Sedona L600CART Manual


Læs nedenfor 📖 manual på dansk for Sedona L600CART (3 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/3
Assembly Instructions:
SEDONA L400CART
L500CART
& L600CART
Lynx Freestanding Cart
Model L400CART, L500CART &L600CART
Lynx Grills, Inc., 6023 E. Bandini Blvd. Commerce, CA 90040 Ph
Document 33807 Rev C 02/08/13
Step 1.
Step 2.
Step 3.
Step 1.
Aer opening and idenfying the components, select the back
panel assembly and either the right or le side panel assembly.
Orient the parts as shown in the illustraon for . step 1
Note that these parts are upside down with the shelves at the
oor. Hook the right or le side to the back into the four keyways
located on the edge. When aached all four keyways should be
engaged and the back and side ush to the top.
Repeat this step for the opposite side panel.
Step 2.
With the cart oriented upside down, locate the 4 - #8 screws and
nuts and mount the electrical transformer to the access plate
shown in the illustraon for this step. It may be done at the end of
the assembly but is somewhat easier to access at this stage.
Step 3.
Refer to the gure for and insert the base assembly into the step 3
cavity at the back corners of the cabinet. Check that the tank hole
is posioned as shown and the magnet is located on the open side.
Splay the two sides out slightly and enclose them over the front of
the base. The sides and back have pockets that t over the casters
for clearance. Use 4 of the ¼-20 x ½ screw at each corner to lock
the assembly in place.
Access
Plate
magnet
tank
hole
Screw
4 places
Introducon:
Your Freestanding Cart comes with all of the components necessary
to assemble a cart for the SEDONA Series of Lynx Grills.
The SEDONA CART series is comprised of 8 sub assemblies:
1. Back Panel Assembly
2. Right Side Panel Assembly with Shelf
3. Le Side Panel Assembly with Shelf
4. Base Assembly with Wheels
5. Inner Shelf Assembly
6. Cross Brace Assembly
7. Right Door
8. Le Door
In addion there are 14 screws (1/4 -20 x ½) to assemble the
cart and grill and 4 screws with nuts (#8-32 x 3/8) to aach the
transformer assembly supplied with the Grill.


Produkt Specifikationer

Mærke: Sedona
Kategori: Ikke kategoriseret
Model: L600CART

Har du brug for hjælp?

Hvis du har brug for hjælp til Sedona L600CART stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Sedona Manualer

Sedona

Sedona VC600F Manual

26 December 2024
Sedona

Sedona L500F-NG Manual

29 August 2024
Sedona

Sedona L500F-LP Manual

29 August 2024
Sedona

Sedona L1500LP Manual

29 August 2024
Sedona

Sedona LIJ600 Manual

29 August 2024
Sedona

Sedona VC30ADA Manual

29 August 2024
Sedona

Sedona L1600NG Manual

29 August 2024
Sedona

Sedona L700CART Manual

29 August 2024
Sedona

Sedona L700PSFR NG Manual

29 August 2024
Sedona

Sedona L2500LP Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer