Pyle PLMTR4A Manual

Pyle Modtager PLMTR4A

Læs nedenfor 📖 manual på dansk for Pyle PLMTR4A (4 sider) i kategorien Modtager. Denne guide var nyttig for 23 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

4-Ch. Waterproof Rated Amplifier

Marine Grade PowerSport Amp for ATV,

UTV, 4x4, Jeep (1500 Watt)

PLMTR4A

P l USA P l USA P l USA

INTRODUCTION

This power amplier has been designed to provide high quality performance with a minimum of maintenance.

However, it's performance will only be as good as the care and quality of components with which is installed.

We therefore advise that you read these instructions very carefully to familiarize yourself with the product and

it's features. Before installing the power amplier please read this instruction manual carefully. The instructions

for mounting and connecting the set have to be followed precisely. If nec essary, a service center should be

consulted. All connections for DC power, signal input and speaker outputs can be carried out easily and safely

by way of RCA and screwed terminals.

INSTALLATION INSTRUCTIONS

Please choose a mounting place without any direct weather inuences. Note that the amplier generates heat

so that a well ventilated place is necessary. According to your vehicle's and marine boat's construction the set

can be made very carefully in order to ensure the amplier's full performance and reliability.

Keep the wire connections as short as possible with sucient dimensions in order to minimize power losses

and provide a higher audio output of the system. For safety reasons route all power and speaker wiring by

using the exiting wire channels. To minim ize damage to the cables, take care that they do not pass sharp

edged metal. Lay all cables as far away as possible from the ignition cables, modules in the boot and under the

key dashboard, as this create interference. Add a fuse into the (+) power cable in a distance of not more than 30

cm from the positive battery pole. Keep the length of the power wires as short as possible. It is better to use

power cables which are short and then longer speaker cables. In order to reduce interference, also pay

attention to the instructions.

PRECAUTIONS

• This unit is designed for negative ground 12-14.50 Volts (DC) operation only.

• Use speakers with an impedance of 4 Ohms

• Avoid installing the unit where:

• It would be subject to high temperatures, such as from direct sunlight or hot air from the heater.

• It would be exposed to rain or moisture.

1 2 3

• It would be subject to dust or dirt.

• If your vehicle or boat is parked in direct sunlight and there is a considerable rise in temperature inside the

car, allow the unit to cool o before operation.

• When installing the unit horizontally, be sure not to cover the heatsink ns with the oor carpet. • If this unit is placed too close to the resources radio, an interference may occur. In this case, separate the

amplier from the car radio. • This power amplier employs a protection circuit to protect the transistors and speakers if the amplier

malfunctions. Do not attempt to test the protection circuits by covering the heatsink or connecting improper

loads. • Do not use the unit with a weak auto battery as its optimum performance depends on a normal battery

supply voltage.

• For safety reasons, keep the volume of your audio system moderate so that you can still hear normal trac

sounds in a reasonable distance.

WIRING INSTRUCTIONS

POWER CONNECTION

• The battery terminal (BATT) must be connected directly to the positive terminal of the vehicle battery to

provide an adequate voltage source and minimize noise. Connecting the battery terminal lead to any other

point (such as the fuse block) will reduce the power output and may cause noise and distortion. Use only #12

gauge or thicker (smaller gauge #) wire for this lead and connect it to the terminal of the battery after all other

wiring is completed.

GROUND CONNECTION

• The ground terminal (GND) connection is also critical to the correct operation of the amplier. Use a wire of

the same gauge as the power connection (#8 or thicker) and connect it between the ground terminal(GND) of

the amplier and a metal part of the vehicle close to the mounting location. This wire should be as short as

possible and any paint or rust at the grounding point should be scraped away to provide a clean metal

surface to which the end of the ground wire can be screwed or bolted.

REMOTE TURN-ON CONNECTION

• The amplier is turned on by applying +12V to the remote turn-on terminal (REM). The wire lead to this

terminal should be connected to the "Auto-Antenna" lead from the vehicle/or boat stereo resources which

will provide the +12V only when the stereo resources is turned on . If the car stereo does not provide an

"Auto-Antenna" lead, the remote turn-on lead may be wired to an "Accessory" or "Radio" terminal in the

vehicle's/or boat's fuse block. This will turn the amplier on and o with the ignition key, regardless of

whether the stereo resources is on or o. The remote turn-on lead does not carry large currents. So #16

gauge wire may be used for this application.

SPEAKER CONNECTIONS

• Depending on the type and number of speakers used with the amplier wire them to the speaker terminals

as per the appropriate wiring diagram. For most applications # 18 gauge wire should be used for the speaker

leads but in no case thinner than # 16 gauge. For leads is excess of 10 feet #12 gauge is recommended. When

wiring the speakers, pay careful attention to the polarity of the terminals on the speakers and make certain

they correspond to the polarity of the corresponding terminals on the amplier. Do not ground any speaker

leads to the chassis of the vehicle/or boat.

Features:

• Pro Audio PowerSport Amplier

• 4-Channel Audio Amp System

• Marine Grade Rugged Construction

• Waterproof Rated & Weather-Resistant Connectors

• Integrated Power Wiring Harness

• Perfect for Custom Installations & Applications

• Ability to Connect & Stream Audio from External Devices

• Wired Mini 3.5mm AUX Audio Input

• Speaker Wiring Connectivity

• Pre-Amp RCA Out to Any OEM /

Factory Made Universal

Mono Block/or Full Range Amplier

• Anti-Thump Turn-On

• Soft Turn On / O

• Overload & Power Protection Circuitry

• Used for Watercraft

& Portable Mobile Vehicle Sound Systems

P l USA

Technical Specs:

• Power Output: 1500 Watt MAX

• MAX Power: 4 x 375 Watt @ 4 Ohm (4 x 190 Watt)

• Marine Grade Waterproof Rating: IP-65

• T.H.D: 0.1%

• S/N Ratio : > 95 dB

• Channel Separation : > 65 dB

OPERATION

After the amplier has been installed and all connections have been made carefully and securely, turn the radio

on so that the amplier is switched on automatically. After a short power-on period, the amplier reaches its

full performance. Now turn up the volume slowly using the volume control of the radio. If there is no sound or

only a distorted replay, switch o the radio immediately - the amplier will also switch o automatically - and

check if all connections have been made correctly.

GND (-) = GROUND CONNECTION

• Connect the GND terminal to the chassis ground of your vehi cle/or boat and take care of best electric and

mechanic contact. In doing so, drill a hole into the vehicle/or boat chassis near the amplier then remove

color, dirt or any other substance from the ground point . Thereafter fasten the cable end with added ring

terminal by using a screw. Ensure that the ground connection is as short as possible and that the cable

diameter is sucient (min 4mm"). Route the ground cables from the radio and all other equipment parts, like

equalizer, active crossover network or other ampliers, to the same ground point.

+ 12V = POWER SUPPLY

• Connect the BATT te rminal to the positive pole of the battery with a lead cable and add a fuse into the power

cable in a distance of not more than 30 cm from the battery. The lead cable's diameter should be at least 4

mm' for a length of 3 m and 6 mm" for a length of 6 m.

REM (ON/OFF) REMOTE CONTROL

• Connect the REM terminal to the automatic antenna connector of your vehicle/or boat radio. Now when

turning on and o your vehicle/or boat radio. the amplier automatically switches ON and OFF.

A cable diameter of 0.5 mm² is sucient.

• Frequency Response : 10 - 40kHz

• Fuse: 10A

• Power: DC 12V

• Amp Dimensions (L x W x H):

5.90’’ x 3.62’’ x 1.97’’ -inches

• Sold as: 1

Produkt Specifikationer

Mærke:	Pyle
Kategori:	Modtager
Model:	PLMTR4A

Har du brug for hjælp?

Hvis du har brug for hjælp til Pyle PLMTR4A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Pyle Manualer

Pyle PTAU45.5 Manual

22 September 2024

Pyle PWMA3003BT Manual

20 September 2024

Pyle Pro PTAU23 Manual

6 September 2024

Pyle INV500DBA Manual

5 September 2024

Pyle PDA4BU Manual

3 September 2024

Pyle PD1000BA Manual

1 September 2024

Pyle Elite UPLMRA430BT Manual

1 September 2024

Pyle PLAM2001D Manual

30 August 2024

Pyle PT1100 Manual

30 August 2024

Pyle PFA100 Manual

30 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Sony STR-DE185 Manual

23 November 2024

Henry Engineering AES DIGITAL DA 2X4 Manual

21 November 2024

QSC PowerLight 9.0 Manual

20 November 2024

Ashly FX-125.4 Manual

20 November 2024

JBL Grand Touring GTO-501EZ Manual

20 November 2024

Harman Kardon CA5250 Manual

19 November 2024

Esoteric F-05 Manual

19 November 2024

Konig & Meyer 28075 Manual

18 November 2024

IFi Audio ZEN CAN 3 Manual

18 November 2024

JBL Marine MA6002 Manual

18 November 2024