Panasonic WVST165 Manual

Panasonic Overvågningskamera WVST165

Læs nedenfor 📖 manual på dansk for Panasonic WVST165 (2 sider) i kategorien Overvågningskamera. Denne guide var nyttig for 2 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Option

Precautions for use Precautions for Installation

Standard accessories

This system is designed to be used indoors. This product is not operable outdoors.

This product has no power switch.

When turning off the power, disconnect the power supply from the 12 V DC power supply or the

PoE device. (When using both the 12 V DC power supply and the PoE device for power supply, dis-

connect both the connections.)

To keep on using with stable performance

Do not use this camera in hot and humid conditions for a long time. Failure to observe this causes

component degradation resulting in life shortening of this product.

Do not expose this camera to direct heat sources such as a heater.

Do not touch the lens cover with your bare hands.

A dirty lens cover causes deterioration of picture quality.

Handle this camera with care.

Do not drop this camera, nor apply shock or vibration to this camera. Failure to observe this may

cause trouble.

About the PC monitor

Displaying the same image on a monitor for a long time may damage the monitor. It is recommend-

ed to use a screen-saver.

When an error is detected, this product will restart automatically.

This product will be inoperable for around 2 minutes after the restart just as when the power is turned on.

Product disposal/transfer

Data saved on this product or a storage device used with this product may lead to personal

information leakage. When it is necessary to dispose or give this product to someone, even when

for repair, make sure that there is no data on this product.

Cleaning this product body

Be sure to turn off the power before cleaning. Failure to observe this may cause injury. Do not use

strong abrasive detergent when cleaning this product. Otherwise, it may cause discoloration. When

using a chemical cloth for cleaning, read the caution provided with the chemical cloth product.

When the dirt is hard to remove, use a damp cloth and wipe the dirty areas. Then, wipe with a dry

cloth to remove any moisture.

Transmission interval

Image transmission interval may become slow depending on the network environment,

PC performance, shooting subject, access number, etc.

About SD memory card

When using an unformatted SD memory card, format it using this camera. Recorded data on the

⿟

SD memory card will be deleted when formatted. If an unformatted SD memory card or an SD

memory card formatted with other devices is used, this product may not work properly or perfor-

mance deterioration may be caused. Refer to the Operating Instructions (included in the

CD-ROM) for how to format a SD memory card.

When some SD memory cards are used with this product, the product may not work properly or

⿟

performance deterioration may be caused. Use the SD memory cards recommended.

Code label

The code labels (accessory) are required at inquiry for trouble. Use caution not to lose these labels.

It is recommended to paste one of the labels onto the CD-ROM case.

About the MOS image sensor

When continuously shooting a bright light source such as a spotlight, the color lter of the MOS

⿟

image sensor may have deteriorated and it may cause discoloration. Even when changing the

xed shooting direction after continuously shooting a spotlight for a certain period, the discolor-

ation may remain.

When shooting fast-moving subjects or performing panning/tilting operations, objects crossing

⿟

the shooting area may look to be bending askew.

AVC Patent Portfolio License

THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE

PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE

REMUNERATION TO

(i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR

(ii)

DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL

ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC

VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL

INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.

SEE HTTP://WWW.MPEGLA.COM

Flickering

Due to the inuence of lighting, ickering may sometimes happen. In this case, select “Indoor

scene” for “Light control mode”. Select “Indoor scene(50Hz)” or “Indoor scene(60Hz)” in accor-

dance with the power supply frequency in your locality. Refer to the Operating Instructions (included

in the CD-ROM) for further information about the setting.

Under extremely strong lighting, ickering may happen even when “Indoor scene” is selected for

“Light control mode”. When the brightness (illuminance) level on the screen is set to a relatively low

level with the [Brightness] buttons, ickering may frequently happen. In such cases, either of the fol-

lowing can reduce ickering.

Moderate the illumination intensities of objects by changing the camera direction.

