Olympus Camedia E-20N Manual

Olympus Kamera Camedia E-20N

Læs nedenfor 📖 manual på dansk for Olympus Camedia E-20N (2 sider) i kategorien Kamera. Denne guide var nyttig for 14 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

PProgram mode Camera selects the correct aperture and shutter

speed automatically.

AAperture priority mode Camera sets the correct shutter speed for the

aperture that you select by moving the sub dial

left or right.

SShutter priority mode Camera sets the correct aperture for the shutter

speed that you select by moving the sub dial left or

right.

MManual mode You select the aperture with the main dial and the

shutter speed with the sub dial.

3 Adjust the viewfinder for your eyes. If you wear eyeglasses, you may need to

sharpen the viewfinder display.

• If the AF target mark in the center of the viewfinder is not sharp, turn the diopter adjustment

ring around the viewfinder left or right until the AF target mark is sharp.

4 Select the memory card.

• If only one memory card is installed in the camera, the card is selected automatically for

storing pictures that you take. If both cards are installed, the control panel display will tell

you which card is currently selected for storing pictures.

SmartMedia memory card selected.

CompactFlash/Microdrive memory card selected.

• If you want to switch the selection, press and hold the SM/CF memory card button (K), then

turn the main dial until it clicks. In the control panel you should see or displayed.

Go!

1 Make sure that the lens cover has been removed.

2 Take a picture.

• Point the camera at the subject that you want to take a picture, and look through the

viewfinder to compose the picture.

• Turn the zoom ring to enlarge or reduce the size of the subject in the viewfinder.

• With the picture composed in the viewfinder, use the flat of your index finger to half-press

the shutter button ( ) and wait for the AF correct mark light in the lower left corner of thec

viewfinder to light. When you see the AF correct mark light, the picture is correctly focused

and exposure is calculated.

• Fully-press the shutter button to take the picture. After the shutter releases, the monitor on

the back of the camera briefly displays the image of the picture you have just taken and

then goes off.

• If you see the mark blinking in the viewfinder, this means that you should use the flash.

• On the left side of the camera, near the top, press the flash button to raise the built-in flash

unit. The flash will fire automatically to ensure correct exposure of the picture.

3 Repeat from Step 2 to take a few more pictures.

4 View the pictures that you have just taken.

• Set the mode dial to playback . The monitor on the back of the camera switches on and

you will see the the last picture taken.

• On the arrow pad, press or to display the other shots one by one.

• If you want to display several images at once so you can quickly locate a picture, turn the

main dial to the left. Every time you move the dial left you will see 4, 9, then 16 frames in

the monitor. This is called the index display where each set of 4, 9, or 16 frames are

displayed as an index.

• Press or to display the next index. On the arrow pad, press or to move the

green highlight within the displayed index to select the picture that you want to display.

• If you want to enlarge the display so you can check the focus of the picture, turn the main

dial clockwise to enlarge the display in steps. As you enlarge the display, the view becomes

smaller. Press on the arrow pad to scroll around the enlarged image. Turn the

main dial counterclockwise until the original display is restored.

5 Delete a picture.

• With the frame that you want to delete displayed in the monitor, press the erase button

on the back of the camera near the bottom edge. If you are using the index display, use

on the arrow pad to select the picture that you want to erase, and press the

erase button.

• To switch off playback, set the mode dial to P A S, , , or M.

]

[

Important Parts and Names

Digital Camera

Quick Start Guide

Follow these simple instructions to start using your camera in minutes. Read the other

instructions provided with the camera for detailed descriptions of all the exciting features that the

Olympus E-20 packs into its compact design.

Ready!

You have to complete several important tasks before you can use the camera.

1 Attach the strap.

• Thread the ends of the strap through the eyelets on both sides of the camera. Slide the

ends of the straps through the sleeve and frame, and then pull them tight. Slide the sleeve

up the eyelets on both sides.

2 Load the lithium battery packs provided with the camera.

• On the bottom of the camera, turn the battery compartment knob to the open position ,

open the compartment, and then remove the battery case.

• With the +/ polarities aligned correctly, insert the battery packs into the battery, taking care−

not to reverse the +/ polarity.−

• Load the case in the camera. Push down lightly on the compartment case, and then move

the battery compartment knob to the close position .

Note:

Your camera can also use the following types of batteries: AA (R6) Ni-MH ( 4), AA (R6) Ni-Cd×

(×4), B-12LPB/B-10LPB (included in the optional B-32LPS/B-30LPS lithium polymer battery

sets), and AA (R6) Alkaline (×4).

Caution:

Never use AA (R6) zinc-carbon (manganese) or AA (R6) lithium batteries with this camera.

These batteries could overheat and seriously damage the camera.

3 Insert the memory cards.

• The camera can hold one SmartMedia® and one CompactFlash®/Microdrive* (CF Type II

standard) memory card. Either card can be installed alone or both can be installed together,

but at least one memory card of either type must be installed in the camera before you take

pictures.

* Use of the Microdrive card requires the B-32LPS/B-30LPS lithium polymer battery set due

to the power requirements of the Microdrive.

• Hold the camera with the lens facing away from you. Lift up the card cover lock ( ) up whileJ

pressing the round release button under it to open the card cover.

