Qubino Flush PWM Manual

Qubino Termostat Flush PWM

Læs nedenfor 📖 manual på dansk for Qubino Flush PWM (2 sider) i kategorien Termostat. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Qubino

The INNOVATIVE SMALLESTand

Flush PWM Thermostat

ORDERING CODE

Z-WAVE FREQUENCY

ZMNHLD1

868,4 MHz

ZMNHLD2

921,4 MHz

ZMNHLD3

908,4 MHz

ZMNHLD4

869,0 MHz

ZMNHLD5

916,0 MHz

ZMNHLD8

865,2 MHz

This Z-Wave module is used to regulate temperature.

Regulation is done using full wave PWM technology. The

module can be controlled either through Z-wave network or

through the wall switch.

The module is designed to be mounted inside a ﬂush “

mounting and is hidden behind a traditional wall switch. box”

Module measures power consumption of connected device.

It is designed to act as repeater in order to improve range

and stability of Z-wave network.

Supported switches

Module supports switches (push button) and mono-stable

bi-stable switches. The module is factory set to operate

with -stable switches. bi

Installation

 To prevent electrical shock and/or equipment damage,

disconnect electrical power at the main fuse or circuit

breaker before installation or any servicing.

 Make sure, that no voltage is present in the installation.

 Prevent the disconnecting device from being switched

on accidentally.

 Connect the module according to electrical diagram.

 Locate the antenna far from metal elements (as far as

possible).

 Do not shorten the antenna.

Danger of electrocution!

 Module installation requires a great degree of skill and

may be performed only by a qualiﬁed and licensed

electrician.

 Even when the module is turned oﬀ, voltage may be

present on its terminals. Any works on conﬁguration

changes related to connection mode or load must be

always performed by disconnected power supply (disable

the fuse).

Note!

Do not connect the module to loads exceeding

recommended values. Connect the module only in

accordance to the below diagrams. Improper connections

may be dangerous.

Electrical installation must be protected by directly

associated over current protection fuse 1A, gG or Time

lag T, rated breaking capacity 1500A (ESKA 522.717)

must be used according to wiring diagram to achieve

appropriate overload protection of the module. The

fuse must be installed in fuse holder type: Adels

contact 503 Si / 1 DS

Package contents:

 Flush PWM thermostat + Temperature sensor

Electrical diagram 230VAC

Notes for the diagram:

Neutral lead

Live lead

Output

Input for switch /push button or sensor*

Terminal for digital temperature sensor (only for

Flush PWM thermostat module compatible digital

temperature sensor).

*For details please check parameters 11, 12 and 1 3

Electrical diagram 24VDC

Notes for the diagram:

+ VDC

- VDC

Output

Input for switch /push button or sensor*

Terminal for digital temperature sensor (only for

Flush PWM thermostat module compatible digital

temperature sensor).

*For details please check parameters 11, 12 and 1 3

WARNING: Service button S when must NOT be used

module is connected to 110-230V power supply.

WARNING: the temperature sensors should not be

exposed to water.

Module Inclusion (Adding to Z-wave network)

 Connect module to power supply (with

temperature sensor connected ),

 enable add/remove mode on main controller

 auto-inclusion (works for about 5 seconds after

connected to power supply) or

 press push button I1 three times within 3s (3 times

change switch state within 3 seconds) or

 press service button (only applicable for 24 V SELV S

supply voltage) for more than 2 second.

NOTE 1: For auto-inclusion procedure, ﬁrst set main

controller into inclusion mode and then connect module to

power supply.

NOTE 2: When connecting temperature sensor to module

that has already been included, you have to exclude

module ﬁrst. Switch oﬀ power supply, connect the sensor

and re-include the module.

Module Exclusion/Reset (Removing from

wireless network)

 Connect module to power supply

 bring module within maximum 1 meter (3 feet) of the

main controller,

 enable add/remove mode on main controller

 press push button I1 ﬁve times within 3s (5 times change

switch state within 3 seconds) in the ﬁrst 60 seconds after

the module is connected to the power supply or

 press service button (only applicable for 24 V SELV S

supply voltage) for more than 6 second.

By this function all parameters of the module are set to

default values and own ID is deleted.

If push button I1 is pressed three times within 3s (or service

button S is pressed more than 2 and less than 6 seconds)

module is excluded, but conﬁguration parameters are not

set to default values.

NOTE: If the module is included with parameters 100,101

or 102 with values diﬀerent to default and module reset is

done, wait at least 30s before next inclusion.

Association

Association enables thermostat module to transfer PWM

commands inside Z-Wave network directly (without main

controller) to other Z-Wave modules.

Associated Groups:

Group 1: Lifeline group (reserved for communication with

the main controller), 1 node allowed.

Group 2: basic on/oﬀ (triggered at change of the output Q

state and reﬂecting its state) up to 16 nodes.

Group 3: SENSOR_MULTILEVEL_GET (triggered once per

minute if Parameter 121 is not 0) up to 16 nodes.

