Planet FGSD-1821P Manual

Planet Skifte FGSD-1821P

Læs nedenfor 📖 manual på dansk for Planet FGSD-1821P (4 sider) i kategorien Skifte. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/4
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 16-/24-Port 10/100TX 802.3at PoE
+ 2-Port 10/100/1000T + 1-Port shared 1000X SFP Desktop Switch,
FGSD-1821P or FGSD-2621P. “802.3at PoE+ Switch” mentioned in this
Guide refers to the FGSD-1821P or FGSD-2621P
Open the box of the 802.3at PoE+ Switch and carefully unpack it. The
box should contain the following items
The 802.3at PoE+ Switch x 1 User’s Manual x 1 Power Cord x 1
SFP Dust Cap
x 1 Screws x 8 Rack-mounting
Brackets x 2 Rubber Feet x 4
If any of these pieces are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the original
packing material, and use them again to repack the product in case
there is a need to return it to us for repair.
Per 10/100BASE-TX Port
LED Color Function
10/100
LNK/ACT Green
Lights to indicate the link through that
port is successfully established.
Blinks to indicate that the Switch is
actively sending or receiving data over
that port.
PoE in Use Amber Lights to indicate the port is providing
PoE DC in-line power.
Per 10/100/1000BASE-T Port
LED Color Function
10/100/1000
LNK/ACT Green
Lights to indicate the link through that
port is successfully established.
Blinks to indicate that the Switch is
actively sending or receiving data over
that port.
1000BASE-X SFP Port
LED Color Function
1000
LNK/ACT Green
Lights to indicate the link through that port
is successfully established at 1000Mbps.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
3 Hardware Installation
3.1 Rack Mounting
To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the
instructions described below.
Step 1: Place your 802.3at PoE+ Switch on a hard at surface, with
the front panel positioned towards your front side.
Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+
Switch with supplied screws attached to the package. Figure
3-1 shows how to attach brackets to one side of the 802.3at
PoE+ Switch.
17
1000X SFP
LNK
PoE-in-Use
ACT
Standard
VLAN
Extend
PWR
PoE Max
2 6
4 8 10 14
12 16
1 5
3 7 9 13
11 15
18
17
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
Figure 3-1: Attaching the Brackets to the 802.3at PoE+ Switch.
Caution
You must use the screws supplied with the mounting
brackets. Damage caused to the parts by using incorrect
screws would invalidate the warranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the
opposite side.
Standard Mode (default)
Power
PoE IP Camera
PoE
100 meters (328 feet)
PoE
100BASE-TX UTP with PoE
FGSD-1821P
Standard
VLAN
Extend
VLAN Isolation Mode
NVR
PC
Ports 1 to 16
Access Denied
PoE
PoE
PoE
PoE
100BASE-TX UTP with PoE
FGSD-1821P
IP Camera
IP Camera
IP Camera
Ports 17~18 and SFP Port 17
to Ports 1~16 Access Permitted
1000BASE-T UTP
Standard
VLAN
Extend
Extend Mode
Ports 1 to 8
Power
250 meters (820 feet)
PoE
PoE
10BASE-T UTP with PoE
PoE IP Camera
FGSD-1821P
Standard
VLAN
Extend
2. Hardware Introduction
2.1 Front Panel
The front panel of the 802.3at PoE+ Switch consists of 16/24 auto-
sensing 10/100BASE-TX RJ45 ports, 2 auto-sensing 10/100/1000BASE-T
RJ45 ports and 1 1000BASE-X SFP port. The LED Indicators are also
located on the front panel of the 802.3at PoE+ Switch.
17
1000X SFP
LNK
PoE-in-Use
ACT Standard
VLA N
Ex tend
PWR
PoE Ma x
2 64 8 10 1412 16
1 53 7 9 1311 15
18
17
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
Figure 2-1: FGSD-1821P Switch Front Panel
1000X SFP
25
1 2 3 4 5 6 7 8 9 10 12 13 14 1 5 16 17 18 19 2 0 21 22 23 2411
26
Standa rd
VLA N
Ex tend
LNK ACT
4 128 16 20 24
3 117 15 19 23
2 106 14 18
PoE Max
22
1 95 13 17 PWR21
26
25
PoE -
in-Use 26
Figure 2-2: FGSD-2621P Switch Front Panel
2.2 LED Indicators
System
LED Color Function
PWR Green Lights to indicate the Switch has power.
PoE
(max.) Green
O to indicate the PoE power is less than 80%
of total power.
Lights to indicate the PoE power is above
80%.
2.3 Multiple Functions of DIP Switch
The front panel of the 802.3at PoE+ Switch provides one DIP switch for
Standard VLAN Extend, or mode selection. The detailed descriptions
are shown in the following table.
DIP Switch Mode Function
Standard
VLAN
Extend
This mode makes the 802.3at PoE+ Switch
operate as a and all PoE+ general switch
ports operate at 10/100Mbps auto-negotiation.
All ports can communicate with one another.
Standard
VLAN
Extend
This mode makes the 802.3at PoE+ Switch
operate as a switch and VLAN isolation
For FGSD-1821P:
1. Ports 1 to 16 will isolate respectively.
2. Ports 1 to 16 can only communicate with
ports 17~18 (uplink ports) and SFP port 17.
For FGSD-2621P:
1. Ports 1 to 24 will isolate respectively.
2. Ports 1 to 24 can only communicate with
ports 25~26 (uplink ports) and SFP port 26
Standard
VLAN
Extend
This mode makes the 802.3at PoE+ Switch
operate as a switch and Long Reach PoE
1. Ports 1 to 8 support farthest transmission
distance of up to 250 meters
2. Ports 1 to 8 have a data rate of 10Mbps
3. All ports can communicate with one
another.
Note
Please select a DIP switch mode before powering on the
802.3at PoE+ Switch.
2.4 Rear Panel
The rear panel of the 802.3at PoE+ Switch indicates an AC power
socket, which accepts input power from 100 to 240V AC, 50-60Hz, 5A.
50/60Hz
100-240V , 5A max.
Figure 2-3: Switch Rear Panel
AC Power Receptacle
Power
Notice
The device is a power-required device, which means
it will not work till it is powered. If your networks
should be active all the time, please consider using UPS
(uninterrupted power supply) for your device. It will
prevent you from network data loss or network downtime.
Power
Notice
In some areas, installing a surge suppression device may
also help to protect your 802.3at PoE+ Switch from being
damaged by unregulated surge or current to the 802.3at
PoE+ Switch or the power adapter.
Step 5: After the brackets are attached to the 802.3at PoE+ Switch,
use suitable screws to securely attach the brackets to the
rack, as shown in Figure 3-2.
17
1000X SF P
LNK
PoE-in-Us e
ACT
Standa r d
VLAN
Exten d
PWR
PoE Max
2 6
4 8 10 14
12 16
1 5
3 7 9 13
11 15
18
17
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
Figure 3-2: Mounting the 802.3at PoE+ Switch in a Rack
Step 6: Connect your 802.3at PoE+ Switch to 802.3af/802.3at
complied PDs and other network devices.
A. Connect one end of a standard network cable to the
10/100/1000BASE-T RJ45 ports on the front panel of the 802.3at
PoE+ Switch.
B. Connect the other end of the cable to the network devices such as
printer servers, workstations or routers, etc.
Step 7: Supply power to the 802.3at PoE+ Switch.
A. Connect one end of the power cable to the 802.3at PoE+ Switch.
B. Connect the power plug of the power cable to a standard wall
outlet.
When the 802.3at PoE+ Switch receives power, the power LED should
remain solid Green.


