Panasonic WV-SPV781 Manual
Panasonic
Bewakingscamera
WV-SPV781
Læs nedenfor 📖 manual på dansk for Panasonic WV-SPV781 (4 sider) i kategorien Bewakingscamera. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/4
● Switches the MONITOR OUT terminal output between NTSC and PAL.
Included Installation Instructions
PGQX1821YA Cs0615-1075 Printed in China
Two-dimensional
matrix barcode
(Data Matrix):
To our website
*2
IMPORTANT:
● Also waterproof the F 2P power cable (accessory),
E 4P alarm cable (accessory), and external connec-
tions in the same way.
● Stretch the tape to approx. twice its length (see the
illustration) and wind it around the cable. Insufficient
tape stretch causes insufficient waterproofing.
● To prevent the LAN cable hook from coming loose
easily, fit the D LAN connector cover (accessory)
onto the pigtail cable as illustrated, and then slide it in
the direction indicated by the arrow. The connector of
the LAN cable used with this camera must meet the
following restrictions.
Height when inserted (From bottom to hook.):
Max. 16 mm {5/8 inches}
Connector width: Max. 14 mm {9/16 inches}
● To install this product outdoors, be sure to waterproof
the cables.
Waterproof grade (IEC IP66 or equivalent) is applied
to this product only when it is installed correctly as
described in these operating instructions and appro-
priate waterproof treatment is applied.
The camera mount bracket is not waterproof.
Installation Guide
Network Camera
Model No. WV-SPV781L
● This manual describes the installation procedures, network camera installation, cable
connections, and eld-of-view adjustment.
● Before reading this manual, be sure to read the Important Information.
Major operating controls
The component names of the camera are as follows. Refer to the illustration when
installing or adjusting the camera.
Standard accessories Making connections
Important Information ............................... 1 pc.
Warranty card ........................................... 1 set
Code label*2 .............................................. 1 pc.
Installation Guide (this document) ............ 1 set
CD-ROM*1 ................................................. 1 pc.
Camera caution label................................ 1 pc.
*1
The CD-ROM contains the operating instructions and different kinds of tool software programs.
*2 This label may be required for network management. The network administrator shall retain
the code label.
*3 The audio/monitor output cable can be switched to be used as MONITOR OUT using the
software. The MONITOR OUT conversion plug is used to connect the camera to the audio/
monitor output cable and to convert a stereo mini jack (ø3.5 mm) {1/8 inches} into an RCA pin
output jack.
A Camera mount bracket cover ........... 2 pcs.
B Camera mount bracket cover fixing screw
(M3 x 6 mm {1/4 inches}) ................... 3 pcs.
(incl. 1 spare)
C Waterproof tape .................................. 1 pc.
D LAN connector cover ........................... 1 pc.
E 4P alarm cable .................................... 1 pc.
F 2P power cable .................................... 1 pc.
G MONITOR OUT conversion plug*3 ....... 1 pc.
H Safety wire .......................................... 1 pc.
I Wire lug fixing screw
M3 x 10 mm {3/8 inches} .................... 2 pcs.
(incl. 1 spare)
J Safety wire lug ..................................... 1 pc.
K Protection cover ................................... 1 pc.
L Adapter box .......................................... 1 pc.
M Mounting screws for adapter box (M5 × 20
mm {13/16 inches}) ............................. 5 pcs.
(of them, 1 for spare)
N Adapter box mounting screw
(M4 × 35 mm {1- 3/8 inches}) ............... 1 pc.
● How to initialize the camera
Follow the steps below to initialize the network camera.
1 Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from the camera.
When using an external power supply, disconnect the 2P power cable plug from the camera.
2
Turn on the power of the camera while holding down the INITIAL SET button, and then keep holding
down the button for 5 seconds or more. About 2 minutes after you have released the INITIAL SET but-
ton, the camera will start up and the settings including the network settings will be initialized.
● When data is being sent via the network camera Blinks green (accessing)
Turn off each system’s power supply before making a connection. Before making connections,
prepare the required peripheral devices and cables.
