Samsung RH60H90203L Manual

Samsung Køleskab RH60H90203L

Læs nedenfor 📖 manual på dansk for Samsung RH60H90203L (96 sider) i kategorien Køleskab. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/96
Refrigerator
user manual
Free Standing Appliance
imagine the possibilities
Thank you for purchasing this Samsung product.
DA68-03015R-06.indb 1 2017. 7. 7. �� 10:01
English - 3
SAFETY INFORMATION
• Warnings and Important
Safety Instructions in this
manual do not cover all
possible conditions and
situations that may occur.
It is your responsibility to use
common sense, caution,
and care when installing,
maintaining, and operating
your appliance.
• Because these following
operating instructions
cover various models,
the characteristics of your
refrigerator may dier slightly
from those described in this
manual and not all warning
signs may be applicable.
If you have any questions
or concerns, contact your
nearest service center or find
help and information online at
www.samsung.com.
Important safety symbols
and precautions:
WARNING
Hazards or unsafe
practices that may result
in severe personal
injury or death.
CAUTION
Hazards or unsafe
practices that may result
in minor personal
injury or property
damage.
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions carefully.
Unplug the power plug
from the wall socket.
Make sure the machine
is grounded to prevent
electric shock.
Call the contact center for
help.
Note.
These warning signs are
here to prevent injury to you
and others.
Please follow them carefully.
After reading this section,
keep it in a safe place for
future reference.
DA68-03015R-06.indb 3 2017. 7. 7. �� 10:01
English - 4
SEVERE WARNING
SIGNS FOR
TRANSPORTATION
AND SITE
• When transporting
and installing the
appliance,care should be
taken to ensure that no
parts of the refrigerating
circuit are damaged.
• R-600a or R-134a is used as
a refrigerant.
Check the compressor label
on the rear of the appliance
or the rating label inside the
refrigerator to see which
refrigerant is used for your
refrigerator.
• When this product contains
flammable gas (Refrigerant
R-600a),
- Refrigerant leaking from the
pipe work could ignite or
cause an eye injury.
If a leak is detected, avoid
any naked flames or potential
sources of ignition and air the
room in which the appliance
is standing for several
minutes.
- In order to avoid the
creation of a flammable gas-
air mixture if a leak in the
refrigerating circuit occurs,
WARNING
the size of the room in which
the appliance may be sited
depends on the amount of
refrigerant used.
- Never start up an appliance
showing any signs of
damage. If in doubt, consult
your dealer.
The room where the
refrigerator will be sited must
be 1m³ in size for every 8g
of R-600a refrigerant inside
the appliance.
The amount of refrigerant in
your particular appliance is
shown on the identification
plate inside the appliance.
• Refrigerant squirting out of
the pipes could ignite or
cause an eye injury.
When refrigerant leaks from
the pipe, avoid any naked
flames and move anything
flammable away from the
product and ventilate the
room immediately.
- Failing to do so may result in
fire or explosion.
- If the appliance contains
isobutane refrigerant
(R-600a), a natural gas
with high environmental
compatibility that is, however,
also combustible.
DA68-03015R-06.indb 4 2017. 7. 7. �� 10:01
English - 5
SAFETY INFORMATION
When transporting and
installing the appliance,
care should be taken to
ensure that no parts of
the refrigerating circuit are
damaged.
SEVERE WARNING
SIGNS FOR
INSTALLATION
• Do not install this
appliance in a humid,
oily or dusty location, in
a location exposed to
direct sunlight and water
(rain drops).
- Deteriorated insulation of
electrical parts may cause an
electric shock or fire.
• Do not place this refrigerator
in direct sunlight or expose to
the heat from stoves, room
heaters or other appliances.
• Do not plug several
appliances into the same
multiple power board.
The refrigerator should
always be plugged into its
own individual electrical outlet
which has a voltage rating
that matched the rating plate.
- This provides the best
WARNING
performance and also
prevents overloading house
wiring circuits, which could
cause a fire hazard from
overheated wires.
If the wall socket is loose, do
not insert the power plug.
- There is a risk of electric
shock or fire.
• Do not use a cord that shows
cracks or abrasion damage
along its length or at either
end.
• Do not bend the power cord
excessively or place heavy
articles on it.
• Do not use aerosols near the
refrigerator.
- Aerosols used near the
refrigerator may cause an
explosion or fire.
• Do not install this appliance
in a location where gas may
leak.
- This may result in an electric
shock or fire.
• The installation or any
service of this appliance
is recommended by a
qualified technician or
service company.
- Failing to do so may result
in an electric shock, fire,
DA68-03015R-06.indb 5 2017. 7. 7. �� 10:01
English - 6
explosion, problems with the
product, or injury.
• This refrigerator must be
properly installed and located
in accordance with the
manual before it is used.
• Connect the power plug in
the proper position with the
cord hanging down.
- If you connect the power
plug upside down, the wire
can get cut o and cause fire
or an electric shock.
• Make sure that the power
plug is not squashed or
damaged by the back of the
refrigerator.
• When moving the refrigerator,
be careful not to roll over or
damage the power cord.
- This constitutes a fire hazard.
• The appliance must be
positioned so that the plug is
accessible after installation.
• The refrigerator must be
grounded.
- You must ground the
refrigerator to prevent any
power leakages or electric
shocks caused by current
leakage from the refrigerator.
• Never use gas pipes,
telephone lines or other
potential lightening rods as
ground.
- Improper use of the ground
plug can result in an electric
shock.
• If the power cord is
damaged, have it
replaced immediately by
the manufacturer or its
service agent.
• The fuse on the refrigerator
must be changed by a
qualified technician or service
company.
- Failing to do so may result in
an electric shock or personal
injury.
DA68-03015R-06.indb 6 2017. 7. 7. �� 10:01
English - 7
SAFETY INFORMATION
CAUTION SIGNS FOR
INSTALLATION
• Keep ventilation
opening in the appliance
enclosure or mounting
structure clear of
obstruction.
• Allow the appliance to stand
for 2 hours after installation.
- When installing the
refrigerator, make sure both
legs contact the floor for
secure installation.
Legs are located at the
bottom back of each door.
Insert a flathead screwdriver
and turn it in the direction of
the arrow until it is level.
- Always balance the load on
each door.
- Overload on any one door
may fell the refrigerator,
causing physical injury.
CAUTION SEVERE WARNING
SIGNS FOR USING
• Do not insert the power
plug with wet hands.
• Do not store items on top of
the appliance.
- When you open or close
the door, items may fall and
cause a personal injury and/
or material damage.
• Do not put items filled with
water on the refrigerator.
- If spilled, there is a risk of fire
or electric shock.
• Do not let children hang on
the door.
- Failure to do so may cause
serious personal injury.
• Do not leave the doors of
the refrigerator open while
the refrigerator is unattended
and do not let children enter
inside the refrigerator.
• Do not allow babies or
children to go inside the
drawers.
- It can cause death from
suocation by entrapment or
personal injury.
• Do not sit on the Freezer
door.
- The door can be broken and
cause personal injury.
WARNING
DA68-03015R-06.indb 7 2017. 7. 7. �� 10:01
English - 8
• When remove the divider
from the drawer to clean
or other reason, should
reassemble the divider with
provided screws to prevent
children trapped.
• Never put fingers or other
objects into the dispenser
hole.
- Failure to do so may cause
personal injury or material
damage.
• Do not store volatile or
flammable substances such
as benzene, thinner, alcohol,
ether or LP gas in the
refrigerator.
- The storage of any of such
products may cause an
explosion.
• Do not store low
temperature-sensitive
pharmaceutical products,
scientific materials or other
low temperature-sensitive
products in the refrigerator.
- Products that require
strict temperature controls
must not be stored in the
refrigerator.
• Do not place or use electrical
appliances inside the
refrigerator, unless they are of
a type recommended by the
manufacturer.
• Do not use a hair dryer to dry
