Roland A-01 Manual

Roland Hi-Fi system A-01

Læs nedenfor 📖 manual på dansk for Roland A-01 (1 sider) i kategorien Hi-Fi system. Denne guide var nyttig for 39 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

7Top panel

1Ribbon controllers (C1, C2)

These are touch-type controllers.

* From the left, they are numbered C1 and C2.

2Operation buttons

Use these to make settings for the A-01.

3Rotary encoders (R1–R4)

Use these to control external devices.

(Subsequently, we’ll call these “encoders.”)

* From the left, they are numbered R1, R2, R3,

and R4.

4Bluetooth LED

This LED is lit blue when a connection Bluetooth

is enabled.

7Rear panel

5[POWER] switch

Turns the power on/o.

* Before turning the unit on/o, always be

sure to turn the volume down. Even with

the volume turned down, you might hear

some sound when switching the unit on/o.

However, this is normal and does not indicate

a malfunction.

6Micro USB port

Connect this to your computer so that MIDI data

can be transferred.

7[VOLUME] knob

Adjusts the output of the built-in speakers,

PHONES jack.

8PHONES jack

Connect your headphones here.

9CV OUT jack, GATE OUT jack

MIDI messages from the A-01 or from an external

device are converted to single-note CV/GATE

signals and output from these jacks.

MIDI IN connector, MIDI OUT connector

Connect these to your MIDI equipment to receive

or send MIDI messages.

Connecting Your Equipment

Connecting a computer

1. Using a commercially available USB cable (A-micro B-type), connect the A-01 to your computer

and turn on the power of the A-01.

2. Start the DAW or sequencer software that you’re using, and specify the A-01 as the MIDI device.

Connecting a tablet

You’ll use the function to connect the A-01 to your tablet.Bluetooth

1. Power-on the A-01, and place your tablet nearby.

2. Enable the function of your tablet, and in the list of detected devices, choose “Roland Bluetooth

A-01.”

When the connection is established, the A-01’s LED is lit.Bluetooth

3. Start the app that you’re using, and specify the A-01 as the Bluetooth MIDI device.

2 3

5 6 7 8 9 10

CAUTION

Take care not to connect these jacks to your

headphones or earphones. Doing so will cause

malfunctions.

By using the A-01 in conjunction with

the separately sold K-25m keyboard

unit, you can use it as a synthesizer

equipped with a keyboard.

Panel Descriptions

SEQ mode contains settings for the entire pattern (16 steps) and settings for each individual step.

Playing/stopping the pattern

To play the pattern, press the [s] button. To stop the pattern, press the [s] button once again.

Settings for the entire pattern

1. As shown in the table below, make settings for the entire pattern.

Parameter Explanation Controller

Step Species the number of steps (1–16). Encoder (R1)

Shue Adjusts the rhythmic swing of the notes. Encoder (R2)

Step Order

Species the playback order of the steps.

Normal Normal (default)

EvenOdd Invert even/ odd-

numbered

Odd Odd-numbered only

Even Even-numbered only

O0EOdd-numbered only

Even-numbered only

E0OEven-numbered only

Odd-numbered only

Random Random

Encoder (R3)

Tempo Species the tempo (40–240 bpm) of the pattern.

* The [MENU] button blinks at the specied tempo. Encoder (R4)

Gate Time

Species the same note duration for all steps.

* It is not possible to enter a tie in the overall settings. To enter a tie,

make settings for each individual step.

Ribbon

controller (C2)

Scale

Select one of the

following four as the

note length value of

each step.

[INC], [DEC]

button

O Step

Inputs the “Rest“ or “Skip“ to all blank steps.

Rest: Hold down a [1]–[4] button and press [C] button.

Skip: Hold down a [1]–[4] button and press [A] button.

—

Creating a pattern: Inputting and editing steps

1. Use the [ ][ ] buttons to select the block that you want to input.C A

2. Use the [1]–[4] buttons to enter (turn on/o) each step.

* Enter a tie: Hold down a [1]–[4] button and press [INC] button.

