Römer Advansafix II Manual
Læs nedenfor 📖 manual på dansk for Römer Advansafix II (2 sider) i kategorien Autostol. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
A correctly adjusted headrest 07 ensures optimal protection
for your child in the safety seat:
The headrest 07 must be adjusted so that the shoulder belts
08 are at the same level as your child’s shoulders.
CAUTION! The shoulder belts 08 must not run behind the
back of the child or at ear height or above the ears.
The shoulder belts are adjusted as follows:
1. Loosen the 5-point harness 38 of the child seat as much
as possible.
Back side of the child seat:
2. Press the button of the shoulder belt height adjuster 10 at
the rear of the seat shell and tilt the shoulder belt height
adjuster 10 towards you.
3. Slide the shoulder belt height adjuster 10 to select the
correct height of the shoulder belts 08 and engage it in the
positon that fits for your child by releasing the button.
A correctly adjusted headrest 07 ensures that the diagonal
seat belt section 11 is optimally positioned, and gives your
child the optimal protection.
The headrest 07 must be adjusted so that there is a space
two fingers wide between the headrest 07 and your child‘s
shoulders.
To adjust the height of the headrest to fit your child:
1. Squeeze the adjustment handle 12 on the back of the
headrest 07 .
This unlocks the headrest.
2. You can now move the unlocked headrest 07 to the
desired height. As soon as you release the adjustment
handle 12 the headrest 07 will lock into place.
3. Place the child seat on the vehicle seat.
4. Have your child sit down in the child seat and check the
height. Repeat this process until the headrest 07 is at
the optimal height. If in the lowest position the headrest
07 is still too high, additional adjustment can be made
through the shoulder belt height adjuster 10 , as explained
in section 5.2
5.3. Adjusting the headrest in vehicle belt installation
1. If your vehicle is not equipped with the ISOFIX insert guides
as standard, clip the two insert guides 02 which are in-
cluded with the seat* with the cut-out facing upwards onto
the two ISOFIX attachment points 01 of your vehicle.
TIP: The ISOFIX attachment points are located between the
surface and the backrest of the vehicle seat.
2. Move the head restraint on the vehicle seat to the upper
position.
3. Pull the grey fabric loop 03 to pull out both locking arms
15 until you hear a click sound which indicates they are
fully engaged.
4. On both sides of the seat squeeze the green safety button
04 and the red release button 05 together and remove
the connector protection 06 .
* The insert guides make it easier to install the child safety seat with the aid of the ISOFIX
attachment points and prevent damage to the seat covering. When not in use, they should
be removed and stored in a safe place. On vehicles with a folding backrest the insert guides
must be removed before the backrest is folded.
Any problems which occur are usually caused by dirt or foreign objects on the insert guides
and on the hooks. Clean o any dirt or foreign objects to remedy this type of problem.
5. PREPARATORY WORK
5.1 Prepare ISOFIX
5.2 Adjusting the headrest in 5-point harness installation
02
01
Please read the chapter with your desired installation method in chapter 6 first.
07
08
10
07
11
12
38
For the safety of your child, before every journey in the car check that...
►the child safety seat is engaged on sides with the ISOFIT locking arms both 15 in the
ISOFIX attachment points 01 and that both green safety buttons 04 are completely
green;
►the child seat is firmly installed in the vehicle;
►the SICT A is correctly installed and used (only ADVANSAFIX II SICT).
►the belt is not twisted;
►the Top Tether 13 is tightly tensioned over the backrest of the car seat and the tension
indicator 18 is green;
►the diagonal belt runs through the dark red belt guide 25 ;
►the straps of the child safety seat are close to the body without constricting the child;
►the shoulder belts 08 are correctly adjusted and the straps are not twisted;
►the shoulder pads 19 are at the same level as your child´s shoulders;
►the buckle latches 20 are engaged in the harness buckle 21 ;
Caution: If your child attempts to open the green safety buttons 04 or the harness
buckle 21 , make sure to stop at the earliest opportunity. Check that the child safety
seat is correctly attached and make sure that your child is properly secured. Teach
your child about the dangers involved.
6. Grasp the child seat with both hands and slide the two lock-
ing arms 15 firmly into the insert guides 02 until the locking
arms engage with a clicking noise on both sides.
The green safety button 04 must now be visible on both
sides.
The locking arms are only correctly engaged if CAUTION!
both of the safety buttons 04 are completely green.
1. Make sure that the child seats 5-point harness is removed
and the SecureGuard is installed correctly (see section 09)
2. Follow the steps in section 5.1
3. Follow the steps in section 5.3
4. Make sure the Top Tether 13 lies over the child seat. If not,
take the Top Tether 13 from the storage bag 14 and lay it
over the child seat.
