Planet IGS-504PT Manual


Læs nedenfor 📖 manual på dansk for Planet IGS-504PT (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/4
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET IGS-504PT Industrial 5-Port
Gigabit Ethernet Switch with 4 PoE+ ports. The interfaces of
these models are shown below:
In the following section, the term Industrial PoE+ Switch”
means the IGS-504PT. Open the box of the Industrial PoE+
Switch and carefully unpack it. The box should contain the
following items:
Industrial PoE+ Switch x 1 Users Manual x 1
Wall-mount Kit x 1 DIN-rail Kit x 1 RJ45 Dust Caps x 5
If any of these are missing or damaged, please contact your
dealer immediately.
Switch Specications
Switch
Architecture Store-and-Forward
Switch Fabric 10Gbps
Throughput
(packet per
second)
7.4Mpps@64bytes
Address Table 2K entries
Jumbo Frame 9Kbytes
Flow Control Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Power over Ethernet
PoE Standard
IEEE 802.3at Power over Ethernet Plus/PSE
Backward compatible with IEEE 802.3af
Power over Ethernet/PSE
PoE Power
Supply Type End-span
Power Pin
Assignment 1/2(+), 3/6(-)
PoE Power
Output
Per port 48-54V DC
Max. 30 watts@54V DC
Max. 15 watts@48V DC
PoE Power
Budget
Max. 120 watts@54V DC
Max. 60 watts@48V DC
Max. Number
of Class 4 PDs 4
3.3 Switch Upper Panel
The upper panel of the Industrial PoE+ Switch consists of one
terminal block connector within two DC power inputs.
Figure 3-2 shows the upper panel of the Industrial PoE+
Switch.
DC Input Range:
48-54V
, 3A max.
V1+ V2+
PWR1 PWR2
1 2 3 4
Figure 3-2: Industrial PoE+ Switch Upper Panel
3.4 Wiring the Power Inputs
The 4-contact terminal block connector on the top panel of
Industrial PoE+ Switch is used for two DC redundant power
inputs. Please follow the steps below to insert the power wire.
When performing any of the procedures like
inserting the wires or tightening the wire-clamp
screws, make sure the power is OFF to prevent
from getting an electric shock.
3. Hardware Introduction
3.1 Switch Front Panel
P1 P2
1
2
3
4
5
ACTLNK
PoE-in-Use
Gigabit Ethernet TP Interface
10/100/1000BASE-T copper, RJ45
twisted-pair: Up to 100 meters.
Figure 3-1:
IGS-504PT Front View
2.ProductSpecications
Model IGS-504PT
Hardware Specications
Copper Ports 5 10/100/1000BASET RJ45 auto-MDI/MDI-X
ports
PoE Injector
Ports
4 ports with 802.3at PoE+ injector function
(Ports 1 to 4)
PoE Budget 120W maximum@75 degrees C
Connector Removable 4-pin terminal block
Pin 1/2 for Power 1; Pin 3/4 for Power 2
Power
Requirements
48~54V DC, 3A (max.)
Redundant power with reverse polarity
protection function
Power
Consumption
DC 48V:
Max. 0.48 watts/1.63BTU (System)
Max. 62.88 watts/214.5BTU (Full Loading)
DC 54V:
Max. 0.54 watts/1.84BTU (System)
Max. 123.12 watts/420BTU (Full Loading)
Dimensions
(W x D x H) 30 x 70 x 104 mm
Weight 260g
Enclosure IP30 metal case
Installation DIN-rail kit and wall-mount kit
ESD Protection 6KV
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Stability
Testing
IEC 60068-2-32 (free fall)
IEC 60068-2-27 (shock)
IEC 60068-2-6 (vibration)
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3az Energy Ecient Ethernet (EEE)
IEEE 802.3at Power over Ethernet Plus PSE
IEEE 802.3af Power over Ethernet Plus
IEEE 802.1p Class of Service
Environment
Temperature Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity Operating: 5~90% (non-condensing)
Storage: 5~90% (non-condensing)
3.2 LED Indicators
System
LED Color Function
P1 Green Lights to indicate power 1 has power.
P2 Green Lights to indicate power 2 has power.
Per 802.3at PoE+ 10/100/1000BASE-T Interface (Port
1 to Port 4)
LED Color Function
LNK/
ACT Green
Lights to indicate the link through
that port is successfully established at
10/100/1000Mbps.
Blinks to indicate that the Switch is
actively sending or receiving data over that
port.
PoE-
in-Use Amber
Lights to indicate the port is providing DC
in-line power.
O to indicate the connected device is not
a PoE powered device (PD).
Per 10/100/1000BASE-T Interface (Port 5)
LED Color Function
LNK/
ACT Green
Lights to indicate the port is successfully
established at 10/100/1000Mbps.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
1. The DC power input range is 48V
~ 54V DC. Please insert
positive and negative DC power wires into contacts 1 and 2
for POWER 1, or 3 and 4 for POWER 2.
DC Input Range:
48-54V
, 3A max.
V1+ V2+
PWR1 PWR2
1 2 3 4
Figure 3-3: Industrial PoE+ Switch DC Input
DC Input Max. PoE Budget
48V~51V 60 watts
52V~54V 120 watts
Note
1. To avoid damage, please use the Industrial PoE+
Switch according to its specifications.
2. Please follow the table above for DC input in
relation with maximum PoE budget.


Produkt Specifikationer

Mærke: Planet
Kategori: Ikke kategoriseret
Model: IGS-504PT

Har du brug for hjælp?

Hvis du har brug for hjælp til Planet IGS-504PT stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Planet Manualer

Planet

Planet IFGS-1222TF Manual

7 December 2024
Planet

Planet IFGS-620TF Manual

8 Oktober 2024
Planet

Planet MTB-LB20 Manual

30 September 2024
Planet

Planet MFB-TFA40 Manual

27 September 2024
Planet

Planet MFB-F60 Manual

21 September 2024
Planet

Planet LS100-SMK Manual

6 September 2024
Planet

Planet IGS-1000-4UP2X Manual

6 September 2024
Planet

Planet NMS-AIoT Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024