Panasonic WV-Q189 Manual

Panasonic Ikke kategoriseret WV-Q189

Læs nedenfor 📖 manual på dansk for Panasonic WV-Q189 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 2 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
Operating Instructions
Included Installation Instructions
Corner Mount Bracket
Model No. WV-Q183 / WV-Q189
(Light Gray) (Fine Silver)
For U.S. and Canada:
Panasonic i-PRO Sensing Solutions
Corporation of America
800 Gessner Rd, Suite 700 Houston, TX 77024
https://www.security.us.panasonic.com/
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada
1-877-495-0580
https://www.panasonic.com/ca/
© Panasonic i-PRO Sensing Solutions Co., Ltd. 2019 sL1217-1109 PGQX2197YA Printed in China
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic i-PRO Sensing Solutions Co., Ltd.
Fukuoka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Before attempting to connect or install this product,
please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
Specifications
Ambient operating temperature: –50 °C to +60 °C {–58 °F to 140 °F}
Dimensions: 230 mm (L) × 246 mm (W) × 155 mm (H)
{9-1/16 inches (L) × 9-11/16 inches (H) × 6-3/32 inches (H)}
Mass: Approx. 1.3 k {2.87 lbs}g
Finish: Aluminum die cast
Light gray <WV-Q183>
Fine silver <WV-Q189>
Precautions
Refer installation work to the dealer.
Installation work requires technique and experiences. Failure to observe this may cause fire, electric
shock, injury, or damage to the product.
Be sure to consult the dealer.
The exclusively designed mount bracket shall be used.
Failure to observe this may cause a drop resulting in injury or accidents.
Use the exclusively designed mount bracket for installation.
Do not install this product in locations subject to vibration.
Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents.
Install this product in a location high enough to avoid people and objects from
bumping the product.
Failure to observe this may cause injury.
The measures of protection against a fall of this product shall be taken.
Failure to observe this may cause a drop resulting in injury.
If there is specified safety wire, please make sure to install it.
The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
Select an installation area that can support the total weight.
Selecting an inappropriate installation surface may cause this product to fall down or topple over,
resulting in injury or accidents.
Installation work shall be started after sufficient reinforcement.
Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.
Consult the dealer for the inspections.
Do not hang down from this product or use this product as a pedestal.
Failure to observe this may cause injury or accidents.
Do not use this bracket except with specified cameras or other brackets.
Failure to observe this may cause a drop resulting in injury or accidents.
Avoid installing this bracket in the locations where salt damage occurs or corro-
sive gas is produced.
Otherwise, the mounting portions will deteriorate and accidents such as a fall of this product may occur.
Do not install this product on a place that is greatly influenced by wind.
Installation on a place where the wind speed is 60 m/s {approx. 134 mph} or more may cause a fall
of the product resulting in injury or accidents.
Do not attempt to disassemble or modify this product.
Failure to observe this may cause a fall of the product resulting in injury or accidents.
Consult the dealer for the repair or inspections.
Do not rub the edges of metal parts with your hand.
Strong rubbing may cause injury.
The measures of protection against snowfall shall be taken.
Weight of snow may cause a fall of the product resulting in injury or accidents.
Protect the product against snowfall by installing under eaves.
Precautions for installation Installations/Connections
Panasonic assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation or operation inconsistent with
this documentation.
In order to prevent injury, the product must be securely mounted to the wall (corner)
according to Operating Instructions.
Installation area for this product
• Please consider the influence of vibration and wind at the installation site and mount the bracket
onto the wall with appropriate strength.
Installable corner Corner part of a vertical and right-angle wall:
• Do not mount the product on a plaster board or a wooden section because they are too weak.
If the product is unavoidably mounted on such a section, the section shall be sufficiently reinforced.
• After the bracket is mounted, please verify the following content once a year. In the event of
abnormality, please inform the dealer.
• Do not allow any slanting, distortion or offset in installation.
• Bracket should not have any serious rust or damage.
• Please refer to Panasonic's support website (https://security.panasonic.com/support/info/) for installa-
tion information of the bracket.
About the installation methods
• The bracket is specifically designed for installation onto a corner of the wall.
• Prepare mounting screws (M8 8 pcs.) and anchor bolts to be mounted on a wall separately.
• Select screws according to the material of the location that the bracket will be mounted to.
Minimum pull-out strength: 823 N {185 lbf} (per 1 pc.)
• After the installation is finished, please check if there are slackness or shaking of screws and rais-
ing of mount bracket.
In the event of abnormality, please tighten again.
Check before the installation.
Once the bracket is installed with a deformed mount bracket and/or damaged part, it could poten-
tially fall. Before the installation, please make sure to check the appearance of the bracket.
Do not place this product in the following places:
• Locations where a chemical agent is used such as a swimming pool.
• Locations that have a specific environment that is subject to an inflammable atmosphere or solvents.
• In areas by the sea or the seashore, regions with snow melt agent scattered and locations that
produce a corrosive gas such as volcanic areas and hot springs.
• Locations where the ambient operating temperature of camera is not within the specified range.
• Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines.
(This bracket is not designed for on-vehicle use.)
Screw tightening
• Make sure to tighten the screws (accessory) that fix camera or mount bracket onto WV-Q183/
WV-Q189.
• Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening
excessively.
• When a screw is tightened, make the screw at a right angle to the surface. After tightening the
screws or bolts, perform checks to ensure that the tightening is sufficient enough so that there is
no movement or looseness.
Make sure to remove this product if it will no longer be used.
Preface
WV-Q183/WV-Q189 (corner mount bracket) is designed to be used to install a camera or mount
bracket for camera to an external corner of building.
• WV-Q183 is different with WV-Q189 in color, and same in structure. This manual takes WV-Q189
as an example for explanation.
(In this illustration, fixing WV-Q122A to a corner by using WV-Q189 is taken as an example.)
Features
Parts and functions
WV-Q189
WV-Q122A
(Other optional
accessory)
M10 hexagon screws
(4 pcs. accessory)
M8 screw (8 pcs. locally
procured)
Standard accessories
<WV-Q189>
Operating Instructions (this document) 1 pc. .........................................................................................
Use the following accessories as the installation requires (use of all accessories together will likely not
be necessary):
Safety wire fixing bracket 1 pc. .............................................................................................................
M10 × 30 mm {1-3/16 inches} hexagon screws 5 pcs. ........................................................................
M6 × 16 mm {5/8 inches} hexagon screws 2 pcs. ................................................................................
M5 × 20 mm {25/32 inches} screws 5 pcs. ..........................................................................................
M4 × 16 mm {5/8 inches} screws 4 pcs. ..............................................................................................
M3 × 10 mm {13/32 inches} screws 2 pcs. ..........................................................................................
<WV-Q183>
Operating Instructions (this document) 1 pc. .........................................................................................
M10 × 30 mm {1-3/16 inches} hexagon screws 5 pcs. (1 spare) ..........................................................
Note:
• One spare is provided for each type of screw.
• A Hexagon wrench (procured locally) is needed when M10 or M6 hexagon screw is used.
(In this manual, hexagon socket head cap screw is described as hexagon screw.)
Install the mount bracket onto a corner
①Place WV-Q189 to the corner to be installed,
and marked the position of eight screw holes.
②According to the type of screw (M8, locally
procured), drill eight holes at the marked posi-
tion.
Note:
• -The corner must enough solid to sup
port the products installed on it.
WV-Q189
③Pass the cable to be connected with camera through the cable
access hole and pull out an adequate length as needed for the
camera.
Note:
• Please make sure the arrow on the
corner mount bracket is upward.
Cable
Cable access hole
④Use eight M8 screws (locally procured) to install
WV-Q189 onto the corner.
Minimum pull-out strength: 823 N {185 lbf} (per 1 pc.)
WV-Q189
M8 screw (8 pcs.
locally procured)
Upper mark:
Upper mark:
WV-Q189