5. Place the child seat facing in the direction of travel on the
vehicle seat.
7. Push the child seat towards the backrest applying firm, even
pressure on both sides.
8. Shake the child safety seat to make sure it is safely attached
and re-check to the green safety buttons 04 to make sure
that both of them are completely green
13. Have your child sit down in the child seat.
14. Pull out the vehicle seat belt and guide it in front of your child
to the vehicle seat buckle 29.
Do not twist the belt.CAUTION!
15. Engage the buckle tongue in the vehicle seat buckle 29
CLICK!
16. Place the diagonal seat belt section 11 and lap belt section
28 on the side of the vehicle seat belt buckle 29 under the
armrest and into the light red belt guide 23 of the child seat.
CAUTION! The vehicle seat belt buckle 29 must not be
positioned between the light red belt guide 23 and the armrest.
17. Place the lap belt 28 in the light red SecureGuard 46 .
CAUTION! notDo place the diagonal seat belt section 11
in the light red SecureGuard 46 .
18. Place the lap belt section 28 on the other side of the child
seat in the light red belt guide 23 .
The lap belt section CAUTION! 28 must lie as low as
possible over your child‘s hips on both sides
19. Guide the diagonal seat belt section 11 into the dark red
belt holder 30 of the headrest 07 until it lies completely in
the belt holder 30 and is not twisted.
Tip! If the backrest 31 conceals the belt holder 30 , you can
adjust the headrest 07 upwards. The diagonal seat belt section
11 can now be easily inserted. Now return the headrest 07 to
the proper height, as in Section 5.3.
20. Make sure that the diagonal seat belt section 11 runs over
your child‘s shoulder bone, and not in front of his or her
neck.
Tip! You can still adjust the height of the headrest 07 again here
in the vehicle.
The diagonal seat belt section CAUTION! 11 must run diag-
onally backward. You can adjust the course of the belt with your
vehicle‘s adjustable belt deflector.
The diagonal seat belt section CAUTION! 11 must never
lead forward to the vehicle‘s belt deflector.
In this case, only use the child seat on the rear seat.
For the safety of your child, before every journey in the car check that...
►the child safety seat is engaged on sides with the ISOFIT locking arms both 15 in the
ISOFIT attachment points 01 and that both green safety buttons 04 are completely green;
►the child safety seat is securely fastened;
►the SICT A is correctly installed and used (only ADVANSAFIX II SICT).
►the Top Tether 13 is tightly tensioned over the backrest of the car seat and the ten-
sion indicator 18 is green;
►the lap belt section 28 runs through the light red belt guides 23 on both sides of the
seat cushion;
►the lap belt section 28 runs through the light red SecureGuard 46 .
►the diagonal seat belt section 11 on the side of the vehicle seat belt buckle 29 also
runs through the light red belt guide 23 of the seat cushion;
►the diagonal seat belt section 11 runs through the dark red belt holder 30 of the
headrest;
►the diagonal seat belt section 11 runs diagonally backward,
►the straps are tight and twisted;not
►the vehicle seat belt buckle 29 is positioned between the light red belt guide not 23
and the armrest of the seat cushion.
If your child attempts to open the safety buttons CAUTION! 04 or the harness
buckle 21 or is trying to put the diagonal seat belt section 11 in the light red
SecureGuard 46 , make sure to stop at the earliest opportunity. Check that the child
safety seat is correctly attached and make sure that your child is properly secured.
Teach your child about the dangers involved.
GROUP 2 (15-25 kg) &
GROUP 3 (22-36 kg)
With ISOFIT + Top Tether + Vehicle belt
B
To remove the child seat follow the steps in section 8
15
04
29
11
28
23
28 23
11
30
07
11 07
7. Push the child seat towards the backrest applying firm, even
pressure on both sides.
8. Shake the child safety seat to make sure it is safely attached
and re-check the green safety buttons 04 to make sure
that both of them are completely green.
6. Grasp the child seat with both hands and slide the two lock-
ing arms 15 firmly into the insert guides 02 until the locking
arms engage with a clicking noise on both sides. The green
safety button 04 must now be visible on both sides.
The locking arms are only correctly engaged if CAUTION!
both of the safety buttons 04 are completely green.
1. Make sure that the child seat´s 5-point harness is installed
correctly and the SecureGuard is NOT installed (see section
10).
2. Follow the steps in section 5.1
3. Follow the steps in section 5.2
4. Make sure the Top Tether 13 lies over the child seat. If not,
take the Top Tether 13 from the storage bag 14 and lay it
over the child seat.
5. Place the child seat facing in the direction of travel on the
vehicle seat.