⿟

Set the brightness (illuminance) level on the screen to a brighter level with the [Brightness] buttons.

White-out on images caused by the effect of light control mode

When “Indoor scene” is selected for “Light control mode”, the tone of the brighter parts on the

screen may be deteriorated than the case when “ELC” is selected.

Color blurring on detailed drawing patterns

When there are detailed drawing patterns on images, color blurring may happen over these parts.

Consumable parts

The following are consumables: Replace them in accordance with their lives. Their lives vary

depending on use environment and conditions. Lifetime is just an indication when using the camera

at +20 °C {68 °F}.

Panning motor, tilting motor, at cable for tilting: Approx. 3.7 million operations.

⿟

Lens and pan/tilt head

If a lens and pan/tilt head are not performed for a long period of time, the grease coating inside

these parts may become sticky. That may obstruct the parts from moving. To prevent this, move

the lens or pan/tilt head periodically.

Panasonic assumes no responsibility for injuries or property damage resulting from

failures arising out of improper installation or operation inconsistent with this

documentation.

This camera is designed to be used indoors.

This camera is not operable outdoors.

Do not expose this camera to direct sunlight for hours and do not install the product near a heater

or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction. Keep this

camera away from water and moisture.

Do not place this product in the following places:

Locations where it may get wet from rain or water splash

⿟

Locations where a chemical agent is used such as a swimming pool

⿟

Locations subject to humidity, dust, steam and oil smoke

⿟

Locations that have a specific environment that is subject to an inflammable atmosphere or solvents

⿟

Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated

⿟

Locations where corrosive gas is produced, Locations where it may be damaged by briny air

⿟

such as seashores

Locations where the temperature is not within the specied range (0°to +40°{32°to +104°F}).

⿟

Locations subject to vibrations (This product is not designed for on-vehicle use.)

⿟

Locations subject to condensation as the result of severe changes in temperature

⿟

Be sure to remove this product if it is not in use.

Before installation

When this camera is mounted on a wooden ceiling or a wall, use the wood screws (accessory,

⿟

Screw B). Screws to be used for other materials are not provided. Prepare the screws according

to the material, structure, strength and other factors of the mounting area and the total weight of

objects to be mounted.

Ensure that the mounting surface, anchor and screws are sufciently strong.

⿟

Do not mount this product on a plaster board or a wooden section because they are too weak. If

⿟

this product is unavoidably mounted on such a section, the section shall be sufciently rein-

forced.

Design and engineer the power supply system to turn on/off the power of this

product.

The product has no power switch. When installing the product, use a power supply

device equipped with the ON-OFF switch for servicing.

About the network connection

When connecting to a network using the network cable of this product, observe the following.

When wiring for the network, design and engineer not to be affected by thunder.

Screw tightening

The screws and bolts must be tightened with an appropriate tightening torque according to the

⿟

material and strength of the installation area.

Do not use an impact driver. Use of an impact driver may damage the screws or cause tighten-

⿟

ing excessively.

When a screw is tightened, make the screw at a right angle to the surface. After tightening the

⿟

screws or bolts, perform visual check to ensure tightening is enough and there is no backlash.

Procure xing screws separately.

The screws that secure this product are not supplied. Prepare them according to the material and

strength of the area where the product is to be installed.

Required pull-out capacity of a single screw/bolt is 294 N {66.09 lbf} or more.

Fall prevention measures

When the external safety wire is connected, select a connection point resulting in that nothing will

hit people after the stand is damaged.

Do not remove or loosen the internal camera screws.

Do not loosen the internal camera screws. Otherwise, water exposure may cause damage or mal-

function of camera, or camera dropping may result in injury.

Radio disturbance

When this product is used near TV/radio antenna, strong electric eld or magnetic eld (near a

motor, a transformer or a power line), images may be distorted and noise sound may be produced.

PoE (Power over Ethernet)

Use a PoE hub/device that is compliant with IEEE802.3af standard.

Router

When connecting this product to the Internet, use a broadband router with the port forwarding

function (NAT, IP masquerade). Refer to the Operating Instructions (included in the CD-ROM) for fur-

ther information about the port forwarding function.

Time & date setting

It is necessary to set the time & date before putting this product into operation. Refer to the

Operating Instructions on the provided CD-ROM for descriptions of how to perform the settings.

CPU: Intel® CoreTM 2 Duo 2.4 GHz or faster recommended

Memory: 512 MB or more (A minimum of 1 GB memory is required when using

Microsoft® Windows® 7 or Microsoft® Windows Vista®.)

Network interface: 10BASE-T/100BASE-TX 1 port

Monitor: Image capture size: 1024 x768 pixels or more

Color: 24-bit True color or better

OS: Microsoft® Windows® 7

Microsoft® Windows Vista®

Microsoft® Windows® XP SP3

Web browser: Windows® Internet Explorer® 9.0 (32-bit)

Windows® Internet Explorer® 8.0 (32-bit)

Windows® Internet Explorer® 7.0 (32-bit)

Microsoft® Internet Explorer® 6.0 SP3

Others: CD-ROM drive

(It is necessary to read the operating instructions and use the software on

the provided CD-ROM.)

DirectX® 9.0c or later

Adobe® Reader®

(It is necessary to view PDF le on the provided CD-ROM.)

IMPORTANT

When using a PC that does not meet the above requirements, displaying of images may

⿟

become slower or the web browser may become inoperable.

Microsoft Windows 7 Starter, Microsoft Windows Vista Starter and Microsoft Windows XP

⿟

Professional 64-bit Edition are not supported.

When using IPv6 for communication, use Microsoft Windows7 or Microsoft Windows Vista.

⿟

Note

Refer to “Notes on Windows

⿟®/ Internet Explorer®

versions” (included in the CD-ROM) for fur-

ther information about system requirements for a PC and precautions when using Microsoft

Windows 7, Microsoft Windows Vista or Internet Explorer.

⿟

If using Microsoft Windows XP, screen tearing* may occur when the shooting scene drastically

changes (for example, while shooting fast-moving subjects) due to the GDI restrictions of the OS.

* A phenomenon in which portions of the screen are displayed out of alignment.

For information on the operation verication of the supported operating systems and web

⿟

browsers, refer to our website at http://panasonic.net/pss/security/support/index.html.

System requirements for a PC

Main Unit (1 pc.)

Flexible Stand (1 pc.)

Screw A (1 pc.) Screw B (4 pcs.)

Washer S (1 pc.) Washer L (1 pc.) Safety Wire (1 pc.)

SD Card Cover (1 pc.)

Power cable plug (1 pc.)

−+

Installation Guide (this document) ........ (1 pc.)

Warranty card (P model) ....................... (1 pc.)

CD-ROM*1 ............................................ (1 pc.)

Code label*2 .......................................... (1 pc.)

*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.

*2 This label may be required for network management. The network administrator shall retain the

code label.

Installation Guide

Network Camera

Model No. WV-ST165/WV-ST162

WV-ST165E/WV-ST162E

PGQX1098ZA Cs1011-0

Main functions

● H.264 and JPEG triple encoding

A total of 3 outputs, comprising of 2 H.264 outputs and 1 JPEG output, can be provided.

● Power over Ethernet function

When connecting with a PoE (Power over Ethernet) device, power will be supplied by simply

connecting a LAN cable. (IEEE802.3af compliant)

● Adaptive darkness correction mode

Corrects the blacked-out parts of dark areas of objects that have different illumination intensities.

● Panning/tilting function and preset position function

A single camera provides wide area monitoring.

● Interactive communication with audio

By using the audio output connector and the microphone in connector, receiving audio from the

cameras on a PC and transmitting audio from the PC to the cameras is available.

● SDHC/SD memory card slot equipped

It is possible to save H.264 videos and JPEG images on the SDHC/SD memory card manually at

an alarm occurrence, during the period of the schedule, or on a web browser. It is also possible

to save JPEG images at a network failure occurrence. (Download is possible.)