● When the camera is able to communicate with the Lights orange
connected device
● When an SD memory card is inserted and could Lights off → Blinks green →
be recognized Lights off
● When data can be saved after the SD memory card is inserted Lights off → Lights green
and the SD ON/OFF button is pressed (for less than 1 second)
● When data can be saved to the SD memory card Lights green
● When the SD memory card is removed after holding down
Lights green → Blinks green →
the SD ON/OFF button for about 2 seconds Lights off (recording)
Lights green →
Lights off (waiting for recording)
● When data cannot be saved to the SD memory card because Lights off
an abnormality was detected or the SD memory card is
configured not to be used
● When AF (Auto Focus) operation is being executed
Blinks red (about once per second)
● When the camera is being started Lights red
● When an SD memory card is recognized normally
Lights red → Lights off
● When the SD memory card slot is not used or an abnormality Lights red → Stays red
is detected in SD memory card after the camera has started
IMPORTANT:
● When the camera is initialized, the settings including the network settings will be initialized.
Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized.
● Before initializing the settings, it is recommended to write down the settings in advance.
● Do not turn off the power of the camera during the process of initialization. Otherwise, it may
fail to initialize and may cause malfunction.
IMPORTANT:
● Use all 4 pairs (8 pins) of the LAN cable (category 5 or better, straight).
● The maximum cable length is 100 m {328 feet}.
● Make sure that the PoE device in use is compliant with IEEE802.3af standard.
● When connecting both the 12 V DC power supply and the PoE device for power sup-
ply, 12 V DC will be used for power supply*.
* If a 12 V DC power supply and a PoE hub or router are used at the same time, net-
work connections may not be possible. In this case, disable the PoE settings. Refer
to the operating instructions of the PoE hub or router in use.
* Depending on the PoE device used, if you stop the 12 V DC power supply after
operating it and a PoE hub or router at the same time, the power supply may stop,
causing the camera to restart.
● When the LAN cable is disconnected once, reconnect the cable after around 2 sec-
onds. When the cable is quickly reconnected, the power may not be supplied from
the PoE device.
● When cables are used outdoors, there is a chance that they may be affected by light-
ning. In this case, install a lightning arrester just before where the LAN cable con-
nects to the camera.
Connect a LAN cable (category 5 or better, straight)
Waterproof treatment for the cable joint sections
When connecting to a network using a PoE hub
Microphone/line input cable
Connect a stereo mini plug (ø3.5 mm {1/8 inches}).
● Input impedance: Approx. 2 kΩ (unbalanced)
● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input) Less than
10 m {32.8 feet} (for line input)
● Recommended microphone: Plug-in power type (option)
• Supply voltage: 2.5 V ±0.5 V
• Recommended sensitivity of microphone: -48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
● Input level for line input: Approx. -10 dBV
* Use an external powered speaker.
Connect an external amplifier-embedded speaker to the audio/
monitor output cable
Connect a stereo mini plug (ø3.5 mm {1/8 inches}).*
● Output impedance: Approx. 600 Ω (unbalanced)
● Recommended cable length: Less than 10 m {32.8 feet}
● Output level: -20 dBV (can switch to monitor output)
IMPORTANT:
● Connect/disconnect the audio cables and turn on the power of the camera after turn-
ing off the power of the audio output devices. Otherwise, loud noise may be heard
from the speaker.
● Make sure that the stereo mini plug is connected to this cable. When a monaural mini
plug is connected, audio may not be heard. When connecting a monaural speaker
with amplifier, use a locally procured conversion cable (mono-stereo).
Adequate waterproof treatment is required for the cables when installing the camera with cables
exposed or installing it under the eaves.
The camera body is waterproof, but the cable ends are not waterproof. Be sure to use the sup-
plied waterproof tape at the points where the cables are connected to apply waterproof treatment
in the following procedure.
Failure to observe this or use of a tape other than the provided waterproof tape (such as a vinyl
tape) may cause water leakage resulting in malfunction.
Before starting the installation, check the entire system conguration.
The following illustration gives a wiring example of how to connect the camera to the network via
a PoE device (hub).
<LAN cable> < Alarm input/output cable, power cable, micro-
phone/line input cable, audio/monitor output
cable>
Stretch the tape to
approx. twice its length.
2 x
IMPORTANT:
● The adjustment monitor is used to adjust the field of view when installing or servicing
the camera. It is not provided for recording/monitoring use.
● Depending on the adjustment monitor, some characters (camera title, preset ID, etc.)
may not be displayed on the screen.
● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
● If a PoE hub is not used, each network camera must be connected to a 12 V DC
power supply.
● When using 12 V DC, power supply from a PoE hub or router is not required.