the inside of the refrigerator.
Do not place a lighted
candle in the refrigerator for
removing bad odours.
- This may result in an electric
shock or fire.
• Do not touch the inside walls
of the freezer or products
stored in the freezer with wet
hands.
- This may cause frostbite.
• Do not use mechanical
devices or any other means
to accelerate the defrosting
process, other than those
recommended by the
manufacturer.
• Do not damage the
refrigerant circuit.
• This product is intended
only for the storage
of food in a domestic
environment.
• Bottles should be stored
tightly together so that they
do not fall out.
• In the event of a gas leak
(such as propane gas,
LP gas, etc.), ventilate
immediately without touching
the power plug.
DA68-03015R-06.indb 8 2017. 7. 7. �� 10:01
English - 9
SAFETY INFORMATION
Do not touch the appliance
or power cord.
- Do not use a ventilating fan.
- A spark may result in an
explosion or fire.
• Use only the LED Lamps
provided by manufacturer or
service agent.
• Children should be
supervised to ensure that
they do not play with and/or
climb into the appliance.
• Do not disassemble or
repair the refrigerator by
yourself.
- You run a risk of causing
a fire, malfunction and/ or
personal injury.
In case of malfunction, please
contact your service agent.
• If the appliance
generates a strange
noise, a burning or smell
or smoke, unplug the
power plug immediately
and contact your nearest
service centre.
- Failing to do so may result
in an electric shock or fire
hazards.
• If you experience diculty
when changing the light,
contact service agent.
• If the products is equipped
with LED Lamps, do not
disassemble the Lamp Cover
and LED Lamps by yourself.
- Please contact your service
agent.
• If any dust or water is in the
refrigerator, pull out power
plug and contact your
Samsung Electronics service
centre.
- There is a risk of fire.
CAUTION SIGNS FOR
USING
• To get best performance
from the product,
- Do not place foods too
closely in front of the vents
at the rear of the appliance
as it can obstruct free air
circulation in the refrigerator
compartment.
- Wrap the food up properly or
place it in airtight containers
before putting it into the
refrigerator.
- Do not put any newly
introduced food for freezing
near to already existing food.
• Do not place carbonated
CAUTION
DA68-03015R-06.indb 9 2017. 7. 7. �� 10:01
English - 12
concentrated detergents,
bleaches, or cleansers
containing petroleum
products on exterior surfaces
(doors and cabinet), plastic
parts, door and interior liners,
and gaskets.
- These can scratch or
damage the material.
• Do not clean glass shelves
or covers with warm water
when they are cold. Glass
shelves and covers may
break if exposed to sudden
temperature changes or
impacts such as bumping or
dropping.
SEVERE WARNING
SIGNS FOR
DISPOSAL
• Ensure that none of the
pipes on the back of the
appliance are damaged
prior to disposal.
• R-600a or R-134a is used as
a refrigerant.
Check the compressor label
on the rear of the appliance
or the rating label inside the
refrigerator to see which
refrigerant is used for your
refrigerator.
WARNING
When this product contains
flammable gas (Refrigerant
R-600a), contact your local
authority in regard to safe
disposal of this product.
Cyclopentane is used as an
insulation blowing gas.
The gases in insulation
material require special
disposal procedure.
Please contact your local
authorities in regard to the
environmentally safe disposal
of this product.
Ensure that none of the pipes
on the back of the appliances
are damaged prior to
disposal.
The pipes shall be broken in
the open space.
• It is hazardous for anyone
other than an Authorised
Service Person to service this
appliance. In Queensland –
the authorized Service Person
MUST hold a Gas Work
Authorisation or Licence for
hydrocarbon refrigerants, to
carry out Servicing or repairs
which involve the removal of
covers. (For Australia only)
• When disposing of this
product or other refrigerators,
remove the door/door seals,
DA68-03015R-06.indb 12 2017. 7. 7. �� 10:01
English - 13
SAFETY INFORMATION
door latch so that small
children or animals cannot
become trapped inside.
Leave the shelves in place so
that children may not easily
climb inside.
Children should be
supervised to ensure that
they do not play with the old
appliance.
• Please dispose of the
packaging material for this
product in an environmentally
friendly manner.
ADDITIONAL TIPS
FOR PROPER USAGE
• In the event of a power
failure, call the local oce of
your Electricity Company and
ask how long it is going to
last.
- Most power failures that are
corrected within an hour
or two will not aect your
refrigerator temperatures.
However, you should
minimise the number of door
openings while the power is
o.
- Should the power failure last
more than 24 hours, remove
all frozen food.
• If keys are provided with the
refrigerator, the keys should
be kept out of the reach of
children and not be in the
vicinity of the appliance.
• The appliance might
not operate consistently
(possibility of temperature
becoming too warm in the
refrigerator) when sited
for an extended period of
time below the cold end of
the range of temperature
for which the refrigerating
appliance is designed.
• Do not store food which
spoils easily at low
temperature, such as
bananas, melons.
• Your appliance is frost free,
which means there is no
need to manually defrost
your appliance, as this will be
carried out automatically.
• Temperature rise during
defrosting can comply with
ISO requirements.
But if you want to prevent an
undue rise in the temperature
of the frozen food while
defrosting the appliance,
please wrap the frozen
food up in several layers of
newspaper.
DA68-03015R-06.indb 13 2017. 7. 7. �� 10:01
English - 15
SETTING UP
GETTING READY TO INSTALL THE
REFRIGERATOR
Congratulations on your purchase of the Samsung
refrigerator.
We hope you enjoy the state-of-art features and
eciencies that this new appliance oers.
Selecting the best location for the
Refrigerator
• Select a location with easy access to a water
supply.
• Select a location without direct exposure to
sunlight.
• Select a location with level (or nearly level)
flooring.
• Select a location with enough space for the
refrigerator doors to open easily.
• Select a location that allows sucient space to
the right,left, back, and top for air circulation.
• Select a location that allows you to move the
refrigerator easily if it needs maintenance or
service.
• Do not install the refrigerator in locations where
the temperature is over 43°C or below 5°C.
AA
BB
CCDD
EE
Depth “A” 718mm
Width “B” 912mm
Height “C” 1742mm
Overall Height “D” 1774mm
Depth “E” 721mm
1725mm 468mm
165
°165°
50mm
912mm
610mm
1170mm
34mm
31mm
The measurements here are based on
the design dimension, which may dier
depending on the measuring method.
Setting up your refrigerator
DA68-03015R-06.indb 15 2017. 7. 7. �� 10:01
English - 16
When moving your refrigerator
To prevent floor damage, be sure the front leveling
legs are in the up position (above the floor).
Refer to “How to level the refrigerator” in the
manual on page 21.
Flooring
For proper installation, you must place this
refrigerator on a level, hard surface that is the same
height as the rest of the floor.
This surface should be strong enough to support a
fully loaded refrigerator.
To protect the finish of the flooring, cut a large
section of the cardboard carton and place it under
the refrigerator where you are working.
When moving the refrigerator, you need to pull and
push it straight forwards or back.
Do not wiggle it from side to side.
Required Tools (Not provided)
Philips screwdriver
(+)
Flat-blade screw
driver (-)
Socket wrench
10mm
Allen wrench
5mm
SETTING UP THE REFRIGERATOR
Now that you have your new Refrigerator installed
in place, you are ready to set up and enjoy the
features and functions of the appliance.
By completing the following steps, your Refrigerator
should be fully operational.
If not, first check the power supply and electricity
source or try the troubleshooting section at the
back of this user’s guide.
If you have any further questions, contact your
Samsung Electronics service centre.
1. Place the Refrigerator in an appropriate location
with reasonable clearance between the wall and
the Refrigerator.
Refer to installation instructions in this manual.
2. Once the Refrigerator is plugged in, make sure
the interior light comes on when you open the
doors.
3. Set the Temperature control to the coldest
temperature and wait for an hour.
The Freezer will get slightly chilled and the