Adobe, the Adobe logo, and Reader are either registered trademarks or trademarks of Adobe

⿟

Systems Incorporated in the United States and/or other countries.

Microsoft, Windows, Windows Vista, Internet Explorer, ActiveX, and DirectX are either registered

⿟

trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.

⿟

Intel and Intel Core are trademarks or registered trademarks of Intel Corporation in the United

⿟

States and other countries.

iPad, iPhone, and iPod touch are registered trademarks of Apple Inc., registered in the U.S. and

⿟

other countries.

All other trademarks identied herein are the property of their respective owners.

⿟

Trademarks and registered trademarks

Conrm the following items are included in the camera’s packaging.

You will need the following additional items to install and congure the camera.

[Locally procured]

PoE device (When supplying the power using the PoE device)

⿟

a PC (see the system requirements in the Important Information document)

⿟

a router

⿟

a LAN cable (CAT-5 straight cable)

⿟

AC Adaptor (1 pc.)

⿟

* FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.

As you will use this unit connected to a network, your attention is called to the following security risks.

A Leakage or theft of information through this unit

B Use of this unit for illegal operations by persons with malicious intent

C Interference with or stoppage of this unit by persons with malicious intent

It is your responsibility to take precautions such as those described below to protect yourself

against the above network security risks.

Use this unit in a network secured by a rewall, etc.

⿟

If this unit is connected to a network that includes PCs, make sure that the system is not infect-

⿟

ed by computer viruses or other malicious entities (using a regularly updated anti-virus program,

anti-spyware program, etc.).

Protect your network against unauthorized access by restricting users to those who log in with

⿟

an authorized user name and password.

Apply measures such as user authentication to protect your network against leakage or theft of

⿟

information, including image data, authentication information (user names and passwords), alarm

mail information, FTP server information and DDNS server information.

After the unit is accessed by the administrator, make sure to close the browser.

⿟

Change the administrator password periodically.

⿟

Do not install the camera in locations where the camera or the cables can be destroyed or dam-

⿟

aged by persons with malicious intent.

Before asking for repairs, check the symptoms with the following table.

Contact your dealer if a problem cannot be solved even after checking and trying the solution in the

table or a problem is not described below.

Symptom Cause/solution

Power is not turned on. u

Are the PoE device and the network cable of the camera

⿟

connected using a LAN cable?



Check whether the connection is appropriately established.

Depending on the PoE device, the power supply will stop

⿟

when the demanded power exceeds its total power limit for

all PoE ports.



Refer to the operating instructions of the PoE device in use.

Distributing, copying, disassembling, reverse compiling and reverse engineering of the software pro-

vided with this product are all expressly prohibited. In addition, exporting any software provided with

this product violating export laws is prohibited.

Precautions

Specications

Limitation of liability

Disclaimer of warranty

● Basic

Power source: PoE (IEEE802.3af compliant), 12 V DC

Power consumption:

PoE: 130 mA (Class 2 device), 12 V DC: 430 mA

Ambient operating temperature:

0 °C to +40 °C {32 °F to 104 °F}

Less than 90 % (no condensation)

Ambient operating humidity:

Monitor output:

VBS: 1.0 V [p-p]/75 Ω, composite (BNC), ø3.5 mm mini jack

EXT I/O terminal cable:

ALARM IN 1, ALARM IN 2/ ALARM OUT, ALARM IN 3/ AUX OUT, GND, 12 V DC

Microphone/Line input:

For microphone input

For line input

ø3.5 mm monaural mini jack

Input impedance: Approx. 2.2 kΩ

Applicable microphone: Plug-in power type

Supply voltage: 3.3 V ±0.5 V

Input level: Approx. –10 dBV

Audio output: ø3.5 mm stereo mini jack (monaural output)

