
Sink models w
ith prefix MO, PE, UF, DU, LR, EF, NP, MR, SI & RR.
These sinks will fi
t into standard 600mm bench tops.
Templates su
pplied are to assist in achieving th for top mounting the sink.e correct shape hole
Careful use of the templ
ate is required to achieve the correc cutout shape. the template not available, the cut out t If is
shap carefullye may be created by
inverting the sink onto the counter/benchtop d tracing ar an ound the perimeter. Cut
the hole 10mm inside the traced line.
Many Sonetto sinks have waste outlets positi he sink is correctlyoned to the rear of the bowls. Ensure t positioned when
fitting.
Unequal bowl depth:
Sinks that combine different sized bowls may also have unequal bow Waste plumbing l depth. will need to
accommodate this variance. MO, PE, NP, SI & RR sinks have a height adaptor included with the sink where needed.
Models UF03D & UF
04D have a 60mm height difference in waste connections for the main and smaller bowl. Waste
plumbing will need to accommodate this va
riance.
Models UF05D & UF
06D have a 35mm height difference in waste connections for the main and smaller bowl. Waste
plumbing will need to accommodate this va
riance.
EF emodels have a 35mm h
ight difference in waste connecti for the main and smaller bowl. Waste plumbi ons ng will
need to accommodate this
variance.
MANHATTAN & DAL
LAS (MH or DA)
THESE SINKS WILL NOT FIT IN
A STANDARD 600MM COUNTER/BENCH TOP.
Measure carefully to
ensure sufficient room exists (including allowance for a splashback if required). The cutout
shape may be created by carefully
inverting the sink onto the counter/benchtop d tracing ar an ound the perimeter. Cut
the hole 10mm inside the traced line.
FOR “TOP MOUNT’ OR “DROP IN” SINKS
NORTH AMERICA DISTRIBUTORS
Andrew Sheret LTD
7434 Edmonds St, Wholesale
Counter, Burnaby, BC V3N 1A8,
Canada
Phone: 604-521-0788
Mega Western Sales LLC
6861 Walker St, La Palma,
CA 90623, USA
Phone: 310-323-7900 Any advice, recommendation, information, assistance or service provided by Tasman Sinkware in
relation to goods manufactured by it or their use and installation, is given in good faith and is believed by
Tasman Sinkware to be appropriate and reliable. However, any advice, recommendation, information,
assistance or service is provided by Tasman Sinkware without responsibility or liability.
SPECIAL INSTRUCTIONS FOR PARTICULAR TOP MOUNT SINK MODELS
CAUTION
Leave protective tape on the sink when inverting over a benchtop and tracing its shape.
The polished stainless steel will scratch if the sink slides across a hard surface.
© Tasman Sinkware 2006
AU Top Mount Installation Instructions
TF 08d.doc
Tasman Sinkware
is a division of
Fletcher Building
AUSTRALIA
HeadOff e&ic
Manufacturing Plant
Tasman Sinkware Pty Ltd
Regency Park SA
Phone: +61 8 8348 6444
Fax: +61 8 8348 6495
Email:
sinkware@tasbuildpro.com.au
www. .comsonettosinks
Tasman Sinkware
is a division of
Fletcher Building
Produkt Specifikationer
| Mærke: | Oliveri |
| Kategori: | Vask |
| Model: | DZ122 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Oliveri DZ122 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Vask Oliveri Manualer
1 September 2024
1 September 2024
1 September 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
Vask Manualer
- Vask Concept
- Vask Teka
- Vask Hotpoint Ariston
- Vask Blaupunkt
- Vask Smeg
- Vask Kernau
- Vask Caple
- Vask Franke
- Vask Nodor
- Vask Saro
- Vask CDA
- Vask Artusi
- Vask BLANCO
- Vask Foster
- Vask Rangemaster
- Vask Elkay
- Vask Schock
- Vask Roca
- Vask Advance Tabco
- Vask Eagle Group
- Vask Sani-Lav
- Vask Laveo
- Vask Deante
- Vask Tot Mate
- Vask Kuchinox
- Vask Shaws
Nyeste Vask Manualer
8 December 2024
8 December 2024
8 December 2024
8 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024