Ridgid 408 Manual


Læs nedenfor 📖 manual på dansk for Ridgid 408 (8 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/8
300 and 400 Lever Bender Instruction Sheet
Inspection/Maintenance
The bender should be inspected before each use for wear or dam-
age that could affect safe use. Clean as needed to aid inspection and
to prevent handles and controls from slipping from your grip during
use.
Make sure the bender is complete and properly assembled. If any
problems are found, do not use until the problems are corrected.
Lubricate all moving parts/joints as needed with a light lubricating oil,
and wipe any excess oil from the bender.
Operation
The benders can be used either hand held or mounted in a vise. See
Figures 1 & 2 for area to be securely gripped in vise.
Spring Back
All tubing will spring back slightly after a bend is made. Amount of
spring back depends on tube characteristics. You may need to slight-
ly overbend the tube to compensate for spring back.
General Operation
1. Rotate the form handle and latch out of the way.
2. Position tube in form groove
and secure with the latch. At
least 1/8" (3 mm) of tube should
extend past the latch.
3. Rotate shoe insert into contact
with tube. Rotate the shoe
handle around the form until
the “0” line on the shoe insert
aligns with the desired degree
of bend on the form.
For 90° and 45° Bends:
Mark the tube at the desired distance (X) from the feature (end of
tube, bend, etc.). The center of the leg of the bend will be this dis-
tance from the feature for 90° bends. The center of the arc will be
this distance from the feature for 45° bends.
Align the tube in the form.
a. For 90° Bends:
If the feature is to the of the mark, align the mark with theLEFT
90° line on the form.
Figure 4A – Aligning for 90° Bend (LEFT)
If the feature is to the of the mark, align the mark with theRIGHT
Rline on the form.
Figure 4B – Aligning for 90° Bend (RIGHT)
300 and 400 Lever Bender
Instructions
WARNING
Read these instructions and the warn-
ings and instructions for all equipment
being used before using to reduce the
risk of serious personal injury.
Always use safety glasses to reduce the risk of eye injury.
Do not use handle extensions (such as a piece of pipe).
Han dle extensions can slip or come off and increase the
risk of serious injury.
If you have any question concerning this RIDGID®product:
Contact your local RIDGID distributor.
Visit RIDGID.com or to find your local RIDGID contact point.
Contact Ridge Tool Technical Service Department at rtctechser -
vices@em erson.com, or in the U.S. and Canada call (800) 519-
3456.
Selection of appropriate materials and installation, joining
and forming methods is the responsibility of the system designer
and/or installer. Selection of improper materials and methods could
cause system failure.
Stainless steel and other corrosion resistant materials can be con-
taminated during installation, joining and forming. This contamination
could cause corrosion and premature failure. Careful evaluation of
materials and methods for the specific service conditions, including
chemical and temperature, should be completed before any installa-
tion is attempted.
Description
The RIDGID®300 and 400 Series Lever Benders are designed to
easily bend metal tubes to a maximum of 180°. The benders have
offset cushion grip handles and 90° start angle with specially
designed shoe to minimize bending efforts.
The 300 Series Plumbing benders are used to bend soft copper
tubes. The 400 Series Instrument benders can be used to bend cop-
per, steel and stainless steel tubes with a wall thickness up to 0.06"
(1,5 mm).
See RIDGID catalog for specifications for each bender.
Figure 1 – 300 Series Plumbing Bender
Figure 2 – 400 Series Plumbing Bender
Shoe Handle
Form Model Number Location
NOTICE
Latch
Shoe Insert
Mark On
Tube
X
90° Line
on Form
X
Form Handle
Form Handle
Vise Clamp Block
Shoe Handle
Shoe
Insert
Form
Latch
Model Number Location
Vise Clamp Block
Figure 3 – Positioning Tube in
Bender
Before After
Before After
X
Mark On
Tube
R Line
X
Printed 3/21
890-011-232.10
EC45556
REV. A
©2021, Ridge Tool Company. All rights reserved
RIDGID and the Emerson logo are registered trademarks of Emerson Electric Co. or its subsidiaries in the US and other countries.
Any other trademarks belong to their respective holders.
EN


Produkt Specifikationer

Mærke: Ridgid
Kategori: Ikke kategoriseret
Model: 408

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid 408 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Ridgid Manualer

Ridgid

Ridgid HKO-186 Manual

31 August 2024
Ridgid

Ridgid Raprench 10 Manual

31 August 2024
Ridgid

Ridgid KT-190 Manual

31 August 2024
Ridgid

Ridgid 760 FXP Manual

30 August 2024
Ridgid

Ridgid 700 Manual

30 August 2024
Ridgid

Ridgid KWIK-SPIN+ Manual

30 August 2024
Ridgid

Ridgid 690-I Manual

30 August 2024
Ridgid

Ridgid 600-I Manual

30 August 2024
Ridgid

Ridgid Power Spin+ Manual

25 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AOpen

AOpen DEX5950 Manual

26 November 2024
AOpen

AOpen WB5102 Manual

26 November 2024
AOpen

AOpen DE6100 Manual

26 November 2024
AOpen

AOpen DE5900 Manual

26 November 2024
AOpen

AOpen DE7000 Manual

26 November 2024
AOpen

AOpen DE7600 Manual

26 November 2024
AOpen

AOpen DES3200 Manual

26 November 2024
AOpen

AOpen DEN5128 Manual

26 November 2024
AOpen

AOpen DES4100 Manual

26 November 2024
AOpen

AOpen DEV7610 Manual

26 November 2024