Output impedance: Approx. 560 Ω

Line level

Dimensions: 100 mm (W) x 100 mm (H) x 74 mm (D) {3-47/50 inches (W) x 3-47/50

inches (H) x 2-23/25 inches (D)} (excluding projection)

Mass: Main body: 345 g {0.76 lbs}

Finish: Main body : PC/ABS resin, sail white

Dome section: Clear polycarbonate resin

● Camera

Image sensor: 1/4 type MOS image sensor

Effective pixels: Approx. 1.3 megapixels

Scanning area: 3.52 mm (H) × 2.64 mm (V) {7/50 inches (H) × 1/10 inches (V)}

Scanning system: Progressive

Minimum illumination: Color: 0.6 lx {0.06 footcandle}

(F2.2, Auto slow shutter: Off (1/30 s), Gain: On (High))

0.038 lx {0.0038 footcandle}

(F2.2, Auto slow shutter: max. 16/30 s, Gain: On (High))*

BW: 0.5 lx {0.05 footcandle}

(F2.2, Auto slow shutter: Off (1/30 s), Gain: On (High))

0.031 lx {0.0031 footcandle}

(F2.2, Auto slow shutter: max. 16/30 s, Gain: On (High))*

* Converted value

Wide dynamic range: On/Off

Face WDR: On/Off

Gain (AGC): On (Low)/ On (Mid)/ On (High)/ Off

Adaptive black stretch: On/Off

Light control mode setting:

Indoor scene (50Hz/60Hz)/ELC

ELC

(Maximum exposure time):

ELC(1/30 s), ELC(3/100 s), ELC(3/120 s), ELC(2/100 s), ELC(2/120 s),

ELC(1/100 s), ELC(1/120 s), ELC(1/250 s), ELC(1/500 s),

ELC(1/1000 s), ELC(1/2000 s), ELC(1/4000 s), ELC(1/10000 s)

Auto slow shutter: Off (1/30 s), Max. 2/30s, Max. 4/30s, Max. 6/30s, Max. 10/30s,

Max. 16/30s

Day & Night (electrical): Off/Auto

White balance: ATW1/ ATW2/ AWC

Digital noise reduction: High/Low

Video analytics

Face detection:

On/Off (with the XML notication setting)

Privacy zone: On/Off (up to 2 zones available)

Camera title on screen:

Up to 20 characters (alphanumeric characters, marks), On/Off

Video motion detection

(VMD alarm):

On/Off, (available at each preset)

● Lens

Zoom ratio: Extra zoom: 2x (under VGA resolution)

Digital (electronic) zoom:

8x (Max 16x combined with Extra Optical Zoom under VGA)

Focal length: 1.95 mm

Maximum aperture ratio:

1: 2.2

Focus range: ∞ - 0.5 m

Angular eld of view: Horizontal: 85°, Vertical: 68°

● Panning/tilting platform

Panning range: -47.5°- +47.5°

Panning speed:

Manual: Approx. 5 °/s - 80 °/s, Preset: Up to approx. 80 °/s

Tilting range: -45° to +10°

Tilting speed:

Manual: Approx. 5 °/s - 80 °/s, Preset: Up to approx. 80 °/s

Number of the preset positions:

Map shot: Preset map-shot

Self return:

10 s/ 20 s/ 30 s/ 1 min/ 2 min/ 3 min/ 5 min/ 10 min/ 20 min/ 30 min/ 60 min

Network security

WARNING

CAUTION

Turn the power off when cleaning this product.

• Failure to observe this may cause injury.

Refer installation work to the dealer.

• Installation work requires technique and experiences. Failure to observe this may cause re,

electric shock, injury, or damage to the product.

Be sure to consult the dealer.•

Stop the operation immediately when something is wrong with this product.

• When smoke goes up from the product, the smell of smoke comes from the product, or the

exterior of the product has deteriorated, continued use will cause a re or fall of the product

resulting in injury, or damage to the product.