The hook engages
with the connector
terminal
D LAN connector cover
(accessory)
Sunshield
TILT lock screw
Camera
Arm
K Protection
cover (installed)
Front cover
Camera
Yawing
lock screw
H Safety wire
(accessory)
PAN lock screws
(2 pcs: The other is on the
opposite side)
L Adapter
box
(accessory)
A Camera mount
bracket covers
(2 pcs.) (accessory)
Camera
mount bracket
*1 SDXC/SDHC/SD memory card is described as SD memory card.
*2 Depending on the scanning application used, the Data Matrix may not be
able to be read correctly. In this case, access the site by directly entering the
following URL.
http://security.panasonic.com/pss/security/support/qr_sp_select.html
Connect the power cable
IMPORTANT:
● Use 12 V DC power supply that is insulated from the commercial AC power.
● Be sure to use the F 2P power cable (accessory) provided with this product.
● Be sure to fully insert the F 2P power cable (accessory) into the 12 V DC power sup-
ply terminal. Otherwise, it may damage the camera or cause malfunction.
● When installing the camera, make sure that excessive force is not applied to the
power cable.
● Be sure to use an AC adaptor compliant with the specifications (written in the indication
label on the bottom side of this unit) regarding power source and power consumption.
Power cable
12 V DC
Red Positive
Black Negative
<Required cable>
LAN cable (category 5 or better, straight)
Use a LAN cable (category 5 or better, cross) when directly connecting the camera to a PC.
Note:
● Off, input, and output of the external I/O terminal 2 and 3 can be switched by configur-
ing the setting. Refer to the Operating Instructions on the provided CD-ROM for further
information about the external I/O terminal 2 and 3 (ALARM IN2, 3) settings (“Off”,
“Alarm input”, “Alarm output”, “AUX output” or “DAY/NIGHT switching output”).
IMPORTANT:
● Be sure to use the E 4P alarm cable (accessory) provided with this product.
● Install external devices so that they do not exceed the ratings above.
● When using the external I/O terminals as the output terminals, ensure they do not
cause signal collision with external signals.
Connect the alarm input/output cable
<Ratings>
● ALARM IN1 (DAY/NIGHT IN), ALARM IN2, ALARM IN3
Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF: Open or 4 V - 5 V DC
ON: Make contact with GND (required drive current: 1 mA or more)
● ALARM OUT, AUX OUT (DAY/NIGHT OUT)
Output specification: Open collector output (maximum applied voltage: 20 V DC)
Open: 4 V - 5 V DC by internal pull-up
Close: Output voltage 1 V DC or less (maximum drive current: 50 mA)
* The default of EXT I/O terminals is “Off”.
E4P alarm cable (accessory)
PoE device (hub)
PC
Adjustment monitor
LAN cable
(category 5 or better, straight)
Microphone
Powered
speaker
Analog monitor
PC
SD memory card
slot
1 When the SD ON/OFF button is pressed for less than 1 second, the SD MOUNT indicator is lit green
and data can be saved to the SD memory card
*1
.
2 When the SD ON/OFF button is held down for about 2 seconds, the SD MOUNT indicator goes out,
and the SD memory card can be removed.
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic System Networks Co., Ltd.
Fukuoka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
The following parts are used during installation procedures.
GND (black)
ALARM IN3, AUX OUT, DAY/NIGHT OUT (gray)
(Alarm input 3, AUX output, DAY/NIGHT switching output)
ALARM IN2, ALARM OUT (red) (Alarm input 2, Alarm output)
ALARM IN1, DAY/NIGHT IN (green) (Alarm input 1/ DAY/NIGHT switching input)
RJ45 (female)
Network cable
LAN cable
(category 5 or better, straight)
E 4P alarm cable
(accessory)
Alarm input/output cable
(External I/O terminal)
Power cable
(12 V DC)
F 2P alarm cable
(accessory)
Microphone/line input cable (white)
Audio/monitor output cable (black)
Caution:
● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL
BE INCORPORATED TO THE EQUIPMENT POWERED
BY 12 V DC POWER SUPPLY.
● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL
1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/
UL/CSA 60950-1).
Wind the tape in a
half-overlapping manner. Wind the tape in a
half-overlapping
manner.
© Panasonic System Networks Co., Ltd. 2015
12 V DC
(red)
GND
(black)
Note:
● Use a thin, non-conductive tool to press the switch.
C
Waterproof tape (accessory)
C
Waterproof tape (accessory)
Connect the output cable of the AC adaptor to the
F
2P power cable (accessory).