motor will run smoothly.
4. After powering the Refrigerator, it will take a few
hours to reach the appropriate temperature.
You can store food and drinks in the Refrigerator
after the temperature is suciently cool.
5. Once installation is complete, press the
dispenser lever to check if the water or the ice
is properly dispensed.
6. Make sure the front side of the refrigerator is 0.6
degree higher than its rear side.
DA68-03015R-06.indb 16 2017. 7. 7. �� 10:01
English - 17
SETTING UP
SETTING UP THE REFRIGERATOR
DOORS
If your entrance won’t allow the refrigerator to pass
easily through it, you can remove the doors.
Separating the water supply line from the
refrigerator
1. Pull the two water lines (which are in the Fixer)
out to the front.
2. Remove two water lines (White one is for water
and the other one is for ice) by pressing the
coupler ( ) and pulling the water line ( ) away.1 2
Make sure the
color of the water
lines match.
(1)
(2)
CAUTION
When reconnecting the supply hoses,
make sure the same colored hoses are
inserted with each other.
Reattaching the Water Supply Line
1. The Water Line must be fully Inserted to the
centre of transparent coupler to prevent water
leakage from the dispenser.
2. Insert the 2 clips in the install pack and check
that each clip holds the line firmly.
CAUTION
Center of Transparent coupler
Clip A (1/4”)
(6.35mm)
Do not cut the water line.
Gently separate it from the coupler.
Keep the clips out of the reach of children
and make sure that children do not play
with them or put them into their mouths.
DISASSEMBLE THE FREEZER
DOORS
1. Disconnect the power cord, and remove 2
cover screws using a Phillips screwdriver ( ). 1
Then open the refrigerator door and pull
the hooks on the sides to loosen the cover
(2).
Lift up the cover and towards you to
detach it (3).
- Detach the hinge cover with the door open and
then close the door once the hinge cover has
been detached.
(1)
(3)(2)
The upper hinge cover is either integrated
or separate depending on the model.
CAUTION
DA68-03015R-06.indb 17 2017. 7. 7. �� 10:01
English - 18
2. Remove the hinge cover and then disconnect
the electrical wire connector.
3. Flip the clamp ( ) up in direction ( ) and then A 1
pull it o in direction ( ).2
(A)
(1)
(A)
(2)
4. Remove the hinge ( ).B
(B)
5. Lift up the door and detach it from the
refrigerator.
• Be careful not to damage the electrical
wires when assembling or disassembling
the doors.
• Make sure the doors do not fall over and
become damaged while they are detached from
the refrigerator.
CAUTION
RE-ATTACHING THE FREEZER
DOORS
• Be sure to re-attach the Freezer Door
before re-attaching the Fridge Door.
• Before re-attaching, make sure that all the wire
connectors at the bottom of the Freezer Door
are connected.
How to Assemble Door
1. Attach the doors to the hinges at the bottom of
the refrigerator.
2. Insert the hinge ( ) into the hinge slot on the B
refrigerator and then press down over the hinge
hole on the door.
(B)
3. Insert the clamp ( ) in the direction of arrow A
( ) and then lower it in the direction of arrow 1
( ) to lock it in place.2
(A)
(1)
(A)
(2)
CAUTION
DA68-03015R-06.indb 18 2017. 7. 7. �� 10:01
English - 19
SETTING UP
4. Hook up the electrical wire connector.
5. Insert 2 front parts of the cover first, push down
on both side parts of the cover, and then secure
the cover in place using a Phillips screwdriver.
• The doors can be assembled in the
reverse order of their disassembly.
• The display may not function properly if you
neglect to connect the electrical wires while
assembling the door.
DISASSEMBLE THE
REFRIGERATOR DOORS
(SHOW CASE OF COLD
COMPARTMENT)
1. Disconnect the power cord, and remove 2
cover screws using a Phillips screwdriver ( ). 1
Then open the refrigerator door and pull
the hooks on the sides to loosen the cover
(2).
Lift up the cover and towards you to
detach it (3).
- Detach the hinge cover with the door open and
then close the door once the hinge cover has
been detached.
CAUTION
(1)
(3)(2)
2. Disassemble the housing connector.
3. Disassemble the three fastening screws on the
top hinge of the show case.
4. Disassemble the show
case.
DA68-03015R-06.indb 19 2017. 7. 7. �� 10:01
English - 20
DISASSEMBLE THE
REFRIGERATOR DOORS
1. Disconnect the power cord, and remove 2
cover screws using a Phillips screwdriver ( ). 1
Then open the refrigerator door and pull
the hooks on the sides to loosen the cover
(2).
Lift up the cover and towards you to
detach it (3).
- Detach the hinge cover with the door open and
then close the door once the hinge cover has
been detached.
(1)
(3)(2)
2. Disassemble the housing connector.
3. Push the fixer hinge up, and pull it forward to
remove it.
4. Disassemble the top hinge from the front of the
door.
5. Disassemble the show
case.
Fix the wire on the Hinge Hook to
prevent the damage on the wire when
reassembling.
RE-ATTACHING REFRIGERATOR
DOORS
To reattach the REFRIGERATOR doors, assemble
parts in reverse order.
CAUTION
DA68-03015R-06.indb 20 2017. 7. 7. �� 10:01
English - 23
SETTING UP
1. Adjust the height of the door by turning the
adjustment nut ( ) in the counterclockwise B
direction ( ) with a spanner.
(Turn it in the counterclockwise direction ( )
to increase the height of the door and in the
clockwise direction ( ) to decrease it.)
- Open the door and adjust it from the inside.
(A)
2. Once the doors are level, turn the clamping nut
( ) in the counterclockwise direction ( ) to A
tighten it.
(A)
Adjusting the level when the refrigerator
is empty can result in the refrigerator
becoming uneven again once items have
been placed inside.
If this occurs, adjust the level again.
HOW TO ADJUST THE DOOR GAP
If the gap between the refrigerator door and the
freezer door is uneven:
• Use the gap adjustor located at the top of the
refrigerator door (right side).
• Excessive force can cause the adjustor bolt to
break.
1. Remove the refrigerator
door’s hinge cover.
- Detach the hinge cover with
the door open and then close
the door once the hinge cover
has been detached.
2. Adjust the gap using a 4mm Allen wrench (not
included).
3. Rotate the bolt in the clockwise direction ( )
to widen the gap.
Rotate it in the counterclockwise direction
( ) to narrow the gap.
Adjust until the gap between the refrigerator
door and the freezer door appears even.
When arranging the cables, take caution
not to tear or peel o the cable coating.
CAUTION
DA68-03015R-06.indb 23 2017. 7. 7. �� 10:01
English - 24
HOW TO ADJUST THE
REFRIGERATOR DOOR GAP
(BACK)
If the gap between the refrigerator door and the
refrigerator is uneven:
• Use the adjustors located at the top edge inside
each door.
1. Open the door where the gap with the
refrigerator is narrower and then turn the
adjustor in the counterclockwise direction
( ) until the gap is even.
Adjus
2. Once the gap between the door and the
refrigerator has been adjusted, turn the adjustor
nut in the clockwise direction ( ) to lock the
adjustor in place.
Locking
CHECKING THE WATER
DISPENSER LINE
A water dispenser is one of the helpful features on
your new Samsung Refrigerator.
To help promote better health, the Samsung water
filter removes unwanted particles from your water.
However, it does not sterilize or destroy
microorganisms.
You may need to purchase a water purifying
system to do that.
In order for the ice maker to operate properly,
a water pressure of 20~125psi (138~862kPa)
(pound per square inch) is required.
Under normal conditions, a 170cc (5.75oz.) paper
cup can be filled in 10 seconds.
If the Refrigerator is installed in an area with low
water pressure (below 20psi), you can install a
booster pump to compensate for the low pressure.
Make sure the water storage tank inside the
Refrigerator is properly filled.
To do this, press the water dispenser lever until the
water runs from the water outlet.
Water line installation kits are available at
extra cost from your dealer.
We recommend using a water supply kit
that contains copper tubing.
The new hose-sets supplied with the
appliance are to be used and that old
hose-sets should not be reused.
Check the accessory list.
DA68-03015R-06.indb 24 2017. 7. 7. �� 10:01
English - 25
SETTING UP
Connecting to the water supply line
1. First, shut o the main water supply line.
2. Locate the nearest cold, drinking water line.
3. Follow the Water Line Installation Instructions in
the installation kit.
CAUTION
The water line must be connected to the
cold water pipe.
If it is connected to the hot water pipe, it
may cause the purifier to malfunction.
Close Main
Water pipe