Turn the power off immediately and contact qualied service personnel for service.•

Select an installation area that can support the total weight.

•

Selecting an inappropriate installation surface may cause this product to fall down or topple

over, resulting in injury.

Installation work shall be started after sufcient reinforcement.•

Periodic inspections shall be conducted.

• Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.

Consult the dealer for the inspections.•

The screws and bolts must be tightened to the specied torque.

• Failure to observe this may cause a drop resulting in injury or accidents.

Do not install this product in locations subject to vibration.

• Loosening of mounting screws or bolts may cause a fall of the product resulting in injury.

The measures of protection against a fall of this product shall be taken.

•

Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the safety wire.

Install this product in a location high enough to avoid people and objects from

•

bumping the product.

Failure to observe this may cause a drop resulting in injury or accidents.

Turn the power off when do wiring of this product.

•

Failure to observe this may cause electric shock. In addition, short circuit or wrong wiring may

cause re.

Do not attempt to disassemble or modify this product.

• Failure to observe this may cause re or electric shock. Consult the dealer for the repair or

inspections.

Do not insert any foreign objects.

• This could permanently damage this product. Turn the power off immediately and contact

qualied service personnel for service.

Do not use this product in an inammable atmosphere.

• Failure to observe this may cause an explosion resulting in injury.

Avoid installing this product in the locations where salt damage occurs or

•

corrosive gas is produced.

Otherwise, the mounting portions will deteriorate and accidents such as a fall of the product may occur.

Do not strike or give a strong shock to this product.

• Failure to observe this may cause re or injury.

Do not rub the edges of metal parts with your hand.

• Failure to observe this may cause injury.

Do not touch this product or the connected cables during thunder. (even in the

•

process of work)

Failure to observe this may cause electric shock.

Keep SDHC/SD memory cards (option) away from infants and children.

• Otherwise, they may swallow the cards by mistake.

In this case, consult a doctor immediately.•

● Network

Network: 10BASE-T/100BASE-TX, RJ45 connector

Resolution: WV-ST165

Imaging mode: 4:3

H.264 1280x960/ VGA (640x480)/ QVGA (320x240) max.30fps

JPEG 1280x960/ VGA (640x480)/ QVGA (320x240) max.30 fps

Imaging mode: 16:9

H.264 1280x720/ 640x360/ 320x180 max.30 fps

JPEG 1280x720/ 640x360/ 320x180 max.30 fps

WV-ST162

Aspect ratio: 4:3

H.264 SVGA(800x600)/ VGA(640x480)/ QVGA(320x240) max. 30 fps

JPEG SVGA(800x600)/ VGA(640x480)/ QVGA(320x240) max. 30 fps

Aspect ratio: 16:9

H.264 640x360/ 320x180, max. 30 fps

JPEG 640x360/ 320x180, max. 30 fps

Image compression

method:

H.264

mage quality: Low/ Normal/ Fine

Transmission type: Unicast/Multicast

Bit rate:

Constant bit rate/ Best effort:

64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/

768 kbps/ 1024 kbps/ 1536 kbps/ 2048 kbps/ 3072 kbps/

4096 kbps/ 8192 kbps

Frame rate:

1 fps/ 3 fps/ 5 fps/ 7.5 fps/ 10 fps/ 12 fps/ 15 fps/ 20 fps/

30 fps

JPEG Image quality: 0 SUPER FINE/ 1 FINE/ 2/ 3/ 4/ 5 NORMAL/

6/ 7/ 8/ 9 LOW (10 steps: 0-9)

Transmission type: PULL/PUSH

Transmission interval: 0.1 fps - 30 fps (JPEG frame rate will be restricted when displaying

both JPEG and H.264/ images.)

