Shimano SG-C6060-8C Manual


Læs nedenfor 📖 manual på dansk for Shimano SG-C6060-8C (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
Internal Geared Hub
IMPORTANT NOTICE
Contact the place of purchase or a distributor for information on
installation, adjustment, and replacement of the products which are not
found in the user's manual. A dealer's manual for professional and
experienced bicycle mechanics is available on our website (https://si.
shimano.com).
For safety, be sure to read this “user's manual”
thoroughly before use, follow it for correct use, and
store it so that it can be referenced at any time.
The following instructions must be observed at all times in order to
prevent personal injury and physical damage to equipment and
surroundings. The instructions are classified according to the degree of
danger or damage which may occur if the product is used incorrectly.
DANGER Failure to follow the instructions will result
in death or serious injury.
WARNING Failure to follow the instructions could
result in death or serious injury.
CAUTION
Failure to follow the instructions could
cause personal injury or physical damage
to equipment and surroundings.
Important Safety Information
WARNING
Because each bicycle may handle slightly differently depending on the
model, be sure to learn the proper braking technique (including brake
lever pressure and bicycle control characteristics) and operation of your
bicycle. Improper use of your bicycle's brake system may result in a loss
of control or a fall, which could lead to severe injury.
Do not disassemble or modify the product. This may cause the product
to not operate correctly, and you may suddenly fall and be seriously
injured.
Check that the wheels are fastened securely before riding the bicycle.
Otherwise, you may fall and be seriously injured.
CAUTION
Be sure to shift the shifting lever one gear at a time (one or two gears
at a time for an 11-speed hub). During shifting, reduce the force being
applied to the pedals. If you try to force operation of the shifting lever
or suddenly perform shifting while the pedals are being turned strongly,
your feet may come off the pedals and the bicycle may fall over, which
could result in serious injury. Using the shifting lever to suddenly shift
may also cause the outer casing to spring out of the shifting lever. This
does not affect the capabilities of the shifting lever because the outer
casing returns to the original position after shifting.
Do not continuously apply the brakes when riding down long slopes.
For coaster brakes or roller brakes, this will cause the internal brake
parts to become very hot, weakening braking performance, as well as
causing a reduction in the amount of brake grease inside the brake,
which can lead to noise being generated or problems such as
abnormally sudden braking. For hydraulic disc brakes, it may cause a
sudden increase in the brake lever stroke, preventing the brakes from
operating and resulting in serious injury.
Spin the wheel and check the braking force of the brake.
Do not touch the area around the brake for at least 30 minutes after
riding the bicycle. If the brake is used frequently, the area around the
brake may become hot.
Coaster brake section Roller brake section Disc brake section
Notice
A noise is generated by the gear-shifting structure in the internal
geared hub. If you experience an abnormal noise, either consult with
the place of purchase or refer to the dealer's manual.
Maintenance for an 11-speed hub
1. The oil port screw on the hub shell is used to replace oil. Never
loosen it unless you are replacing oil. Oil could leak and spray.
2. In order to maintain proper performance, it is recommended that
you contact the place of purchase or a distributor to carry out
maintenance such as internal oil replacement after riding 1,000 km
from the start of use and then after about once every year (or once
about every 2,000 km if the bicycle is used very frequently). If the
bicycle is used under harsh conditions, more frequent maintenance
is required.
Maintenance for other hubs
1. To maintain the product in good working order, it is recommended
to have the place of purchase or nearest Pro shop carry out
maintenance such as lubrication of the internal parts about once
every year from the first time of use (once about every 2,000 km if
the bicycle is used very frequently). If the bicycle is used under
harsh conditions, more frequent maintenance is required. Also, for
carrying out maintenance, the use of SHIMANO internal geared
hub grease or a lubrication kit is recommended. If SHIMANO grease
or a SHIMANO lubrication kit is not used, problems such as a
malfunction in gear shifting may occur.
The internal geared hub is not completely waterproof. Avoid using the
hub in places where water might get inside and do not use high-
pressure water to clean the hub, otherwise the internal mechanism may
rust.
The gears should be periodically washed with a neutral detergent. In
addition, cleaning the chain with neutral detergent and lubricating it
can be an effective way of extending the life of the gears and the chain.
If chain skipping has started occurring, replace the gears and the chain
at a place of purchase or a distributor.
Never place your foot on the bell crank. Otherwise, gear shifting may
not function properly.
As you shift gears, stop pedaling or reduce the force being applied to
the pedals. This will ensure smooth gear shifting. In addition, a loud
sound may be temporarily emitted if the gears are shifted while
strongly pedaling with E-BIKE, etc., but this is normal.
Practice gear shifting until you become familiar with the operation.
Products are not guaranteed against natural wear and deterioration
from normal use and aging.
For maximum performance we highly recommend SHIMANO lubricants
and maintenance products.
Regular Inspections Before Riding the Bicycle
Before riding the bicycle, check the following items. If any problems are
found, consult your place of purchase or a distributor.
Is gear shifting carried out smoothly?
Is there any noticeable damage to the electric wires?
Do any abnormal noises occur during operation?
Names of parts
The components differ according to the specifications of the internal
geared hub.
DI2
Cassette joint type
Internal geared hub
Cassette joint
Internal geared hub
Yellow setting lines
Bell crank
Bell crank
Bell crank cover
End of hub axle
Bell crank type Bell crank type (SM-3R40)
Line on push rod
UM-3FJ0A-002 User's manual
Please note: specifications are subject to change for improvement without notice. (English)
© May. 2020 by SHIMANO INC. ITP
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
High Tech Campus 92, 5656 AG Eindhoven, The Netherlands Phone: +31-402-612222
3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan


Produkt Specifikationer

Mærke: Shimano
Kategori: Ikke kategoriseret
Model: SG-C6060-8C

Har du brug for hjælp?

Hvis du har brug for hjælp til Shimano SG-C6060-8C stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Shimano Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024