Close Main
Water pipe No gap
4. After connecting the water supply to the water
filter, turn your main water supply back on and
Dispense about 3L to clear and prime the
water filter.
Connecting the water line to the
refrigerator
1. Remove the cap from water line on the unit and
insert compression nut to the water line on the
unit after disassembling from provided water
line.
2. Connect both water line from the unit and water
line in the kit.
3. Tighten the compression nut onto the
compression fitting.
Be careful no gap between two items.
4. Turn water on and check for any leakage.
No gap
Loosen a
Remove cap
Water Line from Kit
Water Line from unit
Only connect the water line to a drinkable
water source.
If you have to repair or disassemble the water line,
cut o 6.5mm of the plastic tubing to make sure
you get a snug, leak-free connection.
Before being used, the leakage in these
places should be examined.
• Samsung Warranty does not cover WATER
LINE INSTALLATION.
• It’ll be done at customer’s charge unless the
retail price includes installation cost.
• Please contact Plumber or Authorized Installer
for the installation if needed.
• If Water leakage occurs due to improper
installation, Please contact installer.
CAUTION
DA68-03015R-06.indb 25 2017. 7. 7. �� 10:01
English - 27
SETTING UP
Before calling service
- Any sounds you hear when the ice maker
dumps ice into the bucket are part of normal
operation.
- If you don’t dispense ice for a long period of
time, the ice may form clumps in the ice bucket.
If ice clumps form, remove the remaining ice
and empty the bucket.
- When ice does not come out, check for ice
stuck in the chute and remove it.
Figure 3
Ice Chute
• When Ice O blinks on the display panel,
reinsert the bucket and/or make sure it’s
installed properly.
• When the door is open, the Ice and water
dispenser do not work.
• If you close the door hard, it may cause water
spilling over the ice maker.
• To prevent dropping the ice bucket, use both
hands when removing it.
• To prevent injury, be sure to clean up any ice or
water that may have dropped on the floor.
• Do not let the children hang on the ice
dispenser or on the bucket.
They may get hurt.
• Be sure not to put your hand or any object into
the ice chute.
It may cause personal injury or damage
mechanical parts.
CAUTION
Removing residual matter inside the water
supply line after installing filter.
1. Turn ON the main water supply.
2. Push the Dispenser Lever.
3. Flush 1 gallons of water through the filter before
use. (Flush approximately 6 minutes.)
This will clean the water supply system and
remove air from the lines.
4. Additional flushing may be required in some
households.
5. Open the refrigerator door and make sure there
are no water leaks coming from the water filter.
Cubed Ice Crushed Ice
A newly installed water filter cartridge may
cause water to briefly spurt from the water
dispenser.
This is due to air getting into the line.
It should pose no problem to operation.
DA68-03015R-06.indb 27 2017. 7. 7. �� 10:01
English - 28
Check the amount of water supplied to
the ice tray.
1. Lift up the icemaker cover and gently pull it out.
2. When you press the Test button for 3 seconds,
the ice cube container is filled with water from
the water supply tap.
Check to make sure the amount of water is
correct (see the illustration below).
If the water level is too low, the ice cubes will be
small.
This is a water pressure problem from within the
main water pipes, not the refrigerator.
Ice maker
1
Test button
2
Check the water level
• It will take a few minutes for the water to
reach the correct level after you push the
Test button.
• Do not press the test button continuously when
the tray is filled with ice or water.
Water may overflow or ice jamming may occur.
• When the bucket is not installed, the ice maker
does not work.
• When Ice O blinks on the display panel,
reinsert the bucket and/or make sure it’s
installed properly.
CAUTION
DA68-03015R-06.indb 28 2017. 7. 7. �� 10:01
English - 30
(2) Lighting / °C °F (3sec)
The Lighting button serves two purposes:
- To turn the dispenser light on and o
- To switch the temperature units
between ºC and ºF.
1. Light Function
Touching the Lighting button turns on the
Dispenser LED lamp in continuous mode
so that it stays on continuously.
The button also lights up.
If you want the Dispenser lamp to come on
only when some one uses the dispenser,
press the Lighting button to turn the
continuous mode o.
2. To switch the temperature units
between ºC and ºF.
Touch and hold this button for 3 seconds
to select the temperature display you want.
Each time you press and hold the button,
the ºC and ºF temperature modes alternate
and the ºC or ºF icon lights up, indicating
your selection.
(3) Vacation / Filter Reset (3sec)
The Vacation button serves two purposes:
- To turn Vacation mode on and o
- To reset the water filter life indicator.
1. Vacation Function
If you are going on vacation or business
trip or you do not need to use the
refrigerator, press the Vacation button.
When you select vacation button for fridge
compartment o, display LED of Vacation
will be on.
It is strongly requested to remove foods
in the fresh-food compartment and do
not leave the door open when you select
Vacation function.
2. Water Filter Life Indicator Function
After you replace the water filter, touch and
hold this button for 3 seconds to reset the
water filter life indicator. When you reset
the water filter life indicator, the Filter icon
on the panel turns O.
The Filter icon will turn red to let you know
it is time to change the water filter after six
months (about 300 gallons).
Some areas have large amounts of lime in
their water, which causes the water filter to
clog more quickly.
If this is the case in your area, you will have
to change the filter more frequently than
every six months.
DA68-03015R-06.indb 30 2017. 7. 7. �� 10:01
English - 31
OPERATING
(4) Fridge / Power Cool (3 sec)
The Fridge button serves two purposes:
- To set the Fridge to your desired
temperature.
- To turn the Power Cool function on and
o.
1. To set the Fridge temperature, press
the Fridge button.
You can set the temperature between
44°F (7°C) and 34°F (1°C).
2. Power Cool function
Touch and hold this button for 3 seconds
to decrease the time needed to cool
products in the Refrigerator.
It can be helpful if you need to quickly cool
easily spoiled items or if the temperature in
the fridge has warmed dramatically.
(For example, if the door was left open)
(5) Alarm
Touching this button turns the door open
alarm on and o.
If the door alarm is set to On, an alarm
beeps if any refrigerator door is left open
for more than two minutes.
The beeping stops when you close the
door.
The door alarm function is pre-set to On in
the factory.
You can turn it o by pressing and then
releasing the Alarm button.
You can turn it back on in the same
fashion.
The icon lights up when the function is on.
When the Door Alarm function is on and
the alarm sound is triggered, the Door
Alarm Icon will blink while the alarm
sounds.
(6) Ice Maker O
The Ice Maker O button serves two
purposes:
-To turn the Ice maker on and o
-To turn the Control Lock Function on
and o.
-Note that Ice Maker O mode will be
deactivated if you press and hold the
ice lever for more than 5 seconds.
1. Ice Maker O Function
If you don’t want to make more ice, press
the Ice Maker O button.
2. Control Lock Function
Touch and hold this button for 3 seconds
to lock the display and the dispenser
buttons so the buttons cannot be used.
When Control Lock is on, the refrigerator
does not dispense ice or water, even if the
Dispenser Lever is pressed.
The Control Lock icon lights up to indicate
you’ve activated the Control Lock function.
Press for 3 seconds to unlock.
If the ice maker function is ON, and the
water line is not connected, there will be a
water valve noise from the back of the unit.
Press the Ice Maker O (Control Lock
(3sec)) button for less than 3 seconds until
the Ice O Indicator ( ) lights up.
To save electricity, the Panel Display turns o
automatically under the following conditions: When
no button has been pressed, when no doors
are open, or when no Dispenser Lever has been
pushed.
However, the icon indicating your cubed or
crushed ice selection, will stay on.
When you press a button, open a door, or push
a Dispenser Lever, the Panel Display will turn on
again.
Except for the Water, and Cubed / Crushed
Ice buttons, all function buttons will become
operational after you remove your finger from the
button you are currently pressing.
Water
The indicator is supposed to turn on at all
times as it indicates that the water can be
dispensed properly.
DA68-03015R-06.indb 31 2017. 7. 7. �� 10:01
English - 32
(7)
(8)
Cubed Ice
Crushed Ice
Press the Cubed Ice or Crushed Ice
button to select the type of ice you want
dispensed.
Each time you press the button, the cubed
and crushed ice modes alternate and
the Cubed or Crushed ice icon lights up,
indicating your selection.
If you don’t need ice, turn the function o
to save on water and energy consumption
(See Ice Maker O below).
(9) Filter
Water filter usage
This icon lights up when you need
to change the filter, usually after the
refrigerator has dispensed about 300
gallons of water (after about 6 months).
After you install the new water filter, reset
the filter indicator by touching and holding
the Hold 3sec for Filter Reset button for 3
seconds.
- If water is not dispensing or dispensing
slowly, you need to replace the water
filter because the water filter is clogged.
- Some areas have large amounts of lime
in their water, which causes the water
filter to clog more quickly.
(10) Control Lock
This icon lights up when you activate the
Lock function.
When the Control Lock icon is lit, all the
panel buttons, including the Ice button
and the dispensers, are locked and de-
activated.
Press and hold the Ice Maker O/Control
Lock button for 3 seconds to turn Control
Lock o and re-activate the panel buttons.
DA68-03015R-06.indb 32 2017. 7. 7. �� 10:01
English - 33
OPERATING
PARTS AND FEATURES
Use this page to become more familiar with the parts and features of the Refrigerator.
(This image may dierent depends on the model.)
DISPENSER MODEL
(2)
Two star
section
(4)
(13)
Deodorizer
Foldable Shelf
(Optional)
Water filter
(1)
(15)
(14)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
NORMAL MODEL
(12)
Two star
section
The temperature of two star sections is slightly higher than other freezer compartment.
DA68-03015R-06.indb 33 2017. 7. 7. �� 10:01
English - 35
OPERATING
CONTROLLING THE
TEMPERATURE
Basic temperature of Freezer and
Refrigerator Compartments
The basic and recommended temperatures of the
Freezer and Fridge compartments are -2°F and
37°F (or -19°C and 3°C) respectively.
If the temperature of the Freezer or Refrigerator
Compartments are too high or low, adjust the
temperature manually.
Controlling the Freezer temperature
RH57*
Recommend Temp (Freezer) : -2 °F (or -19 °C )
The Freezer temperature can be set between -8°F
and 5°F (or between -23°C and -15°C) to suit
your particular needs.Press the Freezer button
repeatedly until the desired temperature is shown
in the temperature display.
The temperature will change by 1°F (or 1°C) with
each press. See below.
Fahrenheit : 0°F -1°F -2°F -3°F -4°F
-5°F -6°F -7°F -8°F 5°F 4°F
3°F 2°F 1°F 0°F.
Centigrade : -18°C -19°C -20°C -21°C
-22°C -23°C -15°C -16°C -17°C
-18°C.
Keep in mind that foods such as ice cream may-
melt at 4°F (or -15.5°C).
The temperature display will move sequentially
from -8°F to 5°F (or from -23°C to -15°C).
Controlling the Fridge temperature
RH57*
Recommend Temp (Fridge) : 37 °F (or 3 °C )
The fridge temperature can be set between 34°F
and 44°F (or between 1°C and 7°C) to suit your
particular needs.
Press the Fridge button repeatedly until the desired
temperature is shown in the temperature display.
The temperature will change by 1°F (or 1°C) with
each press. See below.
Fahrenheit : 37°F 36°F 35°F 34°F
44°F 43°F 42°F 41°F 40°F 39°F
38°F 37°F.
Centigrade : 3°C 2°C 1°C 7°C 6°C
5°C 4°C 3°C.
The temperature control process for the Fridge
works just like the Freezer process.
Press the Fridge button to set your desired
temperature.
After a few seconds, the Fridge will begin adjusting
towards the newly set temperature.
This will be reflected in the digital display.
• The temperature of the Freezer or Fridge
may rise when you open the doors too
frequently, or if a large amount of warm
or hot food is placed inside.
• This may cause the digital display to blink.
Once the Freezer and Fridge temperatures
return to their normal set temperatures, the
blinking will stop.
• If the blinking continues, you may need to “reset”
the Refrigerator.
Try unplugging the appliance, wait for around
10 minutes, and then plug the power cord back
in.
DA68-03015R-06.indb 35 2017. 7. 7. �� 10:01
English - 36
USING THE COLD WATER
DISPENSER
Push the appropriate ice type button
to select what you want dispensed.
NO ICE
Select this if you want to
turn ice maker o
Using the ice lever (1)
Push the Ice lever dispenser gently with your (1)
glass.
Ice will be released from the dispenser.
You can choose the type of ice by pushing the
cubed or crushed button first.
Using the Water lever (2)
Push the Water lever dispenser gently with (2)
your glass.
Water will be released from the dispenser.
Even if you push the water and Ice lever
at about the same time, the dispenser
operates only the option you actually
selected or pushed first.
Please wait 1 second before removing
the cup after dispensing water to prevent
spills.
Do not pull out the lever dispenser after
dispensing ice or water.
It comes back automatically.
Using the Ice & Water Dispenser together
To get Ice and water, push the Ice lever first (1)
for ice, then move your glass down and press the
water dispenser lever for water.(2)
Please wait 2 seconds before removing
the glass under the dispenser to prevent
spills.
If the Refrigerator door opens, the
Dispenser does not work.
• Do not pull the lever out.
You could damage or break the lever’s spring.
• To clean the ice bin/bucket, wash with a mild
detergent, rinse well, and dry thoroughly it.
Do not use harsh or abrasive cleaners or
solvents.
• In case ice doesn’t come out, pull out the ice
bucket and press the test button located on the
right side of ice maker.
• Do not press the test button continuously when
the tray is filled with ice or water.
Water may overflow or ice may jam the bucket.
• When you press the Test button, you will
hear the refrigerator chime (ding-dong).
When the chime sounds, release the Test
button.
• The chime sounds automatically again to let you
know the ice maker is working well.
If a power failure occurs, ice cubes may
melt then freeze together when the power
comes back on, causing the dispenser to
be out of order.
To prevent this problem, after a power
failure, pull out the ice bucket and discard
the residual ice or water.
CAUTION
CAUTION
DA68-03015R-06.indb 36 2017. 7. 7. �� 10:01
English - 37
OPERATING
After you dump the ice from the ice bucket,
you should press the dispenser lever once
with the ‘ICE CUBED’ or ‘CRUSHED’
function ON.
The ice maker will make new ice faster after you
return the ice bucket to the refrigerator.
• Do not put your fingers, hands, or any
unsuitable objects in the chute or ice-
maker bucket.
- This can cause personal injury or material
damage.
• Use only the ice maker provided with the
refrigerator.
• The water line to this refrigerator must be
installed / connected by a suitably qualified
person and must be connected to a potable
water supply.
• The ice maker requires water pressure of
20-125psi (138~862kPa) to operate properly.
• If you are going on a long vacation or
business trip and won’t be using the
water or ice dispensers for that period
of time, close the water valve to prevent
leaks.
• If you have not used the Ice maker for a while,
or you have opened the Freezer door frequently,
the Ice may stick together.
If this occurs, empty the ice bucket or break up
the ice with a wood kitchen tool.
Do not use sharp items such as knives or forks.
• When you remove the ice bucket, there may still
be some residual ice in the ice maker.
The ice maker may eject this ice into the freezer.
CAUTION
WARNING
CAUTION
Using the ice Dispenser
Press the Ice button to select the type of ice you
want.
Place your cup under the ice outlet, and then push
gently against the dispenser pad.
Make sure the glass is in line with the dispenser to
prevent the ice from bouncing out.
If you select Cubed Ice after using the Crushed Ice
feature, a small amount of residual crushed ice
might be produced.
Ice Cover
Ic tte
• If ice does not dispense, pull out the
icemaker cover and press test button
located on the ice maker.
• Do not press the test button continuously when
the tray is filled with ice or water.
Water may overflow or the ice may jam the
icemaker or dispenser.
Test button
CAUTION
DA68-03015R-06.indb 37 2017. 7. 7. �� 10:01
English - 38
For more space, you can store food with
Guard FRE-UPP instead of the ice bucket,
and remove the COVER-ICE MAKER and