Audio compression

method:

G.726 (ADPCM) 32 kbps/ 16 kbps

G.711 64 kbps

Bandwidth control: Unlimited/ 64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/

768 kbps/ 1024 kbps/ 2048 kbps/ 4096 kbps/ 8192 kbps

Protocol: IPv6: TCP/IP, UDP/IP, HTTP, HTTPS, RTP, FTP, SMTP, DNS, NTP,

SNMP, DHCPv6, MLD, ICMP, ARP

IPv4: TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP, SMTP,

DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP, ICMP, ARP

Maximum concurrent

access number:

14 (Depends on network conditions)

FTP client: Alarm image transmission, FTP periodic transmission

Multi-screen: Up to 16 camera images can be displayed simultaneously on a multi-

screen. (Including the camera itself)

Compatible SDHC/

SD memory card (option):

Manufactured by Panasonic

SDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB

SD memory card: 256 MB, 512 MB, 1 GB, 2 GB

(except miniSD card and microSD card)

Cellular phone

compatibility:

JPEG image, panning/tilting/zoom control, AUX control (by access

level)

Mobile terminal compatibility:

iPad, iPhone, iPod touch (iOS 4.2.1 or later) (As of August, 2011)

*1 Transmission for 2 streams can be individually set in the same compression method.

● Optional accessories

User License Accessory (For H.264) BB-HCA8A (P model)

BB-HCA8CE (E model, Korea*) * Required in Korea

Troubleshooting

Important safety instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other appara-

tus (including ampliers) that produce heat.

9) Only use attachments/accessories specied by the manufacturer.

10) Use only with the cart, stand, tripod, bracket, or table specied by the

manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury

from tip-over.

S3125A

11) Unplug this apparatus during lightning storms or when unused for long periods of time.

12) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF

THE THIRD PARTY’S RIGHT.

THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL

ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE

IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).

IN NO EVENT SHALL Panasonic System Networks Co., Ltd. BE LIABLE TO ANY PARTY OR ANY

PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT,

FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:

(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL,

CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;

(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT

OPERATION OF THE USER;

(3) ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR OR

MODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF THE CAUSE OF THE

MALFUNCTION OR TROUBLE;

(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO

ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;

(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING

OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;

(6) ANY CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATION

BEING A PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF

THAT SURVEILLANCE-CAMERA’S PICTURE, INCLUDING SAVED DATA, FOR SOME

REASON, BECOMES PUBLIC OR IS USED FOR ANY PURPOSE;

(7) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.

For U.S. and Canada:

Panasonic System Networks Company of America,

Unit of Panasonic Corporation of North America

www.panasonic.com/business/

For customer support, call 1.800.528.6747

Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A.

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada

(905)624-5010

www.panasonic.ca

For Europe and other countries:

http://panasonic.net

Importer’s name and address to follow EU rules:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg F.R.Germany

WARNING:

To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture.

⿟

To prevent injury, this apparatus must be securely attached to the floor/wall/ceiling in accor-

⿟

dance with the installation instructions.

The installation shall be carried out in accordance with all applicable installation rules.

⿟

The connections should comply with local electrical code.

⿟

For U.S.A

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - spe-

cial handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/

For U.S. and Canada: WV-ST165/WV-ST162

For Europe and other countries: WV-ST165E/WV-ST162E

UL listed model No. WV-ST165/WV-ST162

For Canada

This Class A digital apparatus complies with Canadian ICES-003.

For U.S.A

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environ-

ment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

FCC Caution: To assure continued compliance, (example - use only shielded interface cables

when connecting to computer or peripheral devices). Any changes or modications not express-

ly approved by the party responsible for compliance could void the user’s authority to operate

this equipment.

For U.S.A

The model number and serial number of this product may be found on the surface of the unit.

You should note the model number and serial number of this unit in the space provided and

retain this book as a permanent record of your purchase to aid identication in the event of theft.

Model No. _________________________________

Serial No. __________________________________

For Europe

We declare under our sole responsibility that the product to which this declaration relates is in

conformity with the standard or other normative document following the provisions of Directive

2004/108/EC.

Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das sich diese Erklärung bezieht,

mit der folgenden Norm oder normativen Dokument übereinstimmt. Gemäß den Bestimmungen

der Richtlinie 2004/108/EC.

