Ridgid E-12 Manual


Læs nedenfor 📖 manual på dansk for Ridgid E-12 (12 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 18 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/12
Pipe Wrench Use Guide
WARNING
Read the warnings and instruc-
tions for all equipment and material
being used before operating this
tool to reduce the risk of serious
personal injury or death.
Use personal protective equipment. Always wear eye
protection. Protective equipment such as non-skid safety
shoes, hard hat, etc. used for appropriate conditions will
reduce the risk of personal injury.
Do not use handle extensions (“cheaters”). Handle
extensions may damage the wrench or slip and cause
serious injury.
Do not use with a threading machine to install or
remove (make or break) fittings. This can cause striking
or crushing injuries.
Do not use come-a-longs, chain hoists, handle exten-
sions, backhoes, threading machines, drill rigs or
other mechanical, hydraulic or powered devices to
activate pipe wrenches to install or remove (make
or break) fittings. Do not use excessive force. Pipe
wrenches are hand tools designed to be used by hand.
Use of these types of devices with pipe wrenches can
result in wrench and equipment damage and failure from
overload and increases the risk of striking, crushing or
other serious injuries or death.
Do not use a wrench with a bent or twisted handle.
A bent handle indicates the wrench has been overloaded
and is damaged. A bent handle should never be straight-
ened. Remove bent or twisted wrenches from service.
Do not modify or alter a pipe wrench. Modifying a pipe
wrench may result in wrench failure and serious injury.
Do not overreach. Keep proper footing and balance at
all times. This enables better control of the tool in unex-
pected situations.
Do not hit a wrench with a hammer to break loose
a fitting. Impact loading may damage the wrench, chip
wrench teeth or cause serious injury.
Do not misuse pipe wrenches. Misuse increases the
risk of serious injury.
Do not use as a hammer.
Do not apply a side load to the handle.
Do not use as a lever, lifting device or bender.
Do not use the wrench on hard, square, hexagonal or
other non-round material.
Pipe Wrench Use Guide
Pipe wrenches are designed to turn pipe. Improper use
may result in damage or injury.
Do not use near flame or high heat. Teeth on the hook
or heel jaw could become soft. This may result in chipping
or flattening of the teeth. This reduces its strength which
may result in failure.
Properly support the work piece. Failure to properly
support the work piece can cause falling or shifting pipe
and equipment and increases the risk of injury.
When using pipe wrenches with other RIDGID
® prod-
ucts, follow the instructions supplied with that product.
Stay alert, watch what you are doing and use common
sense when using tools. Do not use when you are tired
or under the influence of drugs, alcohol or medication.
A moment of inattention while operating tools may result
in serious personal injury.
Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles. A careless action can cause severe injury in a
fraction of a second.
Pipe wrenches are general use tools that can be used in a
variety of situations. Ridge Tool cannot provide guidance on
all possible use situations. Users must evaluate the specific
work scenario and apply training, good work practices and
methods to reduce risk.
NOTICE Selection of appropriate materials and installation,
joining and forming methods is the responsibility of the system
designer and/or installer. Selection of improper materials and
methods could cause system failure.
Stainless steel and other corrosion resistant materials can
be contaminated during installation, joining and forming. This
contamination could cause corrosion and premature failure.
Careful evaluation of materials and methods for the specific
service conditions, including chemical and temperature,
should be completed before any installation is attempted.
If you have any questions concerning this RIDGID® product:
Contact your local RIDGID distributor.
Visit RIDGID.com to find your local RIDGID contact point.
Contact Ridge Tool Technical Service Department at
rtctechservices@emerson.com or in the U.S. and Canada
call (800) 519-3456.
Printed 5/21
EC45546
999-888-101.10
REV. B
© 2018, 2021 Ridge Tool Company. All rights reserved..
RIDGID and the Emerson logo are registered trademarks of Emerson Electric Co. or its subsidiaries in the US and other countries.
Any other trademarks belong to their respective holders.
EN 1
FR 5
ES 9


Produkt Specifikationer

Mærke: Ridgid
Kategori: Ikke kategoriseret
Model: E-12

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid E-12 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Ridgid Manualer

Ridgid

Ridgid HKO-186 Manual

31 August 2024
Ridgid

Ridgid Raprench 10 Manual

31 August 2024
Ridgid

Ridgid KT-190 Manual

31 August 2024
Ridgid

Ridgid 760 FXP Manual

30 August 2024
Ridgid

Ridgid 700 Manual

30 August 2024
Ridgid

Ridgid KWIK-SPIN+ Manual

30 August 2024
Ridgid

Ridgid 690-I Manual

30 August 2024
Ridgid

Ridgid 600-I Manual

30 August 2024
Ridgid

Ridgid Power Spin+ Manual

25 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlona

Atlona AT-DVIF30S-IR Manual

29 December 2024
Atlona

Atlona AT-PRO3HD66M Manual

29 December 2024
Atlona

Atlona AT-3GSDI500 Manual

29 December 2024
BlueBuilt

BlueBuilt BBMAG2M Manual

29 December 2024
Atlona

Atlona AT-3GSDI-14 Manual

28 December 2024
Atlona

Atlona AT-COMP10SS Manual

28 December 2024
Atlona

Atlona AT-2VGA300SL Manual

28 December 2024
Atlona

Atlona AT-HD-V216 Manual

28 December 2024
Atlona

Atlona AT-VGA11S Manual

28 December 2024
True

True TC900 Manual

28 December 2024