Panasonic WVSFN480 Manual

Panasonic Overvågningskamera WVSFN480

Læs nedenfor 📖 manual på dansk for Panasonic WVSFN480 (8 sider) i kategorien Overvågningskamera. Denne guide var nyttig for 12 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/8

B D E F

4321

Powered speaker Adjustment monitor

PoE device (hub)

Adjustment monitor

Microphone

Powered speaker

Microphone

LAN cable

(category 5 or better, straight)

LAN cable

(category 5 or better, straight)

* Can switch to monitor out

(select the [Setup] [Basic] tab, and then select [Monitor out])→

LAN cable (category 5

or better, straight)

Network Camera

Model No. WV-SFN480

Installation Guide

Included Installation Instructions

This manual describes the installation procedures, network camera installation, cable connections, ●

and the angle of view adjustment.

Before reading this manual, be sure to read the Important Information. ●

PGQX1666YA Cs1114-1124 Printed in China

For U.S. and Canada:

Panasonic System Communications

Company of North America,

Unit of Panasonic Corporation

of North America

www.panasonic.com/business/

For customer support, call 1.800.528.6747

Two Riverfront Plaza, Newark, NJ 07102-5490

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,

Ontario, L4W 2T3 Canada

(905)624-5010

www.panasonic.ca

For Europe and other countries:

Panasonic Corporation

http://panasonic.net

Panasonic System Networks Co., Ltd.

Fukuoka, Japan

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

Panasonic System Networks Co., Ltd. 2014

Standard accessories

Important Information ............................... 1 pc.

Installation Guide (this document) ............ 1 set

Warranty card ........................................... 1 set

CD-ROM*1 ................................................ 1 pc.

Code label*2 .............................................. 1 pc.

*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.

*2 This label may be required for network management. The network administrator shall retain the

code label.

The following parts are used during installation procedures.

A Attachment plate .................................. 1 pc.

B Bit (Hex wrench, screw size

6.35 mm {1/4 inches} T10) .................... 1 pc.

C Template A

.........................................

1 sheet

D Power cord plug ................................... 1 pc.

E External I/O terminal plug .................... 1 pc.

F Audio cable .......................................... 1 pc.

G Cable tie ............................................. 2 pcs.

(incl. 1 spare)

H Safety wire lug ..................................... 1 pc.

I Wire lug fixing screws

(M2.5 x 8 mm {5/16 inches}) .............. 2 pcs.

(incl. 1 spare)

J Desktop cover ...................................... 1 pc.

K Safety wire ........................................... 1 pc.

L Washer ................................................. 1 pc.

M Spring washer ...................................... 1 pc.

* The external I/O terminal plug and power cord plug are attached to the camera.

(Hex wrench, screw size

6.35 mm {1/4 inches} T10)

Direction marker for

installation “ TOP” J Desktop cover (accessory)

A Attachment plate (accessory)

Camera

Enclosure

Sub cover

Lens

SD memory

card slot

Major operating controls

The component names of the camera are as follows. Refer to the illustration when installing or

adjusting the camera.

How to initialize the camera ●

Follow the steps below to initialize the network camera.

q Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from

the camera. When using an external power supply, disconnect the power cable plug from

the 12 V DC power supply terminal.

w Turn on the power of the camera while holding down the INITIAL SET button, and then

keep holding down the button for 5 seconds or more. About 2 minutes later, the camera will

start up and the settings including the network settings will be initialized.

q When the SD ON/OFF button is pressed, data can be saved to the SD memory card.

w When the SD ON/OFF button is held down for about 2 seconds, the SD MOUNT indicator

goes out, and the SD memory card can be removed.

When data is being sent via the network camera Blinks green (accessing) ●

When the camera is able to communicate with the ●

Lights orange

connected device

When an SD memory card is inserted and could Lights off → Blinks green → ●

be recognized Lights off

When data can be saved after the SD memory card is Lights off → Lights green ●

inserted and the SD ON/OFF button is pressed

When data can be saved to the SD memory card Lights green ●

When the SD memory card is removed after holding down ●

Lights green → Blinks green → Lights off

the SD ON/OFF button for about 2 seconds

When data cannot be saved to the SD memory card Lights off ●

because an abnormality was detected or the SD memory

card is configured not to be used

When ABF (Auto Back Focus) operation is being executed ●

Blinks red (Interval of 1 time/ second)

When the set is being started Lights red ●

When an SD memory card ●*4 is recognized normally Lights red → Lights off

When the SD memory card slot is not used or an abnormality ●

Lights red → Stays red

is detected in SD memory card after the camera has started

IMPORTANT:

●When the camera is initialized, the settings including the network settings will be initial-

ized. Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not

be initialized.

Before initializing the settings, it is recommended to write down the settings in advance. ●

Do not turn off the power of the camera during the process of initialization. Otherwise, it ●

may fail to initialize and may cause malfunction.

SD MOUNT indicator

SD ERROR/ABF indicator

INITIAL SET button

SD ON/OFF button

ACT indicator

LINK indicator

Note:

The ACT indicator, Link indicator, SD ERROR/ABF indicator, and SD MOUNT indicator ●

inside the SD memory card slot cover can be turned off. (Indicators are set to light or blink

in the default settings.)

