Optex AX-200TFR Manual

Optex Detektor AX-200TFR

Læs nedenfor 📖 manual på dansk for Optex AX-200TFR (12 sider) i kategorien Detektor. Denne guide var nyttig for 25 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/12
-1-
Warning
Caution
Warning
Caution
N219
1
2
3
4
5
6
INSTALLATION INSTRUCTIONS
No.59-1552-1 090403
BATTERY OPERATED
PHOTOELECTRIC DETECTOR
AX-100TFR/AX-200 TFR
BATTERY OPERATED
PHOTOELECTRIC DETECTOR
AX-100TFR/AX-200 TFR
•AX-100TFR : Detection range: 30 m (100 ft.)
•AX-200TFR : Detection range: 60 m (200 ft.)
CONTENTS
Battery-operated detector
Batteries are not included.
Use four LSH20 (3.6 V, 13 Ah) batteries manufactured by SAFT.
Battery life: AX-100TFR Approximately five years
AX-200TFR Approximately three years (transmitter)
Approximately five years (receiver)
Back box for wireless transmitters
Back box can conceal two wireless transmitters and batteries.
N.C./N.O. selection switch
Both N.C. and N.O. input wireless transmitters can be used.
Battery saving function for wireless transmitter
Turning ON the battery saving timer switch reduces the battery
consumption of the wireless transmitter.
Intermittent output function
Turning ON the intermittent output function, alarm signals are sent
periodically to avoid missed alarms while the beam is broken.
4 channel beam frequency selector
Crosstalk is eliminated with 4, channel selectable, beam
frequencies. Used when stacking beams or for long range
applications.
International protection
IP55
LED indicator for an easy alignment
It flickers on/off to help with easy alignment located on the receiver.
D.Q. circuit (environmental disqualification)
The environmental compensation circuit is designed to eliminate
false alarms caused by snow, fog, heavy rain, ice and misalignment.
Tamper
Form C output activates when either cover or back box or chassis
is removed.
Beam interruption adjustment function
This function allows you to select the suitable beam interruption
time for any environment.
FEATURES
Failure to follow the instructions provided with
this indication and improper handling may cause
death or serious injury.
Failure to follow the instructions provided with
this indication and improper handling may cause
injury and/or property damage.
Do not use the product for purposes other than the detection
of moving objects such as people and vehicles.
Do not use the product to activate a shutter, etc., which may
cause an accident.
Do not touch the unit base or power terminals of the
product with a wet hand (do not touch when the product
is wet with rain, etc.). It may cause electric shock.
Never attempt to disassemble or repair the product. It may
cause fire or damage to the devices.
Do not use batteries other than those specified.
Specified batteries:
Four LSH20 batteries manufactured by SAFT
Do not use batteries that have different levels of power
remaining (i.e., new and used batteries).
Not observing the above may result in an explosion, leakage
of electrolyte, emission of toxic gases or other outcomes that
may be harmful to people and property.
[Handling of Batteries]
Fire, explosion and severe burn hazard. Do not recharge,
short circuit, crush, disassemble, heat above 100°C (212°F),
incinerate, or expose contents to water.
Do not solder directly to the cell.
Do not pour water over the product with a bucket, hose, etc.
The water may enter, which may cause damage to the
devices.
Clean and check the product periodically for safe use. If any
problem is found, do not attempt to use the product as it is
and have the product repaired by a professional engineer or
electrician.
Read this instruction manual carefully prior to installation.
After reading, store this manual carefully in an easily accessible
place for reference.
This manual uses the following warning indications for correct use
of the product, harm to you or other people and damage to your
assets, which are described below. Be sure to understand the
description before reading the rest of this manual.
This symbol indicates prohibition. The specific prohibited
action is provided in and/or around the figure.
This symbol requires an action or gives an instruction.
INTRODUCTION
1-1 BEFORE YOUR OPERATION 1
1-2 PRECAUTIONS 2
1-3 PARTS IDENTIFICATION 2
PREPARATIONS
2-1 ORDERING DETECTOR BATTERIES 2
2-2
CHECKING THE WIRELESS TRANSMITTER SIZE
2
INSTALLATION
3-1 WALL MOUNTING 3
3-2 POLE MOUNTING 4
3-3 MOUNTING IN THE BEAM TOWER 5
3-4 WIRING 7
SETTING
4-1 FUNCTION 8
4-2
4 CHANNEL BEAM FREQUENCY SELECTOR
8
4-3 OPTICAL ALIGNMENT 9
4-4 BEAM INTERRUPTION ADJUSTMENT 9
4-5 ADJUSTING OUTPUT 10
OPERATION CHECK
5-1 LED INDICATION 11
5-2 OPERATION CHECK 11
5-3 TROUBLE SHOOTING 11
SPECIFICATIONS
6-1 SPECIFICATIONS 12
6-2 DIMENSIONS & OPTION 12
INTRODUCTION
1
1-1 BEFORE YOUR OPERATION


Produkt Specifikationer

Mærke: Optex
Kategori: Detektor
Model: AX-200TFR

Har du brug for hjælp?

Hvis du har brug for hjælp til Optex AX-200TFR stil et spørgsmål nedenfor, og andre brugere vil svare dig




Detektor Optex Manualer

Optex

Optex FLX-P-ST Manual

28 August 2024
Optex

Optex FLX-P-DT Manual

27 August 2024
Optex

Optex FX-360 Manual

10 August 2024
Optex

Optex FlipX Manual

5 August 2024
Optex

Optex RXC-ST Manual

4 December 2023
Optex

Optex OVS-01GT Manual

26 Marts 2023
Optex

Optex SIP-4010WF Manual

15 Januar 2023
Optex

Optex FD342 Manual

28 November 2022

Detektor Manualer

Nyeste Detektor Manualer

Protector

Protector WA-5.1 Manual

21 December 2024
Steinberg

Steinberg SBS-MD-9 Manual

16 December 2024
Steinberg

Steinberg SBS-MD-7 Manual

16 December 2024
Steinberg

Steinberg SBS-MD-2 Manual

16 December 2024
Steinberg

Steinberg SBS-MD-5 Manual

16 December 2024
Steinberg

Steinberg SBS-MD-3 Manual

15 December 2024
Steinberg

Steinberg SBS-MD-13 Manual

15 December 2024
Steinberg

Steinberg SBS-MD-6 Manual

15 December 2024
Perel

Perel EFL27 Manual

14 December 2024