Side B (Upper)
Side A (lower)
Rating label
Dehumidifying
device
MONITOR OUT jack
(Video Out terminal
Default:
For NTSC monitor)
NTSC/PAL switch
INITIAL SET button
SD ON/OFF button
SD MOUNT indicator
SD ERROR/AF indicator
ACT indicator
LINK indicator
AF (Auto Focus)
button
TELE button
(The camera zooms in.)
WIDE button
(The camera zooms out.)
Produkt Specifikationer
Mærke: | Panasonic |
Kategori: | Bewakingscamera |
Model: | WV-SPV781 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Panasonic WV-SPV781 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Bewakingscamera Panasonic Manualer
8 September 2024
1 September 2024
1 August 2024
25 Juli 2024
20 Juli 2024
19 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
Bewakingscamera Manualer
- Bewakingscamera Bosch
- Bewakingscamera Denver
- Bewakingscamera Sony
- Bewakingscamera Canon
- Bewakingscamera Samsung
- Bewakingscamera Extech
- Bewakingscamera TP-Link
- Bewakingscamera Philips
- Bewakingscamera Vitek
- Bewakingscamera Gigaset
- Bewakingscamera Logitech
- Bewakingscamera Emos
- Bewakingscamera Technaxx
- Bewakingscamera Waeco
- Bewakingscamera Grundig
- Bewakingscamera D-Link
- Bewakingscamera Arlo
- Bewakingscamera Motorola
- Bewakingscamera Toshiba
- Bewakingscamera Pyle
- Bewakingscamera Kodak
- Bewakingscamera Furrion
- Bewakingscamera Nedis
- Bewakingscamera Friedland
- Bewakingscamera Abus
- Bewakingscamera Planet
- Bewakingscamera Adj
- Bewakingscamera Hama
- Bewakingscamera Thomson
- Bewakingscamera Edimax
- Bewakingscamera Burg Wächter
- Bewakingscamera Clas Ohlson
- Bewakingscamera DataVideo
- Bewakingscamera Strong
- Bewakingscamera TRENDnet
- Bewakingscamera Smartwares
- Bewakingscamera Trevi
- Bewakingscamera Laserliner
- Bewakingscamera Blaupunkt
- Bewakingscamera JVC
- Bewakingscamera Honeywell
- Bewakingscamera Uniden
- Bewakingscamera Megasat
- Bewakingscamera EZVIZ
- Bewakingscamera König
- Bewakingscamera Elro
- Bewakingscamera Netgear
- Bewakingscamera Maginon
- Bewakingscamera Yale
- Bewakingscamera Nest
- Bewakingscamera Exibel
- Bewakingscamera Vaddio
- Bewakingscamera Digitus
- Bewakingscamera Zebra
- Bewakingscamera Alecto
- Bewakingscamera Flamingo
- Bewakingscamera Olympia
- Bewakingscamera B/R/K
- Bewakingscamera Marmitek
- Bewakingscamera Imou
- Bewakingscamera Nexxt
- Bewakingscamera APC
- Bewakingscamera Foscam
- Bewakingscamera Lorex
- Bewakingscamera Velleman
- Bewakingscamera LevelOne
- Bewakingscamera Marshall
- Bewakingscamera FLIR
- Bewakingscamera Perel
- Bewakingscamera Swann
- Bewakingscamera Vivotek
- Bewakingscamera JUNG
- Bewakingscamera ORNO
- Bewakingscamera ZyXEL
- Bewakingscamera Fortinet
- Bewakingscamera Tenda
- Bewakingscamera Eufy
- Bewakingscamera Ring
- Bewakingscamera M-e
- Bewakingscamera Overmax
- Bewakingscamera Y-cam
- Bewakingscamera Hikvision
- Bewakingscamera Monacor
- Bewakingscamera Ubiquiti Networks
- Bewakingscamera AVerMedia
- Bewakingscamera Reolink
- Bewakingscamera Grandstream
- Bewakingscamera Trebs
- Bewakingscamera Manhattan
- Bewakingscamera SPC
- Bewakingscamera Caliber
- Bewakingscamera Switel
- Bewakingscamera LogiLink
- Bewakingscamera Eminent
- Bewakingscamera Hanwha
- Bewakingscamera Brilliant
- Bewakingscamera Evolveo
- Bewakingscamera KJB Security Products
- Bewakingscamera Valueline