Enter a tie O: Hold down a [1]–[4] button and press [DEC] button.

3. As shown in the table below, specify how each step will sound.

Parameter Explanation Editing procedure

Key Species the pitch of the step. Hold down a [1]–[4] button and

turn the encoder (R1).

Gate Time Species the duration of the note.

To enter a tie, set this value to 101%.

Hold down a [1]–[4] button and

turn the encoder (R2).

Cuto Species the cuto frequency of the low pass lter. Hold down a [1]–[4] button and

turn the encoder (R3).

Resonance Emphasizes the overtone components in the region of

the low pass lter’s cuto frequency.

Hold down a [1]–[4] button and

turn the encoder (R4).

Velocity Species the strength (velocity) of the note.

While holding down one of the

[1]–[4] buttons, press the [I]

button and turn encoder (R1).

4. Repeat steps 1–3 to create your pattern.

Recalling or saving a pattern

Here’s how to recall or save a pattern.

1. Use the [BANK 1] [BANK 2] buttons to select a bank.

2. Press one of the [OSC], [FIL], [ENV], [LFO], or [S1]–[S4] buttons to recall a pattern. By long-pressing

a button, you can save the pattern.

* When you save a pattern, the newly-saved pattern overwrites the previously-saved pattern.

Step operations

Select a bank Play/stop

[32]

[16]

[16T]

[8T]

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Using SEQ Mode

English

Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (leaet “USING THE UNIT SAFELY” and Owner’s Manual.)

After reading, keep the document(s) including those sections where it will be available for immediate reference.

The A-01 is a MIDI controller with two ribbon controllers and four rotary encoders. You can assign any MIDI messages to these controllers, and use them to control your DAW or external MIDI device. In addition,

the A-01 contains an 8-bit CPU sound module and a step sequencer, allowing you to also use it as a stand-alone synthesizer.

The A-01 also supports the standard, and can wirelessly exchange MIDI data with a mobile device such as a tablet or smartphone.Bluetooth® Smart

Introduction

Here’s how to make system settings for the A-01 and MIDI-related settings.

1. Press the [MENU] button.

2. Use the [ ][ ] buttons to select a parameter, H I

and use the [DEC] / [INC] buttons to specify

a value.

3. When you have nished making settings,

press the [MENU] button to return to the

original mode.

Parameter list

SYSTEM parameter Value Explanation

Master Tune -64–63 Species the master tuning.

System Tempo 40-240

Species the basic tempo. If synchronization (slave) is disabled, the

tempo of the pattern will be the value that you specify here.

* When you change this value, the tempo of the currently-recalled

pattern also changes.

LCD Contrast 1–10

Adjusts the brightness of the display.

Auto O O, 30 min

Species the time after which the power automatically turns o if

the unit has not been operated.

* Auto O does not occur if the unit is USB-connected.

Eco Mode O, 3 sec,

10 sec, 1 min

Species the time after which the display is dimmed if the unit has

not been operated.

Bluetooth LE O, On Turns communication on/o.Bluetooth

Bluetooth LE Name O, 1–9 Species the name that is displayed for the device.Bluetooth

Key Velocity

Species the velocity value that is transmitted when you play the

keyboard.

Touch The transmitted velocity corresponds to the force with which you

play the key.

1–127 A xed velocity is always transmitted, regardless of the force with

which you play the key.

Velo Curve

Species the keyboard touch.

Light The keyboard feels light.

Normal The keyboard feels normal.

Heavy The keyboard feels heavy.

MIDI Clock

Auto

The tempo automatically synchronizes to MIDI clock (default).

Internal

The tempo specied on the A-01 unit is used. Choose the “Internal”

setting if you don’t want to synchronize to an external device.

CV Scale -63–+63 Adjusts the output scale of the CV signal.

CV Fine Tune -100–+100

Applies a ne adjustment to the output voltage of the CV signal.

CV Ref Note C0–C4 Species the note number (in steps of an octave) for which the

output of the CV OUT jack will be 0 V.

Bulk Dump Execute, Cancel

Transmits controller settings, tones, and

patterns via MIDI. Execute: [4] button

Cancel: [DEC] button

Factory Reset Resets the unit to the factory-set state.

PATCH parameter Value Explanation

Bank Select MSB 0–127 Species the bank select MSB value.

Bank Select LSB 0–127 Species the bank select LSB value.

Program Change 1–128 Species the program change value.

C1 Hold O

On (hold value)

This setting species whether the value is held or returned to 0

when you release your nger from a ribbon controller (C1, C2).

C2 Hold

Note Scale 16 Types Selects the scale (such as Chromatic or Major) that is used when

using the ribbon controller (C1) to play preview sounds.

Seq Tx Ch 1–16 Species the channel on which the MIDI messages of SEQ mode

(step sequencer) are transmitted.

Synth Ctrl Src ALL, KEYBOARD,

16STEPSEQ,

MIDI ch 1–16

Selects the source that plays the synth.

CV/GATE Ctrl Src Selects the signal that is output from the CV OUT jack and GATE

OUT jack.

CV Portamento SW

Applies a portamento eect to the CV signal.

O Portamento is not applied.

Always Portamento is always applied.

Legato Portamento is applied only when you play legato.

CV Portamento Time 1–127

Species the time of the portamento eect that is applied to the CV

signal. Higher values make the portamento apply more slowly.

CV Pitch Bend Range 1–12 Species the range of pitch bend in semitone units.

SysEX 1

Type:

Roland, Normal

Specify the system exclusive messages that are assigned to the

ribbon controllers (C1, C2) or encoders (R1–R4).

SysEX 2

SysEX 3

SysEX 4

System Settings

Memory

CONTROLLER mode:

16 patches (4 patches x 4 banks)

SYNTH mode:

16 tones (8 tones x 2 banks)

SEQ mode:

16 patterns (8 patterns x 2banks)

Power

Supply

Rechargeable Ni-MH battery (AA,

HR6) x 4, Alkaline battery (AA, LR6) x

4, USB bus power

Current

Draw 500 mA (USB bus power)

Dimensions

300 (W) x 128 (D) x 46 (H) mm

11-13/16 (W) x 5-1/16 (D) x 1-13/16 (H)

inches

Weight 950 g (including batteries)

2 lbs 2 oz

Accessories

Owner’s Manual, Leaet “USING THE

UNIT SAFELY,” Alkaline battery (AA,

LR6) x 4

Options

(sold

separately)

Keyboard unit: K-25m

* In the interest of product improvement, the specications and/or appearance of this unit are subject to change

without prior notice.

Main Specications Roland A-01: CONTROLLER + GENERATOR

In SYNTH mode, the A-01 performs the functions that are printed below each operation button.

Creating a tone

1. Press the button corresponding to the item (OSC, FIL, ENV, LFO) that you want to edit.

The parameters are displayed.

Button or encoder corresponding to the parameter for each item

S1 S2 S3 S4 R1 R2 R3 R4

OSC Saw Square

PWM

Noise

Portamento Portamento

Time Octave

FIL Type1 Type2 Type3 OFF Cuto Resonance Envelope

Mod LFO Mod

ENV Envelope — — Attack Decay Sustain ReleaseGate

LFO Sine Square Random LFO Mod LFO Rate LFO PWM (Zoom)Saw

* PWM: Pulse Width Modulation, Mod: Modulation

2. To edit a parameter, operate the button (S1–S4) or encoder (R1–R4) corresponding to that

parameter.

* Parameters that are assigned to the buttons (S1–S4) allow you to select one choice.

* In LFO, the Zoom parameter lets you change the magnication of the audio waveform.

3. Repeat steps 1 and 2 to create your tone.

Recalling or saving a tone

Here’s how to recall or save a tone.

1. Use the [BANK 1], [BANK 2] buttons to select a bank.

2. Press one of the [OSC], [FIL], [ENV], [LFO], or [S1]–[S4] buttons to recall a tone. By long-pressing a

button, you can save the tone.

* When you save a tone, the newly-saved tone overwrites the previously-saved tone.

Performing

So that you can perform using the separately sold K-25m keyboard unit, the default settings assign

pitch bend to ribbon controller (C1) and modulation to ribbon controller (C2). By pressing the [s]

button you can play back the step sequencer.

Using SYNTH Mode

The A-01 has three modes: CONTROLLER, SYNTH, and

SEQ. Press the [MODE] button to switch between these

modes.

7CONTROLLER Mode

In CONTROLLER mode you use the two ribbon controllers (C1, C2) and four encoders to control your

MIDI equipment. The assignments of each controller can be saved in buttons [1]–[4].

7SYNTH Mode

In SYNTH mode you can create sound by editing the settings of the oscillator, lter, envelope, and

LFO. You can save up to 16 of the sounds (tones) that you create (8 tones x 2 banks).

7SEQ (Step Sequencer) Mode

The A-01 operates as a 16-step step sequencer, allowing you to view and edit the steps in four

blocks each containing four steps.

Switching the Mode (CONTROLLER / SYNTH / SEQ)

In CONTROLLER mode, the A-01 performs the functions that are printed above each operation button.

Editing the settings

To edit the settings, use the [C] [A] [=] [?] buttons

to move to an item, and use the [INC] [DEC] buttons to

edit the parameter.

Recalling and saving a patch

You can recall or save controller settings for the patch as follows. Up to 16 sets of patches (4 patches × 4

banks) can be saved.

1. Hold down the [ ] button and use the [1]–[4] buttons to select a bank.?

2. Press one of the [1]–[4] buttons to recall a patch. If you long-press a button, the current settings

are saved in that number.

* When you save the settings, the previously-saved settings are overwritten by the newly-saved

settings.

The parameter you’re editing

Using CONTROLLER Mode

The A-01 operates on batteries or on USB bus power. If using the unit on batteries, install four AA

batteries, ensuring that the batteries are oriented correctly.

* When the batteries run low, the LED at the top of ribbon controller (C1) blinks. Please install new

batteries.

* If you handle batteries improperly, you risk explosion and uid leakage.

* This unit is equipped with a protection circuit. A brief interval (a few seconds) after turning the

unit on is required before it will operate normally.

* The power to this unit will be turned o automatically after a predetermined amount of time has

passed since it was last used for playing music, or its buttons or controls were operated (Auto O

function). If you do not want the power to be turned o automatically, disengage the Auto O

function.

• Any settings that you are in the process of editing will be lost when the power is turned o. If

you have any settings that you want to keep, you should save them beforehand.

• To restore power, turn the power on again.

Important Notes

Switching between modes

CONTROLLER SYNTH SEQ

Produkt Specifikationer

Mærke:	Roland
Kategori:	Hi-Fi system
Model:	A-01

Har du brug for hjælp?

Hvis du har brug for hjælp til Roland A-01 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hi-Fi system Roland Manualer

21 September 2024

14 September 2024

8 September 2024

8 September 2024

2 September 2024

Roland RUBIX24 Manual

1 September 2024

Roland OCTA-Capture Manual

13 August 2024

Roland OD-20 Manual

12 August 2024

Roland GX-700 Manual

12 August 2024

Roland FR-1X Manual

11 August 2024

Hi-Fi system Manualer

Nyeste Hi-Fi system Manualer

Korg Nu 1 Manual

15 November 2024

Kenwood UD-F5 Manual

15 November 2024

Krüger&Matz KM1961 Manual

15 November 2024

Auna VCP-191 Manual

15 November 2024

Denon CEOL N-8 Manual

15 November 2024

Samsung MAX-DC20900 Manual

10 November 2024

Samsung MAX-X65 Manual

10 November 2024

Samsung MAX-DT95 Manual

10 November 2024

Samsung MAX-DA67 Manual

10 November 2024

Numan Retrospective 1978 MKII Manual

3 November 2024