Palmer Pedalbay 40 PB Manual

Palmer Ikke kategoriseret Pedalbay 40 PB

Læs nedenfor 📖 manual på dansk for Palmer Pedalbay 40 PB (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Palmer® is a registered brand of the Adam Hall Group
Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu-Anspach | Germany
Phone: +49 6081 9419-0 | .com adamhall
PEDALBAY® 40 PB
PEDALBOARD INCL. POWERBAR
SAFETY INFORMATION
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from
the equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. Use only sufficiently stable and compatible stands and/or mounts (for fixed instal-
lations). Make certain that wall mounts are properly installed and secured. Make
certain that the equipment is installed securely and cannot fall down.
7. During installation, observe the applicable safety regulations for your country.
8. Never install and operate the equipment near radiators, heat registers, ovens or
other sources of heat. Make certain that the equipment is always installed so that is
cooled sufficiently and cannot overheat.
9. Never place sources of ignition, e.g., burning candles, on the equipment.
10. Ventilation slits must not be blocked.
11. Do not use this equipment in the immediate vicinity of water (does not apply to
special outdoor equipment - in this case, observe the special instructions noted
below. Do not expose this equipment to flammable materials, fluids or gases.
12. Make certain that dripping or splashed water cannot enter the equipment. Do not
place containers filled with liquids, such as vases or drinking vessels, on the equipment.
13. Make certain that objects cannot fall into the device.
14. Use this equipment only with the accessories recommended and intended by
the manufacturer.
15. Open the device for changing the battery, do not modify this equipment.
16. After connecting the equipment, check all cables in order to prevent damage or
accidents, e.g., due to tripping hazards.
17. During transport, make certain that the equipment cannot fall down and possibly
cause property damage and personal injuries.
18. If your equipment is no longer functioning properly, if fluids or objects have gotten
inside the equipment or if it has been damaged in another way, switch it off
immediately and unplug it from the mains outlet (if it is a powered device). This
equipment may only be repaired by authorized, qualified personnel.
19. Clean the equipment using a dry cloth.
20. Comply with all applicable disposal laws in your country. During disposal of pack-
aging, please separate plastic and paper/cardboard.
21. Plastic bags must be kept out of reach of children.
22. If the equipment has been exposed to strong fluctuations in temperature (for
example, after transport), do not switch it on immediately. Moisture and conden-
sation could damage the equipment. Do not switch on the equipment until it has
reached room temperature.
23. Do not step on the power cord. Make certain that the power cable does not
become kinked, especially at the mains outlet and/or power adapter and the
equipment connector.
24. When connecting the equipment, make certain that the power cord or power
adapter is always freely accessible. Always disconnect the equipment from the
power supply if the equipment is not in use or if you want to clean the equipment.
Always unplug the power cord and power adapter from the power outlet at the
plug or adapter and not by pulling on the cord. Never touch the power cord and
power adapter with wet hands.
25. To disconnect the equipment from the power mains completely, unplug the power
cord or power adapter from the power outlet.
26. Unplug the power cord and power adapter from the power outlet if there is a risk
of a lightning strike or before extended periods of disuse.
CAUTION:
CAU TIO N
RIS K OF SELE CTRIC HOCK
DO N O NOT PE
There are no user serviceable parts inside. Have repairs carried out only by qualified
service personnel.
CAUTION – HIGH VOLUME LEVELS WITH AUDIO PRODUCTS!
This equipment is intended for professional use. Therefore, commercial use of this equip-
ment is subject to the respectively applicable national accident prevention rules and
regulations. As a manufacturer, Adam Hall is obligated to notify you formally about the
existence of potential health risks. Hearing damage due to high volume and prolonged
exposure: When in use, this product is capable of producing high sound-pressure levels
(SPL) that can lead to irreversible hearing damage in performers, employees, and
audience members. For this reason, avoid prolonged exposure to volumes in excess of
90 dB.
MANUFACTURER’S WARRANTY & LIMITATION OF LIABILITY
You can find our current warranty conditions and limitation of liability at: http://www.
adamhall.com/media/shop/downloads/documents/manufacturersdeclarations.pdf
To request warranty service for a product, please contact Adam Hall GmbH, Daimler
Straße 9, 61267 Neu-Anspach / Email Info@adamhall.com / +49 (0) 6081 / 9419-0
PROPER DISPOSAL OF THIS PRODUCT
(WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT)
(Valid in the European Union and other European countries with waste separation)
This symbol on the product, or the documents accompanying the product, indicates
that this appliance may not be treated as household waste. This is to avoid environmen-
tal damage or personal injury due to uncontrolled waste disposal. Please dispose of
this product separately from other waste and have it recycled to promote sustainable
economic activity.
DESCRIPTION
The PPEDALBAY40PB set combines the Palmer Pedalbay 40 and the Palmer
WTPB40 power supply with 8 outputs. It can be quickly swapped out and in-
stalled with the rear rails of the Pedalbay 40. This integrates the power supply
into the Pedalbay, thereby removing the need for separate transportation.
SPECIFICATIONS
Product number PWTPB40 – WT PB 40
Product type Power Supplies
Main connector Plug-in power supply
Input voltage 100 - 250 V
Outputs 8
Output connectors 2.1 x 5.5 mm
Material Aluminum
Surface Anodized, powder coated
Output voltage 12 V, 18 V, 9 V
Max. output current 2 A
Isolated outputs Yes
Polarity Center negative
Cord length 150 + 150 cm
Indicators Fault, Power
Controls Output voltage selector
Width 450 mm
Depth 50 mm
Height 24 mm
Weight 0.65 kg
Accessories (included) 5x DC cable straight to angled 16cm long, 9x
DC cable straight to angled 60cm long, hook-
and-loop tape, M6 Nuts, M8 Nuts, Power supply
PPEDALBAY40 – PEDALBAY
® 40
Product type Pedalboards
Material Aluminum
Surface Powder coated
Width of the Cross Bars 50 mm
Width 450 mm
Height 70 - 85 mm
Depth 305 mm
Weight Pedalbay 1.23 kg
Weight 3.83 kg
Accessories (included) 2x black elastic bands, allen key, approx.
2.5 m hook tape, soft carrying case with
shoulder strap
Features Adjustable cross bars, height-adjustable,
waterproof


Produkt Specifikationer

Mærke: Palmer
Kategori: Ikke kategoriseret
Model: Pedalbay 40 PB

Har du brug for hjælp?

Hvis du har brug for hjælp til Palmer Pedalbay 40 PB stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Palmer Manualer

Palmer

Palmer PAN 02 Manual

16 December 2024
Palmer

Palmer PLI-03 Manual

16 December 2024
Palmer

Palmer PLI04USB Manual

16 December 2024
Palmer

Palmer PLI-01 Manual

6 September 2024
Palmer

Palmer PLI-05 Manual

5 September 2024
Palmer

Palmer AoC Box XLRf Manual

5 September 2024
Palmer

Palmer RIVER ilm Manual

5 September 2024
Palmer

Palmer RIVER naab Manual

5 September 2024
Palmer

Palmer PAN 48 Manual

5 September 2024
Palmer

Palmer PAN 01 Manual

5 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer