Ridgid 406 Manual


Læs nedenfor 📖 manual på dansk for Ridgid 406 (10 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/10
300 and 400 Lever Bender Instruction Sheet
Inspection/Maintenance
The bender should be inspected before each use for wear or dam-
age that could affect safe use. Clean as needed to aid inspection
and to prevent handles and controls from slipping from your grip
during use.
Make sure the bender is complete and properly assembled. If any
problems are found, do not use until the problems are corrected.
Lubricate all moving parts/joints as needed with a light lubricating
oil, and wipe any excess oil from the bender.
Operation
The benders can be used either hand held or mounted in a vise. See
Figures 1 & 2 for area to be securely gripped in vise.
Spring Back
All tubing will spring back slightly after a bend is made. Amount
of spring back depends on tube characteristics. You may need to
slightly overbend the tube to compensate for spring back.
General Operation
1. Rotate the form handle and latch out of the way.
2. Position tube in form groove
and secure with the latch. At
least 1/8" (3 mm) of tube should
extend past the latch.
3. Rotate shoe insert into contact
with tube. Rotate the shoe
handle around the form until
the “0” line on the shoe insert
aligns with the desired degree
of bend on the form.
For 90° and 45° Bends:
Mark the tube at the desired distance (X) from the feature (end
of tube, bend, etc.). The center of the leg of the bend will be this
distance from the feature for 90° bends. The center of the arc will
be this distance from the feature for 45° bends.
Align the tube in the form.
a. For 90° Bends:
If the feature is to the of the mark, align the mark with the LEFT
90° line on the form.
Figure 4A Aligning for 90° Bend (LEFT)
If the feature is to the of the mark, align the mark with the RIGHT
R line on the form.
Figure 4B – Aligning for 90° Bend (RIGHT)
300 and 400 Lever Bender
Instructions
WARNING
Read these instructions and the warn-
ings and instructions for all equipment
being used before using to reduce the
risk of serious personal injury.
Always use safety glasses to reduce the risk of eye injury.
Do not use handle extensions (such as a piece of pipe).
Han dle extensions can slip or come off and increase the
risk of serious injury.
If you have any question concerning this RIDGID® product:
Contact your local RIDGID distributor.
Visit RIDGID.com or to find your local RIDGID contact point.
Contact Ridge Tool Technical Service Department at
ProToolsTechService@Emerson.com, or in the U.S. and Canada
call 844-789-8665.
Selection of appropriate materials and installation, joining
and forming methods is the responsibility of the system designer
and/or installer. Selection of improper materials and methods could
cause system failure.
Stainless steel and other corrosion resistant materials can be con-
taminated during installation, joining and forming. This contamination
could cause corrosion and premature failure. Careful evaluation of
materials and methods for the specific service conditions, including
chemical and temperature, should be completed before any instal-
lation is attempted.
Description
The RIDGID® 300 and 400 Series Lever Benders are designed to
easily bend metal tubes to a maximum of 180°. The benders have
offset cushion grip handles and 90° start angle with specially de-
signed shoe to minimize bending efforts.
The 300 Series Plumbing benders are used to bend soft copper
tubes. The 400 Series Instrument benders can be used to bend
copper, steel and stainless steel tubes with a wall thickness up to
0.06" (1,5 mm).
See RIDGID catalog for specifications for each bender.
Figure 1 300 Series Plumbing Bender
Figure 2 400 Series Plumbing Bender
Shoe Handle
Form Model Number Location
NOTICE
Latch
Shoe Insert
Mark On
Tube
X
90° Line
on Form
X
Form Handle
Form Handle
Vise Clamp Block
Shoe Handle
Shoe
Insert
Form
Latch
Model Number Location
Vise Clamp Block
Figure 3 Positioning Tube in
Bender
Before After
Before After
X
Mark On
Tube
R Line
X
Printed 11/22
890-011-232.09
ECN001818
REV. B
©2021, 2022 Ridge Tool Company
RIDGID and the Emerson logo are registered trademarks of Emerson Electric Co. or its subsidiaries in the US and other countries.
Any other trademarks belong to their respective holders.
EN


Produkt Specifikationer

Mærke: Ridgid
Kategori: Ikke kategoriseret
Model: 406

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid 406 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Ridgid Manualer

Ridgid

Ridgid HKO-186 Manual

31 August 2024
Ridgid

Ridgid Raprench 10 Manual

31 August 2024
Ridgid

Ridgid KT-190 Manual

31 August 2024
Ridgid

Ridgid 760 FXP Manual

30 August 2024
Ridgid

Ridgid 700 Manual

30 August 2024
Ridgid

Ridgid KWIK-SPIN+ Manual

30 August 2024
Ridgid

Ridgid 690-I Manual

30 August 2024
Ridgid

Ridgid 600-I Manual

30 August 2024
Ridgid

Ridgid Power Spin+ Manual

25 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024