Produkt Specifikationer

Mærke: Planet
Kategori: Skifte
Model: FGSD-1821P

Har du brug for hjælp?

Hvis du har brug for hjælp til Planet FGSD-1821P stil et spørgsmål nedenfor, og andre brugere vil svare dig




Skifte Planet Manualer

Planet

Planet GSD-1121XP Manual

18 September 2024
Planet

Planet BSP-115PV-15A Manual

7 September 2024
Planet

Planet BSP-115HP-5A Manual

5 September 2024
Planet

Planet IGTP-805AT Manual

3 September 2024
Planet

Planet IPM-16230 Manual

3 September 2024
Planet

Planet FSD-804P Manual

3 September 2024
Planet

Planet UPOE-1600G Manual

1 September 2024
Planet

Planet WS-1032P Manual

1 September 2024

Skifte Manualer

Nyeste Skifte Manualer

Netgear

Netgear GS110TPP Manual

15 Oktober 2024
Lancom

Lancom CS-8132F Manual

7 Oktober 2024
Lancom

Lancom YS-7154CF Manual

7 Oktober 2024
Perel

Perel E305W3-G Manual

5 Oktober 2024
Tork

Tork SS720A Manual

5 Oktober 2024
Black Box

Black Box ACX300-R Manual

4 Oktober 2024
Edimax

Edimax IGS-1105P Manual

4 Oktober 2024