• To install a SmartMedia card, hold it with its notched corner down, and insert it into the

thinner slot closest to the back of the camera. Gently push the card completely into the slot.

(Insert the SmartMedia card until you can see about 2 mm of the card above the edge of

the slot.)

• To remove the SmartMedia card, push it in gently to release and then pull it out of the slot.

• To install the CompactFlash/Microdrive card, hold the card so that the arrow on the card can

be seen and points into the slot, then insert it straight into the wider slot. Gently push in the

card until it stops.

• To remove the CompactFlash/Microdrive card, gently press the eject button below the slot.

Caution:

Careful! If you press the eject button too hard, the CompactFlash/Microdrive card could pop

out of the slot.

4 Switch the camera on.

• The power switch (O P) is underneath the mode dial ( ). Move the power switch toward you

to the ON position. The control panel on top of the camera comes on.

• The batttery check mark in the control panel on top of the camera tells you that the batteries

are fully charged. When this mark begins to blink, the batteries are low and you should

replace them as soon as possible. If this mark goes off, the batteries are dead and the

camera cannot be used unless you replace the batteries.

• The large number to the right of the battery check tells you the approximate capacity of the

selected card. As each picture is taken, this number will decrease until it reaches 0 and the

card is full.

• To switch the camera off, move the power switch forward to the OFF position.

5 Set the date and time.

• On the top right corner of the camera, set the mode dial to the setup/connection mode mark

• Press the menu button ). The menu appears in the monitor.(a

• On the arrow pad, press once to move the green highlight to the time setting mark .

• With the time setting mark highlighted, press once to move the green highlight to the

mark. Below the date, the date format, Y-M-D for example, where Y, M, D stand for the Year,

Month, Day, is displayed.

• Press or to select the date format (Y-M-D, M-D-Y, etc.), and then press . Two

pointers appear above and below the first setting.

• Now you can set the date. On the arrow pad, press or to increase or decrease the 2-

digit number. With the desired number displayed (12 for example) press to move the

pointers to the next position. (To return to the previous position, press .) Repeat this until

you finish setting the date and time. Note that the 24-hour system is used for the hours.

• When you finish the settings, press the button. The green highlight returns to the time

setting mark . Press the button again to close the menu.

Get Set!

1 If the lens cover is on the lens, remove it.

2 Select the shooting mode.

• Move the mode dial to the (Program mode) setting. With the mode dial set to , theP P

camera automatically selects the correct aperture and shutter speed for the best exposure.

This is the best setting if you are just getting started.

Four shooting modes are available. For details, refer to the Reference Manual.

1Metering mode button

2Drive button

3Remote cable jack

4Built-in flash

5Flash button

6Manual focus ring

7Zoom ring

8Exposure compensation button

9Macro button

0Flash synchro socket

AFocus mode switch

BStrap eyelet

CDC IN jack cap

DMonitor

EEyepiece shutter lever

FDiopter adjustment ring

GViewfinder

HMain dial

ICard cover

JCard cover lock

KSM/CF memory card button

LCard access lamp

MLight button

NAE lock button

OPower switch

PMode dial

QWhite balance mode button

RSub dial

SControl panel

TRecord mode button

UFlash mode button

VHot shoe

WVideo OUT jack

XUSB connector

YMonitor lock/release button

ZINFO button

[Protect button

\Erase button

]Arrow pad

^OK button

aMenu button

bMonitor button

cShutter button

dRemote control receiver/self-timer lamp

eStrap eyelet

fBattery compartment

gTripod socket

hLens

iQuick reference (one touch) white

balance button

jAF port

kSpeaker

Produkt Specifikationer

Mærke:	Olympus
Kategori:	Kamera
Model:	Camedia E-20N

Har du brug for hjælp?

Hvis du har brug for hjælp til Olympus Camedia E-20N stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Kamera Olympus Manualer

Olympus Stylus 770 SW Manual

19 August 2024

Olympus SZ-31MR Traveller Manual

10 August 2024

Olympus µ TOUGH-8000 Manual

7 August 2024

Olympus C-200 Manual

6 August 2024

Olympus SuperZoom 120 Manual

5 August 2024

Olympus C-765 Manual

4 August 2024

Olympus Smart VR-370 Manual

3 August 2024

Olympus Camedia D-425 Manual

30 Juli 2024

Olympus AZ-220 Wide Zoom Manual

29 Juli 2024

Olympus µ-550WP Manual

29 Juli 2024

Kamera Manualer

Nyeste Kamera Manualer

Trust Powerc@m 820 Manual

15 Oktober 2024

AVerMedia Live Streamer CAP 4K BU113 Manual

15 Oktober 2024

Panasonic Lumix DMC-LC5 Manual

15 Oktober 2024

Polaroid 600 Series Manual

8 Oktober 2024

Kodak EasyShare C1530 Manual

4 Oktober 2024

Lorex U222AA Manual

4 Oktober 2024

Leica R3 Manual

4 Oktober 2024

Canon EOS R10 Manual

3 Oktober 2024

Easypix V515 Duo Manual

2 Oktober 2024

Samsung DV1506F Manual

1 Oktober 2024