Snack Bin.
If you remove the ice bucket, ICE OFF will
blink on the display panel.
Furthermore, you can remove the freezer
Upper drawer.
Since it does not aect thermal and
mechanical characteristics.
A declared storage volume of frozen
food storage compartment is calculated
with “Guard FRE-UPP” positioned and
“COVER-ICE MAKER”, “Snack Bin”, “Upper
Drawer” removed.
GUARD FRE (Freezer)-UPP (Optional)
Ice-M er
Ic tI
Shelf
Upper drawer
SMART ECO FEATURES
Smart Eco System
Keep freshness of food using 4 sensors according
to the operating environment, usage pattern and
the refrigerator operating status while saving
electricity costs.
Outside Humidity
Sensor
Outside Temperature
Sensor
Internal Temperature Sensors
DA68-03015R-06.indb 38 2017. 7. 7. �� 10:01
English - 39
OPERATING
FRIDGE MULTI-PURPOSE DOOR
BIN
A detachable divider makes it convenient to store
food.
Food products can be stored by items.
• Put the divider in place when storing slim-size
condiment bottles and canned drinks together.
• Take out the divider when storing carton-size
milks or drinks.
How to use the divider
1. Insert the divider as shown in the diagram to
compartmentalize the case.
2. When not in use, simply ip it around and move
it out of the way as shown in the diagram.
How to use the multi supporter
1. When not in use, leave the Multi Supporter
ipped over as shown in the diagram.
2. Flip the Multi Supporter to position 1 to prevent
items from falling out and over.
1
3. Flip the Multi Supporter to position 2 to use it as
a divider.
2
DA68-03015R-06.indb 39 2017. 7. 7. �� 10:01
English - 40
REMOVING THE REFRIGERATOR
ACCESSORIES
1. Shelves (Freezer/Fridge)
• Open the door completely and then lift up the
shelf as you pull it out to remove it.
(1)
• If you are unable to open the door completely,
pull out the shelf, lift it up, and turn it to remove
it.
(2)
(3)
Be careful not to insert the shelf upside
down.
Glass containers can scratch the surface
of the glass shelves.
2. Door Bin
• Remove the Door Bin by holding the door bin
with both hands and then gently lift it up.
CAUTION
3. Drawer
• Remove the Drawer by pulling it out and lifting it
up slightly.
4. Vegetable Bin/Dry Bin Cover
• Take out the bin above the Vegetable Bin
(refrigerator)/Dry Bin (freezer).
• Press down on the clips on either side of the
Vegetable Bin (refrigerator)/Dry Bin (freezer) and
pull them out towards you to remove the bin.
(Optional)
5. Vegetable Bin/Dry Bin
• Before taking out the Vegetable Bin/Dry
Bin, you need to remove the multipurpose
compartments from the door.
• Lift the bin up slightly as you pull it out.
DA68-03015R-06.indb 40 2017. 7. 7. �� 10:01
English - 41
OPERATING
6. Ice Bucket (Freezer)
• Remove the Icemaker Bucket by lifting it up and
pulling it out slowly.
• Grip the handle as shown in the gure.
• Remove the Ice Bucket slowly to prevent
damage.
Do not use excessive force when removing
the drawer cover.
You can break the cover and cause injury.
Before removing any accessories, make
sure that no food is in the way.
When possible, remove the food altogether
to reduce the risk of accidents.
7. Removing the Deodorizer
• Pull out the shelf slightly and then pull out the
unit while pushing the deodorizer cover clip up
using a athead screwdriver.
8. Cleaning the Deodorizer
• Clean the deodorizer once every two years
or whenever you feel its performance has
diminished.
• Dry the deodorizer under the sun for 24 hours
and then replace it in the reverse order of its
removal.
CLEANING THE REFRIGERATOR
• Do not use benzene, thinner, Clorox, or
car detergent to clean the refrigerator.
They can damage the surface of the
appliance and may cause a re.
• Do not spray the refrigerator with water while it
is plugged in.
This can cause an electric shock.
To clean the refrigerator, follow these steps:
1. Unplug the power code of the refrigerator.
2. Slightly dampen a soft lint-free cloth or paper
towel with water.
Do not use any kind of detergent to clean
the refrigerator because that can discolour
or damage the refrigerator.
3. Wipe the inside and outside of refrigerator until
it is clean and dry.
4. Plug the power cord of the refrigerator back in.
CHANGING THE INTERIOR
LIGHTS
Freezer / Fridge LED Lamp
• If the LED Lamp Cover is stained with foreign
substances, the LED lamp may not look bright.
Wipe the surface cover with clean dry cloth to
return the light to full brightness.
Do not disassemble or replace the LED
lighting yourself.
To replace the LED lights, contact a
Samsung service centre or your authorized
Samsung dealer.
If you attempt to replace the LED lamps
yourself, you risk subjecting yourself to an
electric shock or serious personal injury.
WARNING
CAUTION
DA68-03015R-06.indb 41 2017. 7. 7. �� 10:01
English - 43
OPERATING
4. Turn the new water
filter 90˚ clockwise.
5. Press the “Lighting / °C↔°F (3 sec)” button ( )
for about 3 seconds to reset the water filter.
The color of indicator changes from red to light
o.
A newly installed water filter cartridge may
cause water to briefly spurt from the water
dispenser.
This is due to air getting into the line.
It should pose no problem to operation.
When you replace the water filter, water
can drip from the bottom front of the
refrigerator.
Make sure to clean up any drips or spills
after you have changed the filter.
Removing residual matter inside the water
supply line after installing a new filter
1. Press the Water button, and then push the
Dispenser Lever with a cup or glass.
2. Flush 1 gallon of water through the filter, one
cup or glass at a time.
(Flush approximately 6 minutes.)
This will clean the water supply system and
remove air from the lines.
- Additional flushing may be required in some
households.
3. Open the refrigerator door and make sure there
are no water leaks coming from the water filter.
CAUTION
Reverse Osmosis Water Supply
IMPORTANT :
The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet
valve of the refrigerator needs to be between 35
and 120psi (241 and 827 kPa).
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to
be a minimum of 40 to 60psi (276 to 414kPa.)
If the water pressure to the reverse osmosis system
is less than 40 to 60psi (276 to 414kPa):
• Check to see whether the sediment filter in the
reverse osmosis system is blocked.
Replace the filter if necessary.
• Allow the storage tank on the reverse osmosis
system to refill after heavy usage.
• If your refrigerator has a water filter, it may
further reduce the water pressure when used
in conjunction with a reverse osmosis system.
Remove the water filter.
If you have questions about your water pressure,
call a licensed, qualified plumber.
Ordering replacement filters
To order more water filter cartridges, contact your
authorized Samsung dealer.
DA68-03015R-06.indb 43 2017. 7. 7. �� 10:01
English - 44
USING THE ICE MAKER
(OPTIONAL)
• To Remove the Ice Bucket.
- Hold the handle as shown in figure1.
- Lift up and pull the Bucket out slowly.
- Take out Ice Bucket out slowly to prevent
damage.
- When you reinstall the ice bucket, press and
hold the ICE button for 6 seconds.
• Normal Operation
- Any sounds you hear when the ice maker
dumps ice into the bucket are part of normal
operation.
- Ice may clump in the bucket if you do not
dispense ice for long periods of time.
If this occurs, remove all the ice and empty the
bucket.
- If ice does not come out, check for any ice
stuck in the chute and remove it.
- The first batch of ice cubes after installation
may be small because air has entered the water
line. Any air will be purged during normal use.
• When ICE OFF blinks on the display
panel, reinsert the ice bucket and/or
make sure it’s installed properly.
• When the door is open, the Ice and water
dispenser do not work.
• If you close the door hard, it may cause water
to spill over the ice maker.
• To prevent the ice bucket from dropping, use
both hands when removing it.
• To prevent injury, be sure to clean up any ice or
water that may have dropped on the floor.
• Do not let the children hang on the ice
dispenser or on the bucket.
They may get hurt.
• Be sure not to put your hand or any object into
the ice chute.
It may cause personal injury or damage
mechanical parts.
• Use care when storing food in plastic bags in
the freezer.
Incorrectly stored bags can get caught in the
ice bucket’s Auger Motor and prevent the
refrigerator from dispensing ice or cause the
freezer door to open unexpectedly.
CAUTION
DA68-03015R-06.indb 44 2017. 7. 7. �� 10:01
English - 45
TROUBLESHOOTING
Troubleshooting
PROBLEM SOLUTION
The refrigerator
