Renkforce RF-BTR-1000 Manual


Læs nedenfor 📖 manual på dansk for Renkforce RF-BTR-1000 (6 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 26 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/6
b) Rechargeable battery
The rechargeable battery is built into the product and cannot be replaced.
Never damage the rechargeable battery. Damaging the casing of rechargeable
batteries may cause an explosion or a re! Unlike conventional batteries
(e.g. AA or AAA batteries), the casing of the LiPo rechargeable battery is made of
a sensitive plastic lm.
Never short-circuit the contacts of the rechargeable battery. Do not throw the
battery or the product into open ames. This may cause a re or explosion!
Charge the rechargeable battery regularly, even when you are not using the
product. You do not need to discharge the battery before recharging it.
Never leave the battery unattended when it is charging.
Place the product on a heat-resistant surface before charging the battery. The
product may become warm when the battery is charging.
c) Persons and product
Never pour liquids over electrical devices or place objects lled with liquid next
to the product. If liquid or an object does enter the interior of the device, power
down the respective socket (e.g. switch off the circuit breaker), and then remove
the mains plug from the mains socket. Discontinue use and take the product to a
specialist repair centre.
Never use the product immediately after it has been brought from a cold room
into a warm one. The condensation generated may destroy the product. Allow the
product to reach room temperature before connecting it and putting it to use. This
may take several hours.
When charging the product, make sure that the cables are not pinched, kinked or
damaged by sharp edges.
Always lay the cables so that nobody can trip over or become entangled in them.
This may cause an injury.
Do not listen to excessively loud music over an extended period of time, as this
may cause hearing damage.
Product overview
3
1
2
4
1 Multifunction button with LED
indicator
2 3.5 mm jack plug
3 Micro USB port
4 Microphone
Operation
a) Charging the internal battery
Fully charge the battery before using the product for the rst time.
Insert the micro USB plug into the micro USB port (3) on the product, and then connect the
USB-A plug on the micro USB cable to a standard USB power source. Charging will start
automatically when the USB power source delivers a current.
The LED indicator (1) will turn red to indicate that the battery is charging.
The LED indicator will turn blue when the battery is fully charged.
Disconnect the product from the USB power source when the battery has nished charging.
b) Turning the receiver on and off
Press the multifunction button (1) for 2 seconds to turn the receiver on. The LED indicator (1)
will turn on and ash twice at long intervals.
Press the multifunction button (1) for 3 seconds to turn the receiver off. The LED display (1)
will ash red to indicate that the receiver is powering off.
c) Pairing the receiver with a Bluetooth device
The receiver needs to be paired with a Bluetooth audio device in order to receive an audio
signal.
Place the receiver and your Bluetooth audio device at a distance of approximately 1 m from
one another and avoid interferences that may affect signal transmission (for example, do not
place the devices near strong electromagnetic elds or metal objects or behind reinforced
concrete walls).
Ensure that your Bluetooth device has all of the necessary drivers installed. Visit the
manufacturer's website to download and install the latest drivers.
Turn on the Bluetooth device and enable pairing mode (if necessary).
Follow the instructions for your Bluetooth device to pair it with the receiver. These may vary
depending on the manufacturer and design. Your device will search for available Bluetooth
devices.
Hold down the multifunction button (1) for 2 seconds to enable pairing mode. The LED
indicator (1) will ash red and blue when there is no Bluetooth connection.
Operating instructions
Bluetooth music receiver for headphones
Item no. 1574605
Intended use
This product is designed to transfer audio from Bluetooth devices to an analogue audio device
with a 3.5 mm headphone socket. It is powered by a lithium polymer rechargeable battery and
connects to devices that have an analogue audio input (3.5 mm jack socket). You can also use
the receiver to answer calls from a connected mobile device.
This product is intended for indoor use only. Do not use it outdoors. Contact with moisture
(e.g. in bathrooms) must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. Using the
product for purposes other than those described above may damage the product. In addition,
improper use can cause hazards such as a short circuit, re or electric shock. Read the
instructions carefully and store them in a safe place. Make this product available to third parties
only together with its operating instructions.
This product complies with statutory national and European regulations. All company and
product names are trademarks of their respective owners. All rights reserved.
Bluetooth is a registered trademark of Bluetooth SIG, Inc. worldwide.
Delivery content
Bluetooth Music Receiver
USB charging cable (27 cm)
Operating instructions.
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
on this page. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in the triangle indicates that there is a risk to your
health, e.g. due to an electric shock.
This symbol is used to highlight important information in these operating instructions.
Always read this information carefully.
This symbol indicates special information and advice on how to use the product.
Safety information
Read the operating instructions and safety information carefully. If you do
not follow the safety instructions and information on proper handling in this
manual, we will assume no liability for any resulting personal injury or damage
to property. Such cases will invalidate the warranty/guarantee.
a) General information
This product is not a toy. Keep it out of the reach of children and pets.
Do not leave packaging material lying around carelessly, as it may become
dangerous playing material for children.
Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, ammable gases, vapours and solvents.
Do not place the product under any mechanical stress.
If it is no longer possible to operate the product safely, stop using it and prevent
unauthorized use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stress.
Always handle the product carefully. Jolts, impacts or a fall even from a low height
may damage the product.
Always observe the safety and operating instructions of any other devices which
are connected to the product.
Consult a technician if you are not sure how to use or connect the product.
Maintenance, modications and repairs must be done by a technician or an
authorized repair centre.
If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.


Produkt Specifikationer

Mærke: Renkforce
Kategori: Ikke kategoriseret
Model: RF-BTR-1000

Har du brug for hjælp?

Hvis du har brug for hjælp til Renkforce RF-BTR-1000 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Renkforce Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlona

Atlona AT-DVIF30S-IR Manual

29 December 2024
Atlona

Atlona AT-PRO3HD66M Manual

29 December 2024
Atlona

Atlona AT-3GSDI500 Manual

29 December 2024
BlueBuilt

BlueBuilt BBMAG2M Manual

29 December 2024
Atlona

Atlona AT-3GSDI-14 Manual

28 December 2024
Atlona

Atlona AT-COMP10SS Manual

28 December 2024
Atlona

Atlona AT-2VGA300SL Manual

28 December 2024
Atlona

Atlona AT-HD-V216 Manual

28 December 2024
Atlona

Atlona AT-VGA11S Manual

28 December 2024
True

True TC900 Manual

28 December 2024