Turn off the indicators as required according to the installation environment. (

☞ Operating

Instructions (included in the CD-ROM))

ACT

indicator

LINK

indicator

SD ERROR/ABF

indicator

SD memory

card slot

External I/O terminals

EXT I/O*1

Network connector

10BASE-T/ 100BASE-TX*1

Audio cable connector

AUDIO I/O

12 V DC power supply terminal

12V IN*1

SD ON/OFF button

INITIAL SET button

SD memory card

slot cover

Data Matrix:

To our website*3

Image rotation gear Lens*2

Camera xing screw

Built-in

microphone

SD MOUNT

indicator

*1 The detailed specications on the right side of this page describe each terminal and cable.

*2 Do not directly touch the lens surface with your hands. Fingerprints, etc. may cause the image

quality to deteriorate. Also, the lens may slightly retract when its surface is touched. This is not

a malfunction.

Data Matrix is our website address converted into a two-dimensional barcode. Depending on

the scanning application used, the Data Matrix may not be able to be read correctly. In this

case, access the site by directly entering the following URL.

http://security.panasonic.com/pss/security/support/qr_sp_select.html

*4 SDXC/SDHC/SD memory card is described as SD memory card.

Making connections

Before making connections, prepare the required peripheral devices and cables, and turn off

each system's power supply.

Note:

Since the connector storage section ●

does not have a sufficient space, use

a LAN cable that does not exceed the

sizes described in the illustrations.

IMPORTANT:

Use all 4 pairs (8 pins) of the LAN cable ●(category 5 or better, straight, STP).

The maximum cable length is 100 m {328 feet}. ●

Make sure that the PoE device in use is compliant with IEEE802.3af standard. ●

When connecting both the 12 V DC power supply and the PoE device for power ●

supply, 12 V DC will be used for power supply.*

If a 12 V DC power supply and a PoE hub or router are used at the same time, *

network connections may not be possible. In this case, disable the PoE settings.

Refer to the operating instructions of the PoE hub or router in use.

Depending on the PoE device used, if you stop the 12 V DC power supply after *

operating it and a PoE hub or router at the same time, the power supply may stop,

causing the camera to restart.

When the LAN cable is disconnected once, reconnect the cable after around ●

2 seconds. When the cable is quickly reconnected, the power may not be supplied

from the PoE device.

Connect a LAN cable

Example of LAN cable connector

9 mm

{11/32 inches}

Straight section

30 mm {1-3/16 inches}

40 mm {1-9/16 inches}

13 mm {1/2 inches}

IMPORTANT:

Use 12 V DC power supply that is insulated from the commercial AC power. ●

Be sure to use the ●D power cord plug (accessory) provided with this product.

Be sure to fully insert the ●D power cord plug (accessory) into the 12 V DC power

supply terminal. Otherwise, it may damage the camera or cause malfunction.

When installing the camera, make sure that excessive force is not applied to the ●

power cable.

Be sure to use an AC adaptor compliant with the specifications (written in the indi- ●

cation label on the bottom side of this unit) regarding power source and power con-

sumption.

Caution:

A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED ●

TO THE EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.

ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or ●

LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).

Connect the power cable

Connect the output cable to the

D power cable plug (accessory).

q Loosen the screw of the power cable plug and strip 3 mm to 7 mm {1/8 inches to

9/32 inches} of the outer jacket. Expose the cable core (sufficiently twist any strand wires)

and then insert the cable into the power cable plug.

w Tighten the screw of the power cable plug. (Recommended tightening torque: 0.34 N·m

{0.25 lbf·ft})

Note:

Fully insert the stripped cable core into the ●D power cable plug (accessory), and

check that the cable core of the wiring is not protruding out and shorting with the

adjacent terminal.

When connecting an external power supply to the camera, use the AWG 16 - AWG 24 ●

single-wired or stranded wired cables.

LAN cable (category 5 or better, straight)

Use a LAN cable (category 5 or better, cross) when directly connecting the camera to a PC.

IMPORTANT:

The adjustment monitor is used for checking the adjustment of the angular field of ●

view when installing the camera or when servicing. It is not provided for recording/

monitoring use.

Depending on the monitor, some characters (camera title, preset ID, etc.) may not ●

be displayed on the screen.

Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX. ●

If a PoE hub is not used, each network camera must be connected to a 12 V DC ●

power supply.

When using 12 V DC, power supply from a PoE hub or router is not required. ●

IMPORTANT:

Be sure to use the ●E external I/O terminal plug (accessory) provided with this product.

Do not connect 2 wires or more directly to a terminal. When it is necessary to con- ●

nect 2 or more wires, use a splitter.

Install external devices so that they do not exceed the rating of the network camera. ●

When using the external I/O terminals as the output terminals, ensure they do not ●

cause signal collision with external signals.

Connect the alarm input/output cable

Connect the cables of external devices to the

E external I/O terminal plug (accessory).