Produkt Specifikationer

Mærke: Panasonic
Kategori: Ikke kategoriseret
Model: WV-Q189

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic WV-Q189 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Panasonic Manualer

Panasonic

Panasonic AK-HCU250PSJ Manual

25 December 2024
Panasonic

Panasonic DMW-LMCH62E Manual

21 December 2024
Panasonic

Panasonic DMW-GMC1 Manual

21 December 2024
Panasonic

Panasonic DMW-AVC1 Manual

21 December 2024
Panasonic

Panasonic SC-XH100 Manual

21 December 2024
Panasonic

Panasonic NB-W250 Manual

19 December 2024
Panasonic

Panasonic MultiShape ER-CKN3 Manual

19 December 2024
Panasonic

Panasonic DMW-YAGH Manual

11 December 2024
Panasonic

Panasonic ET-EMT850 Manual

7 December 2024
Panasonic

Panasonic ET-C1W300 Manual

7 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlona

Atlona AT-DVIF30S-IR Manual

29 December 2024
Atlona

Atlona AT-PRO3HD66M Manual

29 December 2024
Atlona

Atlona AT-3GSDI500 Manual

29 December 2024
BlueBuilt

BlueBuilt BBMAG2M Manual

29 December 2024
Atlona

Atlona AT-3GSDI-14 Manual

28 December 2024
Atlona

Atlona AT-COMP10SS Manual

28 December 2024
Atlona

Atlona AT-2VGA300SL Manual

28 December 2024
Atlona

Atlona AT-HD-V216 Manual

28 December 2024
Atlona

Atlona AT-VGA11S Manual

28 December 2024
True

True TC900 Manual

28 December 2024