Pioneer BCS-FS121 Manual

Pioneer Hjemmebiograf sæt BCS-FS121

Læs nedenfor 📖 manual på dansk for Pioneer BCS-FS121 (7 sider) i kategorien Hjemmebiograf sæt. Denne guide var nyttig for 27 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/7

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

DW845, DW847, DW849

Polishers

Polisseuses

Pulidoras

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. LÉASE ESTE INSTRUCTIVO ANTES ADVERTENCIA:

DE USAR EL PRODUCTO.

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more D WALT power tools: the yellow and black E

colorscheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box

configuration; and the array of lozenge-shaped humps on the surface of the tool.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D WALT • www.dewalt.comE

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word.

Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not

avoided, .will result in death or serious injury

WARNING: Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially

hazardous situation which, if not avoided, result in may property

damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D WALT TOOL, E

CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

General Safety Rules – For All Tools

WARNING! Read and understand all instructions. Failure to follow all

instructions listed below may result in electric shock, fire and/or serious personal

injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or

fumes.

• Distractions Keep bystanders, children, and visitors away while operating a power tool.

can cause you to lose control.

ELECTRICAL SAFETY

• Grounded tools must be plugged into an outlet properly installed and grounded in

accordance with all codes and ordinances. Never remove the grounding prong or

modify the plug in any way. Do not use any adaptor plugs. Check with a qualified

electrician if you are in doubt as to whether the outlet is properly grounded. If the tools

should electrically malfunction or break down, grounding provides a low resistance path to

carry electricity away from the user. Applicable only to Class I (grounded) tools.

• Double insulated tools are equipped with a polarized plug (one blade is wider than the

other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully

in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to

install a polarized outlet. Do not change the plug in any way. Double insulation

eliminates the need for the three wire grounded power cord and grounded power supply

system. Applicable only to Class II (double insulated) tools.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged

cords immediately. Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked “W-A”

or “W.” These cords are rated for outdoor use and reduce the risk of electric shock. When

using an extension cord, be sure to use one heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge

number, the heavier the cord.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG

Than Than

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.

A moment of inattention while operating power tools may result in serious personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long

hair can be caught in moving parts. Air vents often cover moving parts and should also be

avoided.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with

the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments, changing

accessories, or storing the tool. Such preventative safety measures reduce the risk of

starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the

hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,

with sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of electric shock or injury.

Additional Specific Safety Instructions for Polishers

• Always use proper guard with grinding wheel. A guard protects operator from broken

wheel fragments and wheel contact.

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

• Always use eye protection. All users and bystanders must wear eye protection that

conforms to ANSI Z87.1.

• Clean out your tool often, especially after heavy use. Dust and grit containing metal

particles often accumulate on interior surfaces and could create an electric shock hazard.

• Do not operate this tool for long periods of time. Vibration caused by the operating action

of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide

extra cushion, take frequent rest periods, and limit daily time of use.

• Do not allow any loose portion of the polishing bonnet or its attachment strings to spin

freely. Tuck away or trim any loose attachment strings. Loose and spinning attachment

strings can entangle your fingers or snag on the workpiece.

Causes and Operator Prevention of Kickback

• Kickback is a sudden reaction to a pinched, bound or misaligned wheel, wire brush or

flap disc causing an uncontrolled cut-off tool to lift up and out of the workpiece toward the

operator.

• When the wheel is pinched or bound tightly by the workpiece, the wheel stalls and the motor

reaction drives the unit rapidly back toward or away from the operator.

• Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and

can be avoided by taking proper precautions as given below:

• Maintain a firm grip with both hands on the unit and position your body and arm to

allow you to resist kickback forces. Kickback forces can be controlled by the operator,

if proper precautions are taken.

• When wheel is binding, or when interrupting a cut for any reason, release the trigger

and hold the unit motionless in the material until the wheel comes to a complete

stop. Never attempt to remove the unit from the work or pull the unit backward while

the wheel is in motion or kickback may occur. Investigate and take corrective actions

to eliminate the cause of wheel binding.

• When restarting a cut-off accessory in the workpiece, check that the wheel is not

engaged into the material. If wheel is binding, it may walk up or kickback from the

workpiece as the tool is restarted.

• Support large panels to minimize the risk of wheel pinching and kickback. Large

panels tend to sag under their own weight. Support must be placed under the panel on

both sides, near the line of cut and near the edge of the panel.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.

Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY

EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects, or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Use extra care when working into a corner because a sudden, sharp movement

of the grinder may be experienced when the wheel or other accessory contacts a secondary

surface or a surface edge.

Produkt Specifikationer

Mærke:	Pioneer
Kategori:	Hjemmebiograf sæt
Model:	BCS-FS121
Vekselstrømsindgangsspænding:	110-240 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Brugervejledning:	Ja
Produktfarve:	Sort
3D:	Ja
DLNA-certificeret (Digital Living Network Alliance):	Ja
Format til analogt signal:	NTSC,PAL
Udgangseffekt (RMS):	550 W
Lyddekodere:	Dolby Digital,Dolby Digital Plus,Dolby Pro Logic II,Dolby TrueHD,DTS,DTS-HD,DTS-HD Master Audio
Ethernet LAN-porte (RJ-45):	1
Ethernet LAN:	Ja
Understøttede videoformater:	AVCHD,DIVX,FLV,MKV,WMV
Understøttede lydformater:	AAC,FLAC,LPCM,MP3,MP4,WMA
Strømforbrug (standby):	0.5 W
Strømforbrug (typisk):	105 W
Hurtig start guide:	Ja
Kabler inkluderet:	Vekselstrøm
Audio Return Channel (ARC):	Ja
Understøttede billedformater:	JPG
Fjernbetjening inkluderet:	Ja
Lyd-output kanaler:	2.1 kanaler
LED-indikatorer:	Ja
Understøttede disktyper:	BD,BD-R,BD-RE,BD-ROM,CD,CD-R,CD-RW,DVD,DVD+R,DVD+RW,DVD-R,DVD-RW
Full HD:	Ja
HDMI:	Ja
Indbygget HDD:	Ingen
USB version:	2.0
Antal USB-porte:	2
RDS Tuner inkluderet:	Ja
MP3-afspilning:	Ja
CD-RW-afspilning:	Ja
Mikrofonindgang:	Ja
Strøm-LED:	Ja
Lyd (L, R) indgang:	1
Firmware kan opgraderes:	Ja
Sammensat videoudgang:	1
Afspilning af diskformater:	Blu-Ray audio,Blu-Ray video,CD audio,CD video,SACD
Kampatibilitet med Apple-docking:	Ikke understøttet
Subwoofer RMS-effekt:	250 W
HSMI-indgang:	2
Antal HDMI-udgange:	1
Subwoofer type:	Passiv subwoofer
Optisk diskafspiller type:	Blu-Ray afspiller
Digital akustisk og optisk indgang:	2
Dimensioner for hovedenhed (BxDxH):	430 x 345 x 64 mm
Hovedenhed vægt:	3400 g
Subwoofer dimensioner (BxDxH):	200 x 270 x 340 mm
Subwoofer vægt:	3400 g
Karaoke:	Ja
Antal optiske diske:	1 diske
Subwoofer-impedans:	3 ohm (Ω)
Diskindlæsningstype:	Bakke
Fronthøjttaler vægt:	300 g
Fronthøjttaler dimensioner (BxDxH):	95 x 90 x 80 mm
Video D/A-konverter (DAC):	12-bit/148MHz
Slideshow:	Ja