Planet WGS-803 Manual

Planet Skifte WGS-803

Læs nedenfor 📖 manual på dansk for Planet WGS-803 (4 sider) i kategorien Skifte. Denne guide var nyttig for 26 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET 8-Port 10/100/1000T

Wall-mounted Gigabit Ethernet Switch, WGS-803.

Open the box of the WGS-803 Gigabit Ethernet Switch

and carefully unpack it. The box should contain the

following items:

zThe WGS-803 Gigabit Ethernet Switch x 1

zUser Manual x 1

zDIN-rail Kit x 1

zWall-mounted Kit x 1

zMagnet Kit x 1

z3-pin Terminal Block Connector x 1

zRJ45 Dust-proof Cap x 8

If any item is found missing or damaged, please contact

your local reseller for replacement.

2.1 Terminal Block Connector Pinouts

To install the 3-pin Terminal Block Connector on the

WGS-803, simply follow the following steps:

Step 1: Insert positive DC power wire into V+,

negative DC power wire into , and grounding V-

wire into Ground.

Step 2: Tighten the wire-clamp screws for preventing

the wires from loosening and plug into the

wall-mounted switch.

Note

1. The wire gauge should be in the range

from 12 to 24 AWG

2. The device must be grounded

3. The DC power input range is 12V ~ 48V DC

2.2 LED Indicators

 System

LED Color Function

PWR Green Lights to indicate that the Switch has

power.

2.4 Physical Dimensions (WxDxH):

148 x 24.2 x 134mm

118.00

148.00 24.20

6.00

133.00

134.00

Dimensions ( unit = mm )

2.3 ProductSpecications

Model WGS-803

Hardware Specications

Network

Connector 8-port RJ45 for 10/100/1000BASE-T

MAC Address

Table

8K MAC address table with auto

learning function

Data Buffer 64Kbytes

Switch Fabric 16Gbps

Switch

Throughput 11.9Mpps@64bytes

Flow Control Back pressure for half duplex. IEEE

802.3x pause frame for full duplex

Power

Requirements 12~48V DC, 0.5A (max.)

Power

Consumption 6 watts/20BTU

ESD Protection 6KV DC

EFT Protection 6KV DC

Enclosure IP30 aluminum

2. Hardware Description

The front panel of the WGS-803 Gigabit Ethernet Switch

consists of 8 Auto-sensing 10/100/1000Mbps Ethernet

RJ45 Ports. The LED Indicators are also located on the

RJ45 ports of the Gigabit Ethernet Switch.

10/100/1000BASE-T RJ45 Port

3-pin Terminal Block

DC Plug-in

 10/100/1000BASE-T Interfaces

LED Color Function

LNK/

ACT Green

Lights

To indicate the link through

that port is successfully

established.

Blinks To indicate that the switch is

actively sending or receiving

data over that port.

1000 Green

Lights To indicate that the port is

operating at 1000Mbps.

Off If LNK/ACT LED is lit, it

indicates that the port is

operating at 10/100Mbps.

If LNK/ACT LED is Off, it

indicates that the port is link-

down.

3. Installation

3.1 Wall Mount Installation

To install the WGS-803 Gigabit Ethernet Switch on the

wall, simply follow the following steps:

Step 1: There are 4 holes with 8mm diameter on

the wall; the distance between the 2 holes is

133mm and the line through them must be

horizontal.

Step 2: Install a conductor pipe inside the board hole

and ush the edge of the conductor pipe with

the wall surface.

Step 3: Screw the bolts into the conductor pipe. The

WGS-803 is between bolts and conductor pipe,

as shown below.

Dimensions

(W x D x H) 148 x 24.2 x 134 mm

Weight 498g

Standard Conformance

Standard

Compliance

IEEE 802.3

IEEE 802.3u

IEEE 802.3ab

IEEE 802.3x

Ethernet

Fast Ethernet

Gigabit Ethernet

Flow Control

Regulatory

Compliance FCC Part 15 Class A, CE

Environment

Operating

Temperature: -10 ~ 60 degrees C

Relative Humidity: 5 ~ 95%

(non-condensing)

Storage

Temperature: -20 ~ 70 degrees C

Relative Humidity: 5 ~ 95%

(non-condensing)

Produkt Specifikationer

Mærke:	Planet
Kategori:	Skifte
Model:	WGS-803
Kode for international beskyttelse (IP):	IP30
Bredde:	148 mm
Dybde:	24.2 mm
Højde:	134 mm
Vægt:	498 g
Brugervejledning:	Ja
Produktfarve:	Sort
Opbevaringstemperatur (T-T):	-20 - 70 °C
Relativ luftfugtighed ved drift (H-H):	5 - 95 %
Relativ luftfugtighed ved opbevaring (H-H):	5 - 95 %
Strømforbrug (typisk):	6 W
Driftstemperatur (T-T):	-10 - 60 °C
Husmateriale:	Metal
Certificering:	FCC, CE
Netværksstandarder:	IEEE 802.3,IEEE 802.3ab,IEEE 802.3u,IEEE 802.3x
LED-indikatorer:	Ja
Kan monteres på væggen:	Ja
Harmoniseret systemkode (HS):	85176990
Indgangsstrøm:	0.5 A
Fuld duplex:	Ja
Strøm over Ethernet (PoE):	Ingen
Switch-type:	Ikke administreret
Switch lag:	L2
10G understøttelse:	Ingen
Flowkontrol support:	Ja
Kobber ethernet kabelteknologi:	10BASE-T,100BASE-TX,1000BASE-T
Basis omskiftning RJ-45 Ethernet porte, antal:	8
Basis omskiftning RJ-45 Ethernet porttype:	Gigabit Ethernet (10/100/1000)
Opbevar-og-frem:	Ja
MAC adresselabel:	8000 entries
Switch kapacitet:	16 Gbit/sek.
Gennnemløb:	11.9 Mpps
Jumbo Frames support:	Ja
Jumbo rammer:	9216
Stativ-montering:	Ingen
Varmeafgivelse:	20 BUT/t
Gigabit Ethernet (kobber) porte, antal:	8
MAC-adresse auto-indlæring understøttet:	Ja
MAC-adresse auto-forældelse understøttet:	Ja
DIN-skinne montering:	Ja
Monteringssæt til væggen:	Ja