Planet ISW-504PT Manual


Læs nedenfor 📖 manual på dansk for Planet ISW-504PT (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 5-Port Industrial Ethernet
Switch with 4-Port PoE, ISW-504PT/ISW-514PTF. The interfaces
of these models are shown below:
Model Name 10/100Mbps RJ45
Ports 100FX SFP Slots PoE Ports
ISW-504PT 5 - 4
ISW-514PTF 4 1 4
In the following section, the term Industrial PoE+ Switch”
means the ISW-504PT/ISW-514PTF.
2. Hardware Introduction
2.1 Switch Front Panel
P1 P2 Fault
120W
PoE Usage
90W
60W
30W
4
5
3
2
1
LNK ACT
PoE-in-Use
挖孔
挖孔
10/100TX
LNK/
ACT
5
DIP
1~4
VLAN
ON
Extended
OFF
Standard
Standard
1234 5
ONDIP
3
1
4
5
3
2
1
LNK ACT
PoE-in-Use
挖孔
P1 P2 Fault
100FX
5
DIP
1~4
VLAN
ON
Extended
OFF
Standard
Standard
120W
PoE Usage
90W
60W
30W
1234 5
ONDIP
2
Figure 2-1:
ISW-504PT front panel
Figure 2-2:
ISW-514PTF front panel
1. Fast Ethernet TP Interfaces
10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters.
2.3 Switch Upper Panel
The upper panel of the Industrial PoE+ Switch consists of one
terminal block connector within two DC power inputs.
Figure 2-3 shows the upper panel of the Industrial PoE+ Switch.
Input DC 12~48V
Fault max.
load 1A@24V
FaultDC1 DC2
1 2 3 4 5 6
Figure 2-3: Industrial PoE+ Switch Upper Panel
2.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of
Industrial PoE+ Switch is used for two DC redundant power
inputs. Please follow the steps below to insert the power wire.
When performing any of the procedures like
inserting the wires or tightening the wire-clamp
screws, make sure the power is OFF to prevent
from getting an electric shock.
2.2 LED Indicators
System
LED Color Function
P1 Green Lights: indicates power 1 has power.
P2 Green Lights: indicates power 2 has power.
FAULT Red Lights: indicates either power 1 or power 2
has no power.
30W Amber
O: indicates the PoE usage is less than
14W.
Blinks: indicates that the PoE usage is
around 15W to 29W.
Lights: indicates the PoE usage is around/
over 30W.
60W Amber
Blinks: indicates that the PoE usage is
around 45W to 59W.
Lights: indicates the PoE usage is around/
over 60W.
90W Amber
Blinks: indicates that the PoE usage is
around 75W to 89W.
Lights: indicates the PoE usage is around/
over 90W.
120W Amber
Blinks: indicates that the PoE usage is
around 100W to 119W.
Lights: indicates the PoE usage is at the
maximum.
Open the box of the Industrial PoE+ Switch and carefully
unpack it. The box should contain the following items:
Industrial PoE+ Switch x 1 Users Manual x 1
Dust Cap x 5 Wall-mount Kit x 1
If any of these are missing or damaged, please contact your
dealer immediately.
2. 100BASE-FX SFP Slot (ISW-514PTF)
100BASE-FX mini-GBIC slot, SFP (small form-factor plug-
gable) transceiver module: From 2 kilometers (multi-mode
ber) to 20/40/60 kilometers (single-mode ber).
3. DIP Switch
The Industrial PoE+ Switch provides one DIP switch for
Standard, VLAN and Extended mode selections. The
detailed descriptions are shown in the following table.
DIP Switch
Mode Function
Standard Switches 1 to 5 are o.
This mode makes the Industrial PoE+ Switch
operate as a general switch and all PoE ports
operate at 10/100Mbps auto-negotiation.
VLAN
Switch 5 is on.
This mode makes the Industrial PoE+ Switch
operate as a V andLAN isolation switch
1. Ports 1 to 4 will isolate respectively.
2. Ports 1 to 4 can only communicate with Port 5.
Note
After adjusting VLAN DIP switch,
reboot the Industrial PoE+ Switch to
make the change take effect.
Extended Any of switches 1 to 4 is on.
This mode makes the Industrial PoE+ Switch
operate on a per-port basis at 10Mbps full duplex
operation but can support IEEE 802.3af PoE power
output over a distance of up to 250 meters
overcoming the 100m limit on Ethernet UTP cable.
Per 802.3at PoE+ 10/100BASE-TX Interface (Port 1
to Port 4)
LED Color Function
LNK/
ACT Green
Lights: indicates the link through that port
is successfully established at 10Mbps or
100Mbps.
Blinking: indicates that the switch is
actively sending or receiving data over that
port.
PoE-
in-Use Amber
Lights: indicates the port is providing DC
in-line power.
O: indicates the connected device is not a
PoE powered device (PD).
Per 10/100BASE-TX Interface (Port 5 of ISW-504PT)
LED Color Function
LNK/
ACT Green
Lights: indicates the link through that port is
successfully established at 10/100Mbps.
Blinking: indicates that the switch is actively
sending or receiving data over that port.
Per 100FX SFP Slot (Port 5 of ISW-514PTF)
LED Color Function
LNK/
ACT Green
Lights: indicates the link through that port is
successfully established at 100Mbps.
Blinks: indicates that the switch is actively
sending or receiving data over that port.
1. The DC power input range is . Please insert 12V ~ 48V DC
positive and negative DC power wires into contacts 1 and 2
for POWER 1, or 5 and 6 for POWER 2.
Input DC 12~48V
Fault max.
load 1A@24V
FaultDC1 DC2
1 2 3 4 5 6
DC Input Max. PoE Budget
12V 60W
24V 90W
48V 120W
Note
To avoid damage, please use the Industrial PoE+
Switch under its specification.


Produkt Specifikationer

Mærke: Planet
Kategori: Ikke kategoriseret
Model: ISW-504PT

Har du brug for hjælp?

Hvis du har brug for hjælp til Planet ISW-504PT stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Planet Manualer

Planet

Planet IFGS-1222TF Manual

7 December 2024
Planet

Planet IFGS-620TF Manual

8 Oktober 2024
Planet

Planet MTB-LB20 Manual

30 September 2024
Planet

Planet MFB-TFA40 Manual

27 September 2024
Planet

Planet MFB-F60 Manual

21 September 2024
Planet

Planet LS100-SMK Manual

6 September 2024
Planet

Planet IGS-1000-4UP2X Manual

6 September 2024
Planet

Planet NMS-AIoT Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024