GROUP 1 (9-18 kg) &
GROUP 2 (15-25 kg)
With ISOFIT + Top Tether + Vehicle belt + 5-Point Harness
A
6. INSTALLATION
13
14
15
04
9. Pull the Vehicle belt 22 out and guide it through the belt
guides 23 of the child seat. Make sure that the belt is not
twisted.
10. Engage the buckle tongue in the vehicle seat buckle 29 this
should make a click noise.
11. On the side opposite the car seat belt buckle, insert diago-
nal belt in dark red belt guide 25 .
12. Apply your body weight to the child seat (kneel into the
seat). At the same time pull the diagonal belt strongly to
tighten upwards.
13. Remove body weight from child seat and re-tension by
pulling the diagonal belt 11 .
14. Take the Top Tether 13 and press the metal tongue 16
away from the strap to lengthen the strap and pull the Top
Tether 13 by the snap hook 17 until it makes a V-shape.
15. Route the Top Tether 13 on the left and right hand sides of
the vehicle headrest.
16. Hook the snap hook
17 into the Top Tether anchoring point
recommended in your vehicle owner‘s guide.
Be sure not to use the luggage hook instead of CAUTION!
the Top Tether point. Check your vehicle and look for this
sign:
17. To Tension the Top Tether 13 remove the slack by pulling the
free end of the belt through the metal tongue 16 , equalising
the strap tension on both sides. The Top Tether is correctly
tensioned when the green tension indicator 18 is extended
by 1 cm.
18. Follow the steps in section securing your child with 5-point
harness.
22
23
25
11
17
16
29
1 cm
18
17
SECURING YOUR CHILD WITH 5-POINT HARNESS
21
26
08
19
21
27
7. CARE INSTRUCTIONS
To ensure the full protective eect of the child safety seat:
►In the event of an accident with an impact speed above 10 km/h it is possible that the
child safety seat may have been damaged, but that the damage may not be immedi-
ately obvious. In this case the child safety seat must be replaced.
Please dispose of it properly.
►Regularly check all important parts for damage. Make sure that the mechanical com-
ponents in particular are all in perfect working order.
►To prevent damage, ensure that the child safety seat does not become jammed
between hard objects (car door, seat runners etc.).
►Always have the child safety seat checked if it has been damaged (e.g. if it is
dropped).
►Never lubricate or oil parts of the child seat.
►In order to properly protect your baby, it is imperative that you install and use the
ADVANSAFIX II / ADVANSAFIX II SICT exactly as described in this manual.
Disposal of packaging Container for cardboard
Cover Residual waste, thermal utilisation
Plastic parts In accordance with the labelling in the designated container
Metal parts Container for metals
Harness straps Container for polyester
Buckle & latch Residual waste
8. REMOVAL OF THE CHILD SEAT
CAUTION! Remove the child seat from the vehicle. The child seat must never be
transported in the car if it is not properly secured.
Detach/Reattach SICT
To detach the SICT A, press both SICT fastening points B and remove the SICT A.
The SICT A can now be reattached to the product.
Group 1 and Group 2 (ISOFIT, Vehicle belt & Top Tether)
1. To release the ISOFIT fastening, squeeze the green safety button and the red
release button together,first on one side, then on the other.
2. Open the buckle of the vehicle seat belt and take the diagonal belt out.
3. To release the TopTether anchoring loosen the belt by lifting the metal tongue of the
adjuster away from the belt. Then take the spring hook out of the anchoring point.
4. Slide the ISOFIT locking arms back into the seat shell and put the connector protec-
tion on the ISOFIX.
Group 2 and Group 3 (ISOFIT & Top Tether)
1. Release vehicle seat buckle if securing the child seat.
2. To release the ISOFIT fastening, squeeze the green safety button and the red
release button together,first on one side, then on the other.
3. To release the TopTether anchoring loosen the belt by lifting the metal tongue of the
adjuster away from the belt. Then take the spring hook out of the anchoring point.
4. Slide the ISOFIT locking arms back into the seat shell and put the connector protec-
tion on the ISOFIX.
09
20
4. Make sure that your child´s back
lies flat against the backrest of
the child seat.
5. Guide the two buckle latches
20 together and engage them
before putting them into the
harness buckle 21 - this should
make a click noise.
6. Pull shoulder straps 11 to remove all slack from the lap
section ensuring the harness lies flat.
7. Pull on the adjuster strap 09 until the harness lies flat and is
close against your child‘s body.
CAUTION! Pull the adjuster strap 09 straight (not up-
wards or downwards).
CAUTION! The harness straps 27 must be positioned as
low as possible over your child‘s hips.
8. Pull down on the shoulder pads 19 to ensure they are cor-
rectly positioned.
1. Open the harness buckle 21 (press red button)
2. Press the adjusting button 26 and at the same time pull both
shoulder belts 08 forwards. Do not pull on the shoulder pads
19 .
3. Have your child sit down in the child seat.
The more snugly the harness fits over your child‘s body, the better your child will be protected.
Therefore avoid putting thick clothes on your child under the belt.
To remove the child seat follow the steps in section 8
9. Take the Top Tether 13 and press the metal tongue 16 away
from the strap to lengthen the strap and pull the Top Tether
13 by the snap hook 17 until it makes a V-shape.
10. Route the Top Tether 13 on the left and right hand sides of
the vehicle headrest.
11. Hook the snap hook 17 into the Top Tether anchoring point
recommended in your vehicle owner‘s guide.
Be sure not to use the luggage hook instead of CAUTION!
the Top Tether point. Check your vehicle and look for this
sign:
12. To Tension the Top Tether 13 remove the slack by pulling the
free end of the belt through the metal tongue 16 , equalising
the strap tension on both sides. The Top Tether is correctly
tensioned when the green tension indicator 18 is extended
by 1 cm.
17
16
1 cm
18
17
13
14
11
19
03
15
0405
06
28 46 11
21. Tighten the vehicle seat belt by pulling on the diagonal seat
belt section 11
11
A
ADVANSAFIX II SICT
:
19. Press the SICT A into both SICT fastening points B on
the side of the child seat nearest the vehicle door and clip
in the SICT A .
CAUTION! Make sure that there is a gap of approximately
5 mm between the SICT A and the vehicle
door in order to avoid pressure marks and other
damage to the door trim.
B
ADVANSAFIX II SICT
:
22. Press the SICT A into both SICT fastening points B on
the side of the child seat nearest the vehicle door and clip in
the SICT A .
CAUTION! Make sure that there is a gap of approximately 5
mm between the SICT A and the vehicle door in
order to avoid pressure marks and other damage
to the door trim.
A
B
Produkt Specifikationer
| Mærke: | Römer |
| Kategori: | Autostol |
| Model: | Advansafix II |
Har du brug for hjælp?
Hvis du har brug for hjælp til Römer Advansafix II stil et spørgsmål nedenfor, og andre brugere vil svare dig
Autostol Römer Manualer
13 Oktober 2024
15 August 2024
9 August 2024
6 August 2024
1 August 2024
1 August 2024
1 August 2024
31 Juli 2024
31 Juli 2024
25 Juli 2024
Autostol Manualer
- Autostol Silver Cross
- Autostol Baby Jogger
- Autostol Fisher-Price
- Autostol Graco
- Autostol ABC Design
- Autostol Bébé Confort
- Autostol Chicco
- Autostol Hauck
- Autostol Maxi-Cosi
- Autostol Britax-Römer
- Autostol Joie
- Autostol Stokke
- Autostol BeSafe
- Autostol Britax
- Autostol Concord
- Autostol Cybex
- Autostol Jane
- Autostol Kiddy
- Autostol Nania
- Autostol Nuna
- Autostol Osann
- Autostol Peg-Pérego
- Autostol Recaro
- Autostol Bugaboo
- Autostol Cosatto
- Autostol Joolz
- Autostol Foppapedretti
- Autostol BabyGO
- Autostol UPPAbaby
- Autostol Hema
- Autostol Be Cool
- Autostol Inglesina
- Autostol Brevi
- Autostol Clek
- Autostol Migo
- Autostol Lorelli
- Autostol Lionelo
- Autostol Kinderkraft
- Autostol Kindercraft
- Autostol Hamron
- Autostol InfaSecure
- Autostol Evenflo
- Autostol GB
- Autostol Xomax
- Autostol Chipolino
- Autostol Safety 1st
- Autostol Baninni
- Autostol Mountain Buggy
- Autostol X-Adventure
- Autostol Bertoni
- Autostol Xadventure
- Autostol Giordani
- Autostol Axkid
- Autostol Bellelli
- Autostol Burigotto
- Autostol Ellermeyer
- Autostol Disney
- Autostol Caretero
- Autostol Gesslein
- Autostol Takata
- Autostol Renolux
- Autostol Avova
- Autostol Cangaroo
- Autostol Beemoo
- Autostol Klippan
- Autostol Quax
- Autostol Kikka Boo
- Autostol Hipod
- Autostol Walser
- Autostol Kiwy
- Autostol Dreambee
- Autostol Apramo
- Autostol Mother's Choice
Nyeste Autostol Manualer
13 December 2024
13 December 2024
10 December 2024
10 December 2024
10 December 2024
4 December 2024
4 December 2024
5 Oktober 2024
5 Oktober 2024
2 Oktober 2024