does not work at
all or it does not
chill suciently.
• Check that the power plug is properly connected.
• Is the temperature control on the display panel set to the correct
temperature?
Try setting it to a lower temperature.
• Is the refrigerator in direct sunlight or located too near a heat source?
• Is the back of the refrigerator too close to the wall and therefore keeping air
from circulating?
The food in the
fridge is frozen.
• Is the temperature control on the display panel set to the correct
temperature?
Try setting it to a warmer temperature.
• Is the temperature in the room very low?
• Did you store the food with a high water content in the coldest part of the
fridge?
You hear unusual
noise or sounds.
• Check that the refrigerator is level and stable.
• Is the back of the refrigerator too close to the wall and therefore keeping air
from circulating?
• Was anything dropped behind or under the refrigerator?
• If you hear a “ticking” sound from inside the refrigerator, this is normal.
It occurs because various parts contract or expand in response to
temperature changes in the refrigerator interior.
The front corners
of the appliance
are hot and
condensation is
occurring.
• Some heat is normal as anti-condensators are installed in the front corners
of the refrigerator to prevent condensation.
• Is the refrigerator door ajar?
Condensation can occur when you leave the door open for a long time.
• Water condensation in a drawer may occur if the drawer contains
vegetables.
The condensation will dissipate naturally as time passes.
Ice is not
dispensing.
• Did you wait for 12 hours after installation of the water supply line before
making ice?
• Is the water line connected and the shut-o valve open?
• Did you manually stop the ice making function?
Make sure Ice is set to Cubed or Crushed.
• Are there any ice clumps in the ice maker bucket? Remove them.
• Is the freezer temperature too warm? Try setting the freezer temperature
lower.
You can hear water
bubbling in the
refrigerator.
• This is normal.
The bubbling comes from the refrigerant coolant liquid circulating through
the refrigerator.
There is a bad
smell in the
refrigerator.
• Has a food item spoiled?
• Make sure that strong smelling food (for example, fish) is wrapped so that it
is airtight.
• Clean out your freezer periodically and throw away any spoiled or suspect
food.
DA68-03015R-06.indb 45 2017. 7. 7. �� 10:01
English - 46
PROBLEM SOLUTION
Frost forms on the
walls of the freezer.
• Is the air vent blocked?
Remove any obstructions so air can circulate freely.
• Allow sucient space between the foods stored for ecient air circulation.
• Is the freezer door closed properly?
The water
dispenser is not
functioning.
• Is the water line connected and the shut-o valve open?
• Has the water supply line tubing been crushed or kinked?
Make sure the tubing is free and clear of any obstruction.
• Is the water tank frozen because the refrigerator temperature is too low?
Try selecting a warmer setting on the main display panel.
What can be done
when freezer door
is not closed well.
• Push lever dispenser and check water supply.
• Push lever dispenser (Ice mode) and check operation of auger motor.
• Remove objects on shelves that might obstruct drive auger.
Precautions : If you have not dispensed the water or ice for an extended
time, the ice bucket may accumulate ice chunk that interferes with the drive
auger, causing the inability to dispense.
Remove the remaining ice of bucket and object that might obstruct drive
Auger.
Please operate dispenser (water & ice) and it will improve auto-closing of
freezer door.
DA68-03015R-06.indb 46 2017. 7. 7. �� 10:01
冰箱
使用者手冊
想像無限可能
感謝您購買此 Samsung 產品。
獨立式電器
DA68-03015R-06.indb 1 2017. 7. 7. �� 10:01
繁體中文 - 2
安全資訊
• 在使用本冰箱之前，請通讀
此手冊並將其存放在冰箱附
近的一個安全位置，以備將
來參考。
• 僅按照本說明手冊中描述的
用途使用此冰箱。
本冰箱不適合供下列人士 (包
括小孩) 使用：身體官能或心
智能力退化者，或是經驗與
使用知識缺乏者。
他們需要有負責其安全的人
員在旁看護，或指示產品的
使用方法，方可使用。
• 8 歲以上的兒童以及身體官
能或心智能力退化者或是經
驗與使用知識缺乏者，可以
在有人對其進行看護或提供
相關安全使用指導並且瞭解
所涉及的危險的情況下使用
本設備。
兒童不得玩耍本設備。
兒童在沒有看護的情況下不
得清潔與維護本設備。
• 本手冊中的「警告和重要安
全指示」並未涵蓋所有可能
出現的狀況和情形。
在安裝、維護和使用本冰箱
時，您要遵從常識、警告和
安全資訊
目錄
安全資訊 …………………………………………………………………………………… 2
設定冰箱 ……………………………………………………………………………………15
操作 SAMSUNG 冰箱 …………………………………………………………………29
疑難排解 ……………………………………………………………………………………45
DA68-03015R-06.indb 2 2017. 7. 7. �� 10:01
繁體中文 - 3
安全資訊
注意事項，並為自己的行為
負責。
• 因為以下操作說明適用於各
種不同的型號，因此您冰箱
的特性可能與本手冊中所述
之特性略有不同，並且不是
所有警告標誌均可適用。
如果您有任何疑問或問題，
請與離您最近的服務中心聯
絡或到
www.samsung.com 網站上
尋求線上幫助和資訊。
重要的安全符號與注意事項：
警告
危險或不安全的操作可
能導致嚴重的人身傷害
或死亡。
注意
危險或不安全的操作可
能導致輕微的人身傷害
或財產損壞。
請勿嘗試。
請勿拆裝。
請勿觸摸。
遵照要求謹慎操作。
從牆壁式插座上拔下電
源插頭。
確保設備接地以防止觸
電。
致電聯絡中心以尋求幫
助。
注意：
這些警告標誌用於防止您和其
他人受到傷害。
請仔細閱讀它們。
閱讀本部分之後，請將其妥善
保管，以備將來參考。
DA68-03015R-06.indb 3 2017. 7. 7. �� 10:01
繁體中文 - 4
有關運輸和選址的嚴重
警告標誌
• 在運輸和安裝本設備
時，請小心搬運以免損
壞冷凍迴路的任何部
件。
• 使用 R-600a 或 R-134a 作
為冷媒。
檢查冰箱後面的壓縮機標籤
或冰箱內的銘版，以查看您
冰箱使用哪種冷媒。
• 如果本產品包含易燃氣體
(R-600a 冷媒)，
- 從製冷管中洩漏出的冷媒可
能著火或造成眼睛受傷。
如果發現洩漏，請避免使用
任何明火或潛在的火源，並
使冰箱所在的室內通風數分
鐘。
- 如果冷凍迴路發生洩漏，請
避免產生可燃氣體-空氣的混
合物，安裝冰箱的室內空間
需求取決於所用的冷媒量。
- 切勿在有任何損壞跡象的情
警告 況下啟動冰箱。 若有任何疑
問，請諮詢您的經銷商。
安裝冰箱的室內空間可按此
方式計算：冰箱內每 8 克
R-600a 冷媒需要 1 立方米
的空間。
在冰箱內部的標示牌上會標
示冰箱的冷媒量。
• 從製冷管中噴出的冷媒可能
著火或造成眼睛受傷。
如果有冷媒從製冷管中洩
漏，請避免使用任何明火，
移走冰箱附近的任何易燃
物，並立即通風。
- 否則，可能會導致火災或爆
炸。
- 如果冰箱包含異丁烷冷媒
(R-600a)，這是一種與環境
高度相容的天然氣體，但也
是易燃的。
在運輸和安裝冰箱時，請小
心搬運以免損壞冷凍迴路的
任何部件。
DA68-03015R-06.indb 4 2017. 7. 7. �� 10:01
繁體中文 - 5
安全資訊
有關安裝的嚴重警告標
誌
• 切勿將此設備安裝在潮
濕、油膩、灰塵滿布的
位置，以及直接暴露在
陽光下和有水 (雨滴) 的
位置。
- 電氣部件的絕緣層損壞可能
引起觸電或火災。
• 切勿將本冰箱置於陽光直射
之下，或暴露於火爐、室內
取暖器或其他設備的熱源之
下。
• 切勿將多個設備連接到同一
個多功能電源板上。
本冰箱應該始終連接到具有
與標牌上的額定電壓相符的
自帶獨立電源插座上。
- 此插座可提供最佳效能，並
可防止室內佈線電路過載，
以免過熱線路引起火災危
險。
如果牆壁式插座鬆動，請勿
插入電源插頭。
警告
- 否則，會有引起觸電或火災
的危險。
• 切勿使用中間或末端出現破
裂或損壞的電源線。
• 切勿過度彎折電源線或在上
面放置重物。
• 切勿在本冰箱附近使用煙霧
劑。
- 在冰箱附近使用煙霧劑可能
引起爆炸或火災。
• 切勿將此設備安裝在可能發
生氣體洩漏的位置。
- 否則可能會導致觸電或引起
火災。
• 建議由合格的技術人員
或維修公司來安裝此設
備或進行其他任何維修
服務。
- 否則，可能會導致觸電、火
災、爆炸、產品故障或人身
傷害。
• 在使用本冰箱之前，必須按
照此手冊前述內容選擇適當
DA68-03015R-06.indb 5 2017. 7. 7. �� 10:01
繁體中文 - 6
位置進行正確安裝。
• 將電源插頭連接到適當的位
置，使電源線下垂。
- 如果您顛倒連接電源插頭，
則電源線可能被切斷並引起
火災或觸電。
• 確保電源插頭不會被冰箱背
面擠扁或損壞。
• 在移動本冰箱時，小心不要
碾壓或損壞電源線。
- 否則會有引起火災的危險。
• 本冰箱必須安置到適當的位
置，以便在安裝後可以連接
到電源插座。
• 本冰箱必須接地。
- 您必須將冰箱接地以防止任
何因冰箱電流洩漏引起的功
耗洩漏或觸電。
• 切勿利用煤氣管、電話線或
其他電位避雷針接地。
- 錯誤使用接地插頭可能導致
觸電。
• 如果電源線損壞，請立
即讓製造商或其服務代
理進行更換。
• 冰箱上的保險絲必須由合格
的技術人員或維修公司進行
更換。
- 否則，可能會導致觸電或造
成人身傷害。
DA68-03015R-06.indb 6 2017. 7. 7. �� 10:01
繁體中文 - 13
安全資訊
其他正確使用提醒
• 如果停電，請致電當地的電
力公司並瞭解將停電多長時
間。
- 大多數停電故障將在一兩個
小時內得到解決，因此將不
會影響冰箱的溫度。
但是，您應該在停電期間儘
量減少打開冰箱門的次數。
- 如果停電超過 24 個小時，
請取出所有凍結的食物。
• 如果冰箱配備了鑰匙，請將
鑰匙放在兒童無法觸及並且
遠離冰箱的地方。
• 如果冰箱所在地點的溫度長
期低於為冷凍冰箱設計的溫
度範圍的最低溫度，則冰箱
可能無法始終正常運作 (可能
是由於冰箱內的溫度變得過
熱)。
• 請勿儲藏在低溫下容易腐壞
的食物，例如香蕉、甜瓜。
• 您的設備是無霜型，這表示
您無需手動除霜，它會自動
進行除霜。
• 除霜期間的溫度升高符合
ISO 要求。
但如果您要防止凍結食物在
設備除霜期間溫度過度升
高，請使用報紙多層包裹凍
結食物。
• 凍結食物在除霜期間的任何
溫度升高都會縮短其儲藏期
限。
DA68-03015R-06.indb 13 2017. 7. 7. �� 10:01
繁體中文 - 15
設定
準備安裝冰箱
恭喜您購買此 Samsung 冰箱。
希望您能樂享此款新冰箱提供的眾多先進功能和
高效體驗。
選擇安裝冰箱的最佳位置
• 選擇一個供應水方便的位置。
• 選擇一個沒有陽光直射的位置。
• 選擇一個地面平坦 (或接近平坦) 的位置。
• 選擇一個具有足夠空間以方便打開冰箱門的位
置。
• 選擇一個在冰箱的左、右、上、後側均有足夠
的空間以便空氣流通的位置。
• 選擇一個在冰箱需要維護或維修時可方便移動
的位置。
• 請勿將冰箱安裝到溫度高於 43 °C 或低於 5 °C
的地方。
AA
BB
CCDD
EE
深度 “A” 718 mm
寬度 “B” 912 mm
高度 “C” 1742 mm
總體高度 “D” 1774 mm
深度 “E” 721 mm
1725 mm 468 mm
165°165°
50 mm
912 mm
610 mm
1170 mm
34 mm
31 mm
每個測量值都是基於設計尺寸而得出，因
此可能會由於測量方法而不同。
設定冰箱
DA68-03015R-06.indb 15 2017. 7. 7. �� 10:01
繁體中文 - 16
移動冰箱時
為防止損壞地面，請確保前水平支腳處於較高位
置 (地面以上)。
請參閱手冊中的「如何校平冰箱」(第 21 頁)。
地面
為保證合適的安裝，您必須將冰箱放置在硬質
的、與地面其餘位置位於同一水平高度的平坦地
面上。
該表面應該強固到足以支持一個滿載的冰箱。
為了保護地板的磨光面，可將紙板箱剪開成一平
面，並置於要放置冰箱的位置。
在移動冰箱時，必須筆直向外拉出冰箱或筆直推
回原位。
請勿從一側向另一側來回擺動。
所需工具 (未提供)
十字螺絲起子 (+) 平頭螺絲起子 (-)
套頭扳手 (10 毫米)
內六角扳手 (5 毫米)
設定冰箱
您的新冰箱現在已安裝到位，可以開始設定並享
用該冰箱的各種功能。
完成下列所有步驟後，冰箱應該可以正常使用。
如果仍無法正常使用，請檢查電源或嘗試按照本
使用者手冊後面的疑難排解部分的內容進行操
作。
如果您有任何其他問題，請與 Samsung
Electronics 服務中心聯絡。
1. 將冰箱安裝到適當的位置，使冰箱與牆壁之間
保持一定的間隙。
請參閱本手冊中的安裝說明。
2. 如果冰箱已連接電源，請確保內部照明燈會在
您打開冰箱門時亮起。
3. 將溫度控制設定為最低溫度並等待約 1 個小
時。
冷凍室將基本冷卻，電機運行平穩。
4. 在啟動冰箱之後，它將需要數小時才能達到適
當的溫度。
如果冰箱溫度已經足夠低，您即可在冰箱內儲
藏食物和飲料。
5. 安裝完成之後，推壓分配器推杆以檢查出水或
出冰是否正常。
6. 請確保冰箱前面比後面高出 0.6 度角。
DA68-03015R-06.indb 16 2017. 7. 7. �� 10:01
繁體中文 - 17
設定
設定冰箱門
如果進門口無法讓冰箱順利通過，可以先卸下冰
箱門。
分離冰箱供水管
1. 向前拖出兩根水管 (位於固定器內)。
2. 透過按壓聯結器 ( ) 並分離水管 ( ) 卸下兩根12
水管 (白色水管用於飲水機，另一根用於製冰機)。
請確保水管顏色正
確匹配。
( 1 )
( 2 )
注意
在重新連接供水管時，請確保相同顏色的
水管插在一起。
重新安裝供水管
1. 水管必須完全插入透明聯結器的中心位置，以
防從飲水機漏水。
2. 將 2 個卡子插到安裝接頭處，並檢查各個卡子
是否牢固地卡住水管。
注意
透明聯結器的中心位置
卡子 A (1/4 英寸)
(6.35 毫米)
請勿切割水管。
輕輕地將水管從聯結器分離。
將卡子放在兒童無法觸及的地方，並確保
兒童不會玩耍它們或將其放到嘴裡。
拆卸冷凍室門
1. 斷開電源線連接，然後使用十字螺絲起子卸下
頂蓋上的 2 顆螺釘 ( )。 1
然後打開冰箱門並拖動兩側的掛鉤以鬆開頂蓋
( 2 )。
向上抬起並向懷裡拖動頂蓋以將其分離 ( 3 )。
-拆卸鉸鏈蓋時要保持冰箱門打開，卸下鉸鏈蓋
之後再關閉冰箱門。
( 1 )
( 3 )( 2 )
視型號而定，上部鉸鏈蓋可能是一個整
體，也可能是分開的。
注意
DA68-03015R-06.indb 17 2017. 7. 7. �� 10:01