Group 4: basic on/oﬀ (triggered by Too high temperature

limit, it send 0x00 in Heating mode and in Cooling 0xFF

mode, trigged by Too low temperature limit, it send 0x00 in

Heating mode and 0xFF in Cooling mode; hysteresis is 1°C)

up to 16 nodes.

Group 5: THERMOSTAT_SETPOINT_G (triggered once ET

per minute if Parameter 121 is not 0) up to 16 nodes.

Group 6: basic on/oﬀ (trigged by change of I1 if window

sensor functionality is selected by parameter no. 11) up to

16 nodes.

Group 7: basic on/oﬀ (trigged by change of I2 if condense

sensor functionality is selected by parameter no. 12) up to

16 nodes.

Group 8: basic on/oﬀ (trigged by change of I3 if ﬂood

sensor functionality is selected by parameter no. 13) up to

16 nodes.

Group 9: sensor multilevel report (trigged by change of

temperature) up to 16 nodes.

Group 10: Basic on/oﬀ (triggered by change of the output Q

state and reﬂecting its state), up to 16 nodes,

Basic Set ON command is delayed for the time deﬁned in

parameter no. 77.

Basic Set OFF command is reported immediately.

Conﬁguration parameters

Parameter no. 1 Input I1 switch type –

Available conﬁg. parameters (data type is 1 Byte DEC):

 default value 1

 - mono-stable switch type (push button) 0

 - -stable switch type 1 bi

Parameter no. 2 Input I2 switch type –

See parameter 1 (valid for I2 instead of I1)

Parameter no. 3 Input I3 switch type –

See parameter 1 (valid for I3 instead of I1)

Parameter no. 4 Input 1 contact type –

Available conﬁg. parameters (data type is 1 Byte DEC):

 default value 0

 - NO (normally open) input type 0

 - NC (normally close) input type 1

NOTE: This parameter has inﬂuence only when parameter

no. 11 is set to the value “2”. After setting this parameter,

switch the window sensor once, so that the module could

determine the input state.

Parameter no. 5 Input 2 contact type –

See parameter 4 (valid for I2 instead of I1)

NOTE: This parameter has inﬂuence only when parameter

no. 12 is set to the value “2000”. After setting this

parameter, switch the condense sensor once, so that the

module could determine the input state.

Parameter no. 6 Input 3 contact type –

See parameter 4 (valid for I3 instead of I1)

NOTE: This parameter has inﬂuence only when parameter

no. 13 is set to the value “2”. After setting this parameter,

switch the ﬂood sensor once, so that the module could

determine the input state.

Parameter no. 10 - Activate / deactivate functions ALL

ON/ALL OFF

Available conﬁg. parameters (data type is 2 Byte DEC):

 default value 255

 - ALL ON active, ALL OFF active. 255

 - ALL ON is not active ALL OFF is not active 0

 - ALL ON is not active ALL OFF active 1

 - ALL ON active ALL OFF is not active 2

Flush thermostat module responds to commands ALL PWM

ON / ALL OFF that may be sent by the main controller or by

other controller belonging to the system.

Parameter no. 11- I1 Functionality selection

Available conﬁg. parameters (data type is 2 Byte DEC):

 default value 1

 input I1 doesn Heat/Cool 32767 – ’t influence on the

process

 - input I1 changes the mode of the thermostat 1

between Oﬀ and Heat/Cool. In this case function on window

sensor is disabled

 - input I1 inﬂuences on heating/cooling valves 2

according to status of window sensor. In this case function

of Oﬀ and Heat/Cool selection by I1 is disabled.

NOTE: If "Window Sensor" selected (value set to "2"),

parameter 100 (enable/disable endpoint) must be set to

non zero value and module re-included!

Parameter no. 12 I2 Functionality selection –

Available conﬁg. parameters (data type is 2 Byte DEC):

 default value 32767

 - input I2 does not inﬂuence on the Heat/Cool 32767

process

 From 0 to 990 - Temperature set point from 0.0 °C to

99.0 °C. When I2 is pressed, it automatically set

temperature setpoint according to value defined here. In

this case function of condense sensor is disabled

 From 1001 to 1150 - Temperature set point from -0.1

°C to 15.0 °C- . When I2 is pressed, it automatically set

temperature setpoint according to value deﬁned here. In

this case function of condense sensor is disabled

 - Input I2 inﬂuences on the cooling valve 2000

according to status of condense sensor, In this case

function of setpoint selection with I2 is disabled

NOTE: If "Condense Sensor" selected (value set to "2000"),

parameter 101 (enable/disable endpoint) must be set to

non zero value and module re-included!

Parameter no. 13 I3 Functionality selection –

Available conﬁg. parameters (data type is 2 Byte DEC):

 default value 32767

 - input I3 does not inﬂuence on the heat/cool 32767

process

 - input I3 changes the mode of the thermostat 1

between Heat and Cool and override parameter 59. In this

case function on ﬂood sensor is disabled NOTE: After

parameter change, ﬁrst exclude module (without setting

parameters to default value) and then re include the

module!

 - input I3 inﬂuences on heating/cooling valves 2

according to status of ﬂood sensor. In this case function of

Heat/Cool selection by I3 is disabled

NOTE1 If this parameter is changed, it is necessary to re-:

include the module.

NOTE2: If "Flood Sensor" selected (value set to "2"),

parameter 102 (enable/disable endpoint) must be set to

non zero value and module re-included!

Parameter no. 40 Power reporting in Watts on power –

change

Set value means percentage, set value from 0 - 100=0% -

100%. Available conﬁguration parameters (data type is 1

Byte DEC):

 default value 0

 - reporting disabled 0

 1-100 = 1%-100% Reporting enabled. Power report is

send (push) only when actual power in Watts in real time

changes for more than set percentage comparing to

previous actual power in Watts, step is 1%.

NOTE If power changed is less than 1W, the report is not :

send (pushed), independent of percentage set.

Parameter no. 42 Power reporting in Watts by time –

interval

Set value means time interval (0 ) in seconds, –32767

when power report is send. Available conﬁg. parameters

(data type is 2 Byte DEC):

 default value 0 (power report is disabled)

 - reporting disabled 0

 - 1 32767 32767 = 1 second - seconds. Reporting

enabled. Power report is send with time interval set by

entered value.

Parameter no. 45 –Antifreeze

Set value means at which temperature the device will be

turned on even if the thermostat was manually set to oﬀ.

Available conﬁg. parameters (data type is 2 Byte DEC):

 default value 50 (5,0 °C)

 - 0 127 = 0,0°C … 12,7 °C

 - 1127 = - - 1001 0,1°C … 12,6 °C

 - Antifreeze functionality disabled 255

NOTE: Antifreeze is activated only in heating mode.

Parameter no. 50 - PWM maximum value

Available conﬁg. parameters (data type is 1 Byte DEC):

 default value 100 (Maximum PWM value)

 2-100 = 2%-100%, step is 1%. Maximum PWM set by

entered value

NOTE: The maximum level may not be lower than the

minimum level!

Parameter no. 51 - PWM minimum value

Available conﬁg. parameters (data type is 1 Byte DEC):

 Default value 0 (Minimum dimming value is 0%)

 1- 99 = 1% - 99%, step is 1%. Minimum PWM set by

entered value.

NOTE: The minimum level may not exceed max. level!

Parameter no. 52 - PWM cycle duration

Available conﬁg. parameters (data type is 1 Byte DEC):

 default value 10 (Minimum dimming value is 0%)

 - 127 = 1 - 127s, step is 1s. PWM cycle duration set 5

by entered value.

NOTE: PWM cycle duration deﬁne the summary of all ON

plus OFF time periods. For example if Output is set to 70%

with PWM cycle duration of 20s, output will be ON for 14s

then OFF 6s, again 14s ON, etc…

Parameter no. 53 - PID value inside deadband

Available conﬁg. parameters (data type is 1 Byte DEC):

 default value 0 (PID value equal PWM minimum

value)

 - PID value set to LAST VALUE 1

NOTE: When value is set to PID inside deadband is “0” ,

forced to PWM minimum value. LASTVALUE means that

PID remains on same level as was before entering into

deadband.

Parameter no. 54 - PID deadband

Available conﬁg. parameters (data type is 1 Byte DEC):

 default value 5 (0,5 °C)

 0- - 127 0.0 °C to 12.7 °C, step is 0,1°C

NOTE: This parameter deﬁnes the zone where PID is not

active. If the temperature diﬀerence between actual and

setpoint is bigger than PID deadband, then the PID will start

to regulate the system, otherwise the PID is zero or ﬁxed.

Parameter no. 55 - Integral sampling time

Available conﬁg. parameters (data type is 1 Byte DEC):

 default value 5 (5s)

 0- - 0s to 127s, step is 1s 127

Parameter deﬁnes the time between samples. On each

sample the controller capture diﬀerence between SP-act.

Parameter no. 56 - P parameter

Available conﬁg. parameters (data type is 2 Byte DEC):

 default value 100

 -1000 - P value, step is 1 0

Parameter no. 57 - I parameter

Available conﬁg. parameters (data type is 2 Byte DEC):

Service button (used to add or

remove module from the Z-

Wave network in case of 24 V

SELV power supply).

Produkt Specifikationer

Mærke:	Qubino
Kategori:	Termostat
Model:	Flush PWM

Har du brug for hjælp?

Hvis du har brug for hjælp til Qubino Flush PWM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Qubino Manualer

Qubino Flush Heat & Cool Manual

27 August 2024

Qubino Flush PWM Manual

27 August 2024

Termostat Manualer

Nyeste Termostat Manualer

Tru Components TK4S-14RC Manual

18 December 2024

Tru Components TCN4S-24R Manual

18 December 2024

ATTACK OT80 Manual

17 December 2024

Warmup +Kit Manual

17 December 2024

Warmup 5iE Manual

17 December 2024

Tru Components TX4S-14R Manual

17 December 2024

EQ-3 CC-RT-O-CnL-W-R5-2 Manual

16 December 2024

EQ-3 HmIP-WTH-2 Manual

16 December 2024

EQ-3 HMIP-WTH Manual

16 December 2024

EQ-3 HMIP-eTRV Manual

16 December 2024