Nous déclarons sous notre propre responsabilité que le produit auquel se réfère la présente

déclaration est conforme á la norme spéciée ou à tout autre document normatif conformément

aux dispositions de la directive 2004/108/CE.

Nosotros declaramos bajo nuestra única responsabilidad que el producto a que hace referencia

esta declaración está conforme con la norma u otro documento normativo siguiendo las estipu-

laciones de la directiva 2004/108/CE.

Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente

dichiarazione risulta conforme al seguente standard o altro documento normativo conforme alle

disposizioni della direttiva 2004/108/CE.

Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft,

voldoet aan de volgende norm of ander normatief dokument, overeenkomstig de bepalingen van

Richtlijn 2004/108/EC.

Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i over-

ensstemmelse med standard eller andre normative dokumenter i følgebestemmelserne i direktiv

2004/108/EC.

Vi deklarerar härmed vårt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i

överensstämmelse med standarddokument eller annat normativt dokument som framställs i

direktiv 2004/108/EC.

Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa

seuraavaa standardia tai muuta ohjeellista asiakirjaa, jotka noudattavat direktiivin 2004/108/EC

säädöksiä.

Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overens-

stemmelse med følgende norm eller andre normgivende dokumenter som følger bestemmelsene

i direktiv 2004/108/EC.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean

that used electrical and electronic products and batteries should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old products and used batteries,

please take them to applicable collection points, in accordance with your national leg-

islation and the Directives 2002/96/EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the envi-

ronment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries,

please contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

Penalties may be applicable for incorrect disposal of this waste, in accordance with

national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer

or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these

items, please contact your local authorities or dealer and ask for the correct method

of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it

complies with the requirement set by the Directive for the chemical involved.

About the user manuals

There are 2 sets of operating instructions for the WV-ST165, WV-ST162 (P model), WV-ST165E,

WV-ST162E (E model) as follows.

Installation Guide: Explains how to install and connect devices, as well as how to connect and

⿟

congure the network.

Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how

⿟

to operate this camera.

Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.

When the Adobe® Reader® is not installed on the PC, download the latest Adobe Reader from the

Adobe web site and install it.

“WV-ST165, WV-ST162” or “ST165, ST162” shown in the instructions and illustrations used in

these operating instructions indicates the WV-ST165, WV-ST162, WV-ST165E, WV-ST162E.

The screens used in these operating instructions show the cases of P models.

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	Overvågningskamera
Model:	WVST165

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic WVST165 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Panasonic Manualer

Panasonic WV-SFN480 Manual

2 Oktober 2024

Panasonic WV-CP630/G Manual

8 September 2024

Panasonic AW-HE20KE Manual

1 September 2024

Panasonic AW-UE100K Manual

27 August 2024

Panasonic AW-UR100 Manual

20 August 2024

Panasonic WV-SF438E Manual

1 August 2024

Panasonic AW-HN40H Manual

30 Juli 2024

Panasonic AW-UE150WE Manual

25 Juli 2024

Panasonic KX-HN6000 Manual

20 Juli 2024

Panasonic WV-SPW532L Manual

19 Juli 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Hikvision DS-2CE12KF3T-LS Manual

18 December 2024

Bolin Technology B6-420 Manual

18 December 2024

Hikvision DS-2CE16U0T-LF Manual

18 December 2024

Hikvision DS-2CE10KF3T-LSYE Manual

18 December 2024

Hikvision DS-2CE10KF3T-LS Manual

18 December 2024

Hikvision DS-2CE76U0T-LMF Manual

18 December 2024

Hikvision DS-2CE12KF3T-LSYE Manual

18 December 2024

Hikvision DS-2CE72KF3T-LS Manual

18 December 2024

Hikvision DS-2CE17U0T-LF Manual

18 December 2024

Hikvision DS-2CE72KF3T-LSYE Manual

18 December 2024