- Bewakingscamera Axis
- Bewakingscamera ACTi
- Bewakingscamera CRUX
- Bewakingscamera Aluratek
- Bewakingscamera Dahua Technology
- Bewakingscamera Chacon
- Bewakingscamera SereneLife
- Bewakingscamera ZKTeco
- Bewakingscamera Stabo
- Bewakingscamera EtiamPro
- Bewakingscamera First Alert
- Bewakingscamera Speco Technologies
- Bewakingscamera Boss
- Bewakingscamera Broan
- Bewakingscamera Avidsen
- Bewakingscamera Lindy
- Bewakingscamera Kogan
- Bewakingscamera Sitecom
- Bewakingscamera DiO
- Bewakingscamera Minox
- Bewakingscamera Intellinet
- Bewakingscamera V-TAC
- Bewakingscamera Qian
- Bewakingscamera August
- Bewakingscamera Schwaiger
- Bewakingscamera AViPAS
- Bewakingscamera UniView
- Bewakingscamera Alfatron
- Bewakingscamera Aqara
- Bewakingscamera Ernitec
- Bewakingscamera Setti+
- Bewakingscamera BZBGear
- Bewakingscamera AVer
- Bewakingscamera Profile
- Bewakingscamera Airlive
- Bewakingscamera Aritech
- Bewakingscamera KlikaanKlikuit
- Bewakingscamera Ednet
- Bewakingscamera Lumens
- Bewakingscamera Hombli
- Bewakingscamera Naxa
- Bewakingscamera Xavax
- Bewakingscamera Gira
- Bewakingscamera Interlogix
- Bewakingscamera DSC
- Bewakingscamera EverFocus
- Bewakingscamera Adesso
- Bewakingscamera Satel
- Bewakingscamera Notifier
- Bewakingscamera Beafon
- Bewakingscamera Videcon
- Bewakingscamera INSTAR
- Bewakingscamera Digital Watchdog
- Bewakingscamera Ganz
- Bewakingscamera MEE Audio
- Bewakingscamera Pelco
- Bewakingscamera Ebode
- Bewakingscamera Sonic Alert
- Bewakingscamera Linear PRO Access
- Bewakingscamera Summer Infant
- Bewakingscamera Topica
- Bewakingscamera Iiquu
- Bewakingscamera Verint
- Bewakingscamera Brinno
- Bewakingscamera Caddx
- Bewakingscamera Spyclops
- Bewakingscamera EKO
- Bewakingscamera Kguard
- Bewakingscamera Woonveilig
- Bewakingscamera Surveon
- Bewakingscamera Epcom
- Bewakingscamera Indexa
- Bewakingscamera Lutec
- Bewakingscamera VideoComm
- Bewakingscamera 3xLOGIC
- Bewakingscamera Inkovideo
- Bewakingscamera Weldex
- Bewakingscamera SecurityMan
- Bewakingscamera Canyon
- Bewakingscamera Aigis
- Bewakingscamera Exacq
- Bewakingscamera Brickcom
- Bewakingscamera Laxihub
- Bewakingscamera Securetech
- Bewakingscamera EFB Elektronik
- Bewakingscamera Illustra
- Bewakingscamera Atlona
- Bewakingscamera Syscom
- Bewakingscamera Tecno
- Bewakingscamera Night Owl
- Bewakingscamera Guardzilla
- Bewakingscamera Astak
- Bewakingscamera Blink
- Bewakingscamera Qoltec
- Bewakingscamera Digimerge
- Bewakingscamera Infortrend
- Bewakingscamera Vimtag
- Bewakingscamera Sonoff
- Bewakingscamera Gewiss
- Bewakingscamera Alula
- Bewakingscamera Insteon
- Bewakingscamera Costar
- Bewakingscamera Petcube
- Bewakingscamera I3International
- Bewakingscamera Turing
- Bewakingscamera Wasserstein
- Bewakingscamera Qolsys
- Bewakingscamera Control4
- Bewakingscamera Milesight
- Bewakingscamera GVI Security
- Bewakingscamera Conbrov
- Bewakingscamera HuddleCamHD
- Bewakingscamera Defender
- Bewakingscamera IOIO
- Bewakingscamera BIRDFY
- Bewakingscamera I-PRO
- Bewakingscamera DVDO
Nyeste Bewakingscamera Manualer
16 September 2024
16 September 2024
16 September 2024
16 September 2024
15 September 2024
15 September 2024
15 September 2024
15 September 2024
15 September 2024
15 September 2024