Strip 8 mm to 9 mm of the outer jacket of the cable. Expose the cable core (sufficiently

twist any stand wires) and then insert the cable into the external I/O terminal plug E

(accessory).

Specification of cable (wire): AWG 20 - AWG 26, single-wired or stranded wired cables.

Push down the button of the desired terminal on the external I/O terminal plug with a ball-

point pen, and release the button when the cable of the external device is fully inserted

into the terminal hole.

Note:

Fully insert the stripped cable core into the ●E external I/O terminal plug (accessory),

and check that the cable core of the wiring is not protruding out and shorting with the

adjacent terminal.

ALARM IN1, ALARM IN2, ALARM IN3 ●

Input specication : No-voltage make contact input (4 V - 5 V DC, internally pulled up)

OFF : Open or 4 V - 5 V DC

ON : Make contact with GND (required drive current: 1 mA or more)

ALARM OUT, AUX OUT ●

Output specication

: Open collector output (maximum applied voltage: 20 V DC)

Open : 4 V - 5 V DC by internal pull-up

Close : Output voltage 1 V DC or less (maximum drive current: 50 mA)

* The default of external I/O terminals is “Off”.

4321

ALARM IN3, AUX OUT

(Alarm input 3, AUX output)

GND

ALARM IN1

(Alarm input 1)

ALARM IN2, ALARM OUT

(Alarm input 2, Alarm output)

External I/O terminal plug (accessory)E

button

Before starting the installation, check the entire system configuration. The following illustration

gives a wiring example of how to connect the camera to the network via a PoE device (hub).

When connecting to a network using a PoE hub

Connecting the microphone to the MIC IN plug of the audio cable

Connect a stereo mini plug (ø3.5 mm).

Input impedance: Approx. 2 kΩ (unbalanced) ●

Recommended cable length: Less than 1 m {3.28 feet} (for microphone input) ●

Less than 10 m {32.8 feet} (for line input)

Recommended microphone: Plug-in power type (option) ●

•Supply voltage: 2.5 V ±0.5 V

•Recommended sensitivity of microphone: -48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)

Input level for the line input: Approx. -10 dBV ●

IMPORTANT:

Connect/disconnect the audio cables and turn on the power of the camera after turning ●

off the power of the audio output devices. Otherwise, loud noise may be heard from

the speaker.

Make sure that the stereo mini plug is connected to this cable. When a monaural mini ●

plug is connected, audio may not be heard.

When connecting a monaural speaker with amplifier, use a locally procured conversion

cable (mono-stereo).

Connecting an external speaker with amplifier to the audio/monitor

output plug of the audio cable

Connect a stereo mini plug (ø3.5 mm).*

Output impedance : Approx. 600 Ω (unbalanced) ●

Recommended cable length : Less than 10 m {32.8 feet} ●

Output level : –20 dBV (can switch to monitor output) ●

* Use an external powered speaker.

As necessary, use a ●G cable

tie (accessory) to tie the cables

together.

Audio cable connector hook

* Press the hook of the con-

nector, and then remove the

audio cable connector.

Note:

Audio out is selected for the audio/monitor output plug by default. The plug can be ●

used for monitor out by selecting the [Setup]→[Basic] tab, and then selecting [Monitor

out]. (The ø3.5 mm monaural mini plug⇔RCA pin jack conversion cable is locally pro-

cured.)

Note:

Off, input, and output of the external I/O terminal 2 and 3 can be switched by con- ●

figuring the setting. Refer to the Operating Instructions on the provided CD-ROM

for further information about the external I/O terminal 2 and 3 (ALARM IN2, 3) set-

tings (“Off”, “Alarm input”, “Alarm output” or “AUX output”).

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	Overvågningskamera
Model:	WVSFN480

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic WVSFN480 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Panasonic Manualer

Panasonic WV-SFN480 Manual

2 Oktober 2024

Panasonic WV-CP630/G Manual

8 September 2024

Panasonic AW-HE20KE Manual

1 September 2024

Panasonic AW-UE100K Manual

27 August 2024

Panasonic AW-UR100 Manual

20 August 2024

Panasonic WV-SF438E Manual

1 August 2024

Panasonic AW-HN40H Manual

30 Juli 2024

Panasonic AW-UE150WE Manual

25 Juli 2024

Panasonic KX-HN6000 Manual

20 Juli 2024

Panasonic WV-SPW532L Manual

19 Juli 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Bosch MIC IP FUSION 9000i Manual

20 Februar 2025

Moen Flo 900-006 Manual

19 Februar 2025

Moen Flo 900-001 Manual

19 Februar 2025

IDIS DC-D4517RXP Manual

18 Februar 2025

IDIS DC-D4531WERX Manual

18 Februar 2025

IDIS DC-Y6516X Manual

18 Februar 2025

IDIS DC-D4217RX Manual

18 Februar 2025

IDIS DC-D4216WRX-A Manual

18 Februar 2025

IDIS DC-D4537RXA Manual

18 Februar 2025

IDIS DC-D4236WRX-A Manual

17 Februar 2025