Produkt Specifikationer

Mærke: Samsung
Kategori: Køleskab
Model: RH60H90203L

Har du brug for hjælp?

Hvis du har brug for hjælp til Samsung RH60H90203L stil et spørgsmål nedenfor, og andre brugere vil svare dig


Køleskab Samsung Manualer

Samsung

Samsung SRL4200B Manual

10 Februar 2025
Samsung

Samsung SRL4200S Manual

10 Februar 2025
Samsung

Samsung RS29GRS Manual

5 Februar 2025
Samsung

Samsung RS23HKMR Manual

5 Februar 2025
Samsung

Samsung RT331MASW Manual

5 Februar 2025
Samsung

Samsung RT30VC Manual

5 Februar 2025
Samsung

Samsung RT32GTSW Manual

5 Februar 2025
Samsung

Samsung RT27SABP Manual

5 Februar 2025
Samsung

Samsung RT25SCSW Manual

5 Februar 2025
Samsung

Samsung RT25SAAS Manual

5 Februar 2025

Køleskab Manualer

Nyeste Køleskab Manualer

Siemens

Siemens KF96DPPEA Manual

1 April 2025
Summit

Summit FF6W7BZADA Manual

28 Marts 2025
DeLonghi

DeLonghi DEWC155D Manual

26 Marts 2025
DeLonghi

DeLonghi DEWC46D Manual

26 Marts 2025
Whirlpool

Whirlpool ARG 746/A+/5 Manual

25 Marts 2025
Bosch

Bosch KTR15NWEAG Manual

22 Marts 2025
Caple

Caple RBL6 Manual

21 Marts 2025
FrigeluX

FrigeluX CBNF177BI Manual

20 Marts 2025
Café

Café CWE19SP2NS1 Manual

16 Marts 2025
Bosch

Bosch B36FD30ENS Manual

15 Marts 2025