Smeg PVS750 Manual

Smeg Komfur PVS750

Læs nedenfor 📖 manual på dansk for Smeg PVS750 (18 sider) i kategorien Komfur. Denne guide var nyttig for 71 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/18

Contents

1. Precautions for safety and use________________________ 22

2. Fitting the appliance in the top ________________________ 23

2.1 Fixing to the supporting structure _______________________________________23

2.2 Fitting the adhesive foam rubber strip____________________________________24

2.3 Fitting the fixing clips ________________________________________________24

2.4 Fitting the hob into the hole in the work-top _______________________________25

3. Electrical connection _______________________________ 26

4. Gas connection ___________________________________ 27

4.1 Bottled gas connection _______________________________________________27

4.2 Room ventilation____________________________________________________27

4.3 Combustion gas discharge ____________________________________________27

5. Adapting to different types of gas______________________ 28

5.1 Removing the hob skin _______________________________________________28

5.2 Adjusting for bottled gas ______________________________________________29

5.3 Adjusting for natural gas______________________________________________29

5.4 Adjusting the primary air flow __________________________________________30

5.5 Reassembling the hob skin____________________________________________31

5.6 Adjusting the minimum setting for natural ga ______________________________31

5.7 Adjusting the minimum for bottled gas ___________________________________31

5.8 Hob burner layout ___________________________________________________31

5.9 Greasing the gas taps________________________________________________31

6. Description of contro

ls ______________________________ 32

6.1 The front panel _____________________________________________________32

7. Using the hob _____________________________________ 33

7.1 Fitting the pan stands ________________________________________________33

7.2 Lighting burners with safety device______________________________________36

7.3 Practical hints for using the burners _____________________________________36

7.4 Pan diameters______________________________________________________36

Cleaning and maintenance ____________________________ 37

7.5 Cleaning the hob____________________________________________________37

7.6 Cleaning instructiona for an acid-et ched glass hob _________________________37

7.7 Cleaning the components _____________________________________________37

THESE INSTRUCTIONS ONLY APPLY TO THE COUNTRIES OF DESTINATION WHOSE

IDENTIFICATION SYMBOLS ARE LISTED ON THE COVER OF THIS MANUAL.

THIS BUILT-IN HOB IS CLASSIFIED AS CLASS 3.

INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified

engineer who is to check the gas supply system and install, commission and test the

appliance.

INSTRUCTIONS FOR THE USER: these provide recommendations for use, a

description of the controls and the correct procedures for cleaning and maintaining the

appliance.

Precautions for Safety and Use

1. Precautions for safety and use

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT

TO HAND THROUGHOUT THE HOB'S LIFE CYCLE. USERS ARE ADVISED TO READ THIS MANUAL

AND ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE HOB. ALSO KEEP THE SET OF

NOZZLES PROVIDED IN A SAFE PLACE. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED

STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS APPLIANCE IS INTENDED FOR

HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE. THE

APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION: COOKING AND HEATING FOODS;

ALL OTHER USES ARE TO BE CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN THOSE STATED ABOVE.

NEVER LEAVE PACKAGING RESIDUES UNATTENDED IN THE HOME. SEPARATE WASTE

PACKAGING MATERIALS BY TYPE AND CONSIGN THEM TO THE NEAREST SEPARATE DISPOSAL

CENTRE.

THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH ELECTRICAL SYSTEM

SAFETY REGULATIONS.

THE PLUG TO BE CONNECTED TO THE POWER SUPPLY LEAD AND THE RELATIVE SOCKET MUST

BE OF THE SAME TYPE AND COMPLY WITH THE RELEVANT REGULATIONS.

THE POWER SUPPLY SOCKET MUST BE ACCESSIBLE EVEN AFTER THE APPLIANCE HAS BEEN

BUILT-IN.

NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD.

IMMEDIATELY AFTER INSTALLATION, CARRY OUT A QUICK TEST ON THE HOB FOLLOWING THE

INSTRUCTIONS PROVIDED LATER IN THIS MANUAL. IF THE APPLIANCE FAILS TO OPERATE,

DISCONNECT IT FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE

CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.

AFTER EACH USE OF THE HOB, ALWAYS CHECK THAT THE CONTROL KNOBS ARE TURNED TO

"ZERO" (OFF).

NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT AND SMOOTH ON THE

HOB PAN STANDS.

NEVER USE PANS OR GRIDDLE PLATES WHICH PROJECT BEYOND THE OUTSIDE EDGE OF THE

HOB.

THE NAMEPLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND MARK IS IN A VISIBLE

POSITION UNDERNEATH THE CASING, ANNEXED TO THIS MANUAL AND APPLIED TO THE QUALITY

CERTIFICATE.

THIS NAMEPLATE MUST NEVER BE REMOVED.

THE APPLIANCE IS INTENDED FOR USE BY ADULTS. KEEP CHILDREN AT A SAFE DISTANCE AND

NEVER ALLOW THEM TO PLAY WITH IT.

THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL

AND ELECTRONIC EQUIPMENT (WEEE).

THIS DIRECTIVE CONTAINS THE REGULATIONS GOVERNING THE COLLECTION AND RECYCLING

OF DECOMMISSIONED APPLIANCES THROUGHOUT THE EUROPEAN UNION.

The manufacturer declines all responsibility for injury or damage caused by failure to comply

with the above regulations or deriving from tampering with even just one part of the appliance

and the use of non-original spare parts.

Instructions for the Installer

2. Fitting the appliance in the top

If the hob has to be adapted for a type of gas different from the one for which it

is preset in the factory, make this adjusting before building it into the unit,

following the instructions in point “5. Adapting to different types of gas”.

The procedures required below must be carried out by a skilled builder and/or joiner.

The hob can be installed on various materials, including masonry, metal, solid wood

and wood finished with plastic laminates, provided the material is heat-resistant

(T 90° C).

2.1 Fixing to the supporting structure

Make a hole in the cