Pyle PHRM76 Manual
Læs nedenfor 📖 manual på dansk for Pyle PHRM76 (1 sider) i kategorien Sportsur. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/1
PERSONAL TRAINER
Thank you for choosing Pyle as your personal trainer. We want you to make the
most out of your new gadget, so please read the instruction manual carefully, and
keep the manual for future reference.
Important:
Please note that the watch is NOT a medical device and is not to be used as such.
The PHRM76 requires two CR2032 lithium batteries, one for the watch and one for
the heart rate belt. Only the recommended batteries are to be used.
When replacing the batteries, the following are to be strictly observed.
1. Only the recommended batteries are to be used.
2. Only adults should install and replace the batteries.
3. DO NOT use rechargeable batteries, and DO NOT recharge non-
rechargeable batteries.
INSTALLING THE BATTERY
Note:
1. The battery compartments are located at the back of the watch.
2. To install or replace the battery, unscrew the back cover carefully.
3. Take out the old batteries and dispose responsibly.
4. Gently place a new battery into the battery slot of the battery compartment,
making sure that the poles are correctly placed, and screw the back cover on.
3D SENSOR FROM USA - MEASURES YOUR MOVEMENT ACCURATELY
The 3D technology used is an accelerometer sensor that detects and measures
acceleration in walking or running. It has an intelligent step filter function, meaning
it only counts steps when 15 steps have been detected. In addition, you can
customize specific personal setting for your walking or running motion.
CONTENTS
Getting Started .................................................................................................
Installing the Battery .........................................................................................
Using the watch function ..................................................................................
Symbol on LCD ................................................................................................
Mode Flow Chart ..............................................................................................
Set the Time & Date .........................................................................................
Alarm Mode ......................................................................................................
Setting the Alarm ..............................................................................................
Chronograph Mode ..........................................................................................
Start the Chrono ...............................................................................................
Set the Target ...................................................................................................
Data Record .....................................................................................................
Calibration ........................................................................................................
Setting the Calibration ......................................................................................
User Setting Mode …………………………………………………………..……...
Specification………………………………………………………………….………
Caution………………………………………………………………………………..
USING THE WATCH FUNCTIONS
IMPORTANT!
• Prior to your purchase of the watch, the watch is switched off for energy saving
purposes, and you can turn it on by pressing the MODE key.
• For energy saving purposes, the watch unit will switch off automatically at
midnight (00.00/12.00am) every night. Press the MODE key to turn it on.
WALKING AND RUNNING MODE
- There are two-step counting features, one is for the walking mode and the other
is running mode. For each mode, calibration of stride length is required for both.
• There maybe a delay between the start of your walk and the counting of steps.
yThis intelligent filter acts to maximize accurac , and exclude movements outside
of a normal walking motion. Once the watch has recognized your walking activity,
it will take into account the initial steps taken during the delay.
NOTE
• If the watch is inactive for longer than 1 minute in any modes, the main screen
will automatically return to time mode.
2 3
SCREW
BACKCOVER
ORing
CR2032
BATTERY
- If you wish to have the most accurate fitness index calculated by the unit, the
user must use the calibration feature for both walking and running. They will also
need to input their personal user settings.
In order to maximize the accuracy of the step counting feature of the watch, please wear
the watch as shown in the diagram (straps of the watch must be fastened tightly around
the wrist; display must also be perpendicular to the forearm and wrist; the watch must
only be worn on the left wrist and not the right to maximize the accuracy of step counting)
as the design and accuracy of the watch for step counting is based on the positioning of
the watch.
You will notice that there are two noticeably different patches on the inside of the heart
rate belt. These are the sensors for detecting your heart rate. Before you put on the
heart rate belt, wet these two patches lightly so that the sensors can detect your heart
rate more easily, faster and more accurately.
• User Setting
• EL Backlight
• Low Battery Detection
• Key tone
• Energy Saving Function
• Memory Data Recall
MODE FLOW
TIME → ALARM → CHRONO → DATA RECALL A → CALIBR TION → USER
SETTING → TIME
10. Press or hold either the START/STOP/+ button to increment the month’s digits
or NEXT/SAVE/- button to decrement the number.
11. Press MODE button to set the year.
12. Press or hold either the START/STOP/+ button to increment the year’s digits or
NEXT/SAVE/- button to decrement the number.
13. Press MODE key to confirm, and choose either the 12-hour or 24-hour format
for the time by pressing the START/STOP/+ or NEXT/SAVE/- button to toggle
between the two options.
To save and exit setting mode, hold the MODE button for 3 seconds or alternatively,
one minute of inactivity will trigger the watch to return to the default TIME mode
Note : At anytime, to exit the time and date setting mode, hold the MODE button for 3
seconds and all revised changes will be saved.
ALARM MODE
1. Press the MODE button to scroll through the features until
you locate the alarm mode, displaying “ALARM”.
2. To turn the alarm on or off, press the START/STOP/+ or
NEXT/SAVE/- button to toggle between the two options.
Note:
- If the watch is inactive for longer than 1 minute in any modes, the main screen will
automatically return to time mode.
SETTING THE ALARM
1. Hold the MODE button for 3 seconds to set the alarm, and the minutes’ digits
should flash.
2. Press or hold either the START/STOP/+ button to increment the minutes’ digits or
NEXT/SAVE/- button to decrement the number.
3. Press MODE button to set the hour.
4. Press or hold either the START/STOP/+ button to increment the hours’ digits or
NEXT/SAVE/- button to decrement the number.
5. To save and exit setting mode, hold the MODE button for 3 seconds or alternatively,
one minute of inactivity will trigger the watch to return to the default TIME mode.
Note:
- Any changes made in the alarm mode will automatically
enable the alarm.
- If the watch is inactive for longer than 1 minute in any modes,
the main screen will automatically return to time mode.
CHRONOGRAPH MODE
1. Press the MODE button to scroll through the features
until you locate the chronograph mode.
2. Press the NEXT/SAVE/- button to select OFF, WALK or RUN.
4567
SYMBOL ON LCD
- Chime
KM - Kilometers
gFAT - Unit of Fat Burnt
KM/h - Kilometers per hour
STEP - Step you have walked or ran
Kcal - Unit of Calories Burnt
- Key Tone
RUN - Run mode
WALK - Walk mode
AM - Time from 0:00.00 to 11:59.59
PM - Time from12:00.00 to 23:59.59
- Alarm
Exercise equipment with electronic components may interfere signals and heart
rate belt transmission. To tackle these problems, try the following:
1. Remove the transmitter from your chest and use the exercise equipment as you
would normally.
2. Move the wrist unit around until there is a consistent transmission signal between
the unit and the heart rate belt, and avoid placing it near the display panel of
electrical equipment as there is greater interference.
In order to maximize the accuracy of the heart rate monitor, please wear the heart rate
belt on your chest with the sensor over your heart for detection of the heart rate.
This unit is operated by four keys:
• MODE / SET
• NEXT / SAVE / -
• STA / STOP /+RT
• RESET / EL
FEATURES:
• Time & Date
• Daily Alarm
• Current / Average / Max / Min Heart Rate
• Target Heart Rate Zone Setting ( Highest & Lowest heart rate alert alarm )
• Chronograph with 15 Memory Records
• Dual Purpose 3D sensor (Walking or Running)
• Intelligent step filter function
• Target Distance Alert Alarm
• Target Time Alert Alarm
• Current / Average / Max / Min Speed
• Total Distance
• Calibration Function
• Total Calorie Burnt
• Total Fat Burnt
Electromagnetic disturbances may occur near high-voltage power lines, traffic lights,
overhead lines of electric railways, electric bus lines or trams, televisions, car motors,
bike computers, some motor driven exercise equipment, cellular phones, or at electric
security gates. To avoid erratic readings, move away from possible sources of
disturbance.
SETTING THE TIME AND DATE
1. Press the MODE button to scroll through the features until
you locate the time mode, which displays the time and date.
2. Hold the MODE key for 3 seconds to enter the TIME SETTING
MODE and the seconds’ digits should flash.
3. Press MODE to set the minutes.
4. Press or hold either the START/STOP/+ button to increment the
minutes’ digits or NEXT/SAVE/- button to decrement the number.
5. Press MODE button to set the hour.
6. Press or hold either the START/STOP/+ button to increment the hours’ digits or
NEXT/SAVE/- button to decrement the number.
7. Press MODE button to set the date.
8. Press or hold either the START/STOP/+ button to increment the date’s digits or
NEXT/SAVE/- button to decrement the number.
9. Press MODE button to set the month.
Maximum heart rate range : 80 – 220 BPM
Minimum heart rate range : 30 – 150 BPM
Target Speed for Walking
1. Press the START/STOP/+ or NEXT/SAVE/- button to turn the Target Speed for
walking ON or OFF.
2. Press the MODE button to set the Maximum speed for walking.
3. Press or hold either the START/STOP/+ button to increment the maximum speed
or NEXT/SAVE/- button to decrement the number.
4. Press the MODE button to set the Minimum Speed for walking.
5. Press or hold either the START/STOP/+ button to increment the maximum speed
or NEXT/SAVE/- button to decrement the number.
6. Maximum speed for walking range : 3-8 km/h.
7. Minimum speed for walking range : 1-3 km/h.
Target Speed for Running
1. Press START/STOP/+ or NEXT/SAVE/- button to the Target Speed for running ON
and OFF.
2. Press the MODE button to set the Maximum Speed for running.
3. Press or hold either the START/STOP/+ button to increment the maximum speed
or NEXT/SAVE/- button to decrement the number.
4. Press MODE button to set the Minimum Speed for running.
5. Press or hold either the START/STOP/+ button to increment the minimum speed or
NEXT/SAVE/- button to decrement the number.
6. Max speed for running range : 5-30 km/h.
7. Minimum speed for running range : 3-29 km/h.
Hold the MODE button 3 seconds to confirm the setting and back to CHRONO mode
Note:
• Any changes on the Target distance will automatically enable Target distance
function.
• Any changes on the Target heart rate setting will automatically enable the Target
heart rate Alert Alarm function.
• Any changes on Target Speed of walking & running setting will enable the Target
Speed Alert Alarm function automatically.
• If the watch is inactive for longer than 1 minute in any modes, it will automatically
return to chronograph mode, and all changes will be saved.
• Hold the MODE button for 3 seconds anytime will exit the setting mode and all
revised setting will be saved.
• 3 beeps x 3 times alert alarm when target time reach
• 4 beeps x 3 times alert alarm when target distance reach
• 2 beeps per 10 seconds when heart rate is higher than Max heart rate setting
3. Hold the NEXT/SAVE/- button for 3 seconds to activate the Heart Rate Monitor.
4. Press the START/STOP/+ button to start the chronograph, and the device will start
to count the steps and measure your heart rate.
Note:
- If the watch is inactive for longer than 1 minute in any modes, the main screen will
automatically return to time mode.
START THE CHRONOGRAPH
1. Press the START/STOP/+ button to start the chronograph.
2. During the exercise session, you can scroll through the data being measured:
Current Speed/Current Heart Rate, Distance/Current Heart Rate, Steps/Average
Heart Rate, Calories/Maximum Heart Rate and Fat Burnt/Minimum Heart Rate by
pressing the NEXT/SAVE/- button.
3. Press the START/STOP/+ button to stop the chronograph and press again to
re-start the chronograph.
4. Hold the NEXT/SAVE/- button for 3 seconds to save the record when the
chronograph has been stopped.
5. Press the START/STOP/+ or NEXT/SAVE/- button to select YES or NO.
6. Hold the NEXT/SAVE/- button for 3 seconds to save the data record, and return to
the chronograph mode.
Note:
- When the pedometer function is off, ONLY the heart rate information can be viewed.
- When the heart rate function is off, ONLY the pedometer information can be viewed.
- When chronograph has started, you can view the current time ( Time Mode ) by
pressing the Mode button, and the screen will automatically revert back to
chronograph after 10 seconds.
- If the watch is inactive for longer than 1 minute in any modes, the main screen will
automatically return to time mode.
SET YOUR TARGET
1. Press the MODE button to scroll through the features until you locate the
chronograph mode.
2. Hold the MODE button for 3 seconds to set the target.
3. Press the MODE button again to select :
• Target Time (Timer)
• Target Distance
• Target Heart Rate Setting (Maximum & Minimum Heart Rate )
• Target Speed Setting for walking (Maximum & Minimum Speed )
• Target Speed Setting for running ( Maximum & Minimum Speed )
The chronograph must be reset to 0 before the setting mode can be accessed.
Target Time (Timer) – Range : 00:00:01 – 23:23:59
1. Press the START/STOP/+ or NEXT/SAVE/- button to turn the Target Time feature
ON or OFF.
2. Press MODE button to enter the Target Time setting.
3. Press or hold either the START/STOP/+ button to increment the value or NEXT/
SAVE/- button to decrement the number.
4. Press the MODE button to select the value setting (second → minute → hour )
Target Distance – Range : 100M to 20Km
1. Press the START/STOP/+ or NEXT/SAVE/- button to turn the Target Distance
feature ON or OFF.
2. Press the MODE button to set the Target Distance.
3. Press or hold either the START/STOP/+ button to increment the distance or NEXT/
SAVE/- button to decrement the distance.
Target Heart Rate
1. Press the START/STOP/+ or NEXT/SAVE/- button to turn the Target Heart Rate
feature ON or OFF.
2. Press the MODE button to set the Maximum Heart Rate.
3. Press or hold either the START/STOP/+ button to increment the maximum heart
rate or NEXT/SAVE/- button to decrement the number.
4. Press MODE button to set the Minimum Heart Rate
5. Press or hold either the START/STOP/+ button to increment the minimum heart rate
or NEXT/SAVE/- button to decrement the number.
8910 11
• 1 beep per 10 seconds when heart rate is lower than Min heart rate setting.
• 3 beeps per 10 seconds when Speed is higher than Max speed setting
• 1 beep per 10 seconds when Speed is lower than Min speed rate setting.
D A RECORD AT
1. Press the MODE key until you have reached the DATA RECORD mode.
2. Hold the MODE button for 3 seconds to select record and the record number
should start flashing.
3. Press START/STOP/+ button or NEXT/SAVE/- button to scroll through the
numbered records.
4. Press the MODE button again to confirm the record.
5. Press START/STOP/+ button or NEXT/SAVE/- button to view the below data:
i. Record Date / Record Time / Record No.
ii. Chrono Time / Avg Speed / Avg Heart Rate ;
iii. Total Distance / Total Step / Max Heart Rate ;
iv. Total Fat Burnt / Total Calories Burnt / Min Heart Rate ;
Delete Record:
1. Hold the NEXT/SAVE/- button for 3 seconds to select the record
to be deleted, and then hold the MODE button for 3 seconds to delete the record.
2. Hold the NEXT/SAVE/- button for 4 seconds to delete all records, and then hold
MODE button for 3 seconds to delete.
3. Press MODE button will back to the record selection mode
Note:
Every time the watch is reset, all records will be removed. No buttons pressed or held
for 60 seconds will automatically trigger the watch to return to time/date Mode.
CALIBRATION
1. Press the MODE button to scroll through the features until you locate the
calibration feature, displaying “CAL”.
2. Press the NEXT/SAVE/- button to select “WALK” or “RUN”.
3. Press the START/STOP/+ button to start the calibration, and press again to stop
the calibration.
4. To save and exit the calibration feature, hold the MODE button for 3 seconds or
alternatively, one minute of inactivity will trigger the watch to return to the default
TIME mode.
Setting the Calibration
1. Hold the MODE button for 3 seconds to enter the Calibration Setting Mode.
2. Increment or decrement the Calibration Distance by pressing or holding the
START/STOP/+ or NEXT/SAVE/- button.
3. Confirm the Calibration Distance by holding the MODE button for 3 seconds,
which should trigger the watch to return to calibration mode. If the watch is
inactive for longer than 1 minute in any modes, the main screen will automatically
return to time mode.
Note:
- Stride length is limited to a range of 20-180cm (8” to 5’11”) for both walking and
running. If the calibrated result is beyond this range then the previous stride length
will be used.
- If stride calibration has not been performed before, the stride value will be set based
on the height. But once the stride has been calibrated, this will automatically replace
the stride length calculated based on the user’s height
- Calibration is not available when Chronograph is running..
- Default : 400M, Range : 100m to 10Km
- Selection : From 100m to 1Km, 100m spacing. From 1Km to 10Km, 1Km spacing
USER SETTING
1. Press the MODE button to scroll through the features until
you locate the user setting mode, displaying “USER”.
2. Hold the MODE button for 3 seconds to enter User Setting
Mode – UNIT
3. Press the START/STOP/+ or NEXT/SAVE/- button to change
the units (imperial or metric).
4. Press the MODE button to enter next setting – WEIGHT
5. Press START/STOP/+ or NEXT/SAVE/- button to increment
or decrement the weight. (Default:45kg/99lb, Range:20-227kg/45-501lbs)
6. Press the MODE button to enter next setting – HEIGHT
7. Press the START/STOP/+ or NEXT/SAVE/- button to increment or decrement the
height. (Default:170cm/5’6”, Range:50-250cm/1’8”-8’2”)
8. Press the MODE button to enter next setting – AGE
9. Press the START/STOP/+ or NEXT/SAVE/- button to increment or decrement the
age. (Default:26, Range:5-128)
SPECIFICATIONS
Time Format: Year, month, date, day, hour, minute, second, am/pm
12/24 hours
Calendar System: Full Auto-calendar pre-programmed from 2000 to 2099
Features: Current / Average Speed, Step Counting, Calories
Consumption, Fat Burnt, Exercise time
Measurement Range: Calories Consumption: 0-9999.99 kcal
Fat Burnt: 0-9999.99
Number of step: 0-999999
Distance:0-9999.99 km
Time: 0-23 hr 59 m 59 s 99Exercise
Memory Data: 15 Memory Record
Chronograph: Measuring Unit: 1/100 second
Measuring Capacity: 23 hr 59 m 59 s 99
CAUTION
Should you encounter any problems with the watch (e.g. malfunctioning of a
parameter, static electricity, interferences within the product or the need to re-set
the device), please press four buttons at the same time to reset the watch (the
watch should not connect with computer). All data previously input into the device
will be erased and you can then/will need to re-set the watch all over again. Should
this fail to correct the situation, remove the batteries and then put them back into
the battery compartment.
Then follow all the steps mentioned above in order to input the necessary data
once more. The content of this manual is subject in order to change without further
notice. Due to printing limitation, the displays shown in this manual may differ from
the actual display. The manufacturer and its suppliers hold no responsibility to you
or any other persons for any damage expenses, lost-profits, or any other claims
arisen by using this product. The contents of this manual may not be reproduced
without the permission of the manufacturer.
12 13
10. Press the MODE button to enter next setting – GENDER
11. Press START/STOP/+ or NEXT/SAVE/- button to toggle between Male or Female.
(Default:Male)
12. Press the MODE button to enter next setting – WALKING STRIDE LENGTH
13. Press the START/STOP/+ or NEXT/SAVE/- button to increment or decrement the
setting data. (Default:71cm/27”, Range:20-180cm/8”-70”)
14. Press the MODE button to enter next setting – RUNNING STRIDE LENGTH
15. Press the START/STOP/+ or NEXT/SAVE/- button to increment or decrement the
setting data. (Default:120cm/47”, Range:20-180cm/8”-70”)
16. Press the MODE button to enter next setting – KEY TONE (BEEP)
17. Press START/STOP/+ or NEXT/SAVE/- button to select ON or OFF. (Default: OFF)
18. Press the MODE button to enter next setting – CHIME
19. Press START/STOP/+ or NEXT/SAVE/- button to select ON or OFF. (Default: OFF)
20. If the watch is inactive for 60 seconds and the unit will return to User Setting Mode.
If no buttons are pressed for a further 60 seconds, the watch will bring the time/date
mode back.
14
73-271-0001
2
2
3
5
6
6
7
7
7
8
9
11
11
12
12
14
14
PyleAudio.com
Model: PHRM76
Produkt Specifikationer
| Mærke: | Pyle |
| Kategori: | Sportsur |
| Model: | PHRM76 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Pyle PHRM76 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Sportsur Pyle Manualer
29 September 2024
19 September 2024
13 August 2024
13 August 2024
6 August 2024
6 August 2024
6 August 2024
5 August 2024
2 August 2024
2 August 2024
Sportsur Manualer
- Sportsur Denver
- Sportsur Suunto
- Sportsur Beurer
- Sportsur Medisana
- Sportsur Apple
- Sportsur Epson
- Sportsur Amazfit
- Sportsur TFA
- Sportsur Garmin
- Sportsur Motorola
- Sportsur Polar
- Sportsur Casio
- Sportsur Trevi
- Sportsur Crivit
- Sportsur Silva
- Sportsur Medion
- Sportsur Soehnle
- Sportsur Huawei
- Sportsur Ventus
- Sportsur Sigma
- Sportsur Krontaler
- Sportsur Bryton
- Sportsur CicloSport
- Sportsur Echowell
- Sportsur Xiaomi
- Sportsur Mondaine
- Sportsur Timex
- Sportsur Fossil
- Sportsur NGM
- Sportsur Adidas
- Sportsur TomTom
- Sportsur Honor
- Sportsur Fitbit
- Sportsur Wahoo Fitness
- Sportsur ADE
- Sportsur Prixton
- Sportsur SPC
- Sportsur Lezyne
- Sportsur Misfit
- Sportsur Evolveo
- Sportsur Runtastic
- Sportsur Umidigi
- Sportsur Oregon Scientific
- Sportsur Scosche
- Sportsur Ciclo
- Sportsur Sportline
- Sportsur Goodis
- Sportsur ACME
- Sportsur Cresta
- Sportsur Brigmton
- Sportsur Sunstech
- Sportsur Kubo
- Sportsur Naxa
- Sportsur Ematic
- Sportsur Ticwatch
- Sportsur Billow
- Sportsur Guardo
- Sportsur Crane
- Sportsur Coros
- Sportsur Kikos
- Sportsur Swami
- Sportsur Cubot
- Sportsur Fen
- Sportsur IZZO Golf
- Sportsur Bitween
- Sportsur Prologue
- Sportsur Soleus
- Sportsur Ronstan
Nyeste Sportsur Manualer
10 Oktober 2024
7 Oktober 2024
5 Oktober 2024
4 Oktober 2024
21 September 2024
20 September 2024
13 September 2024
12 September 2024
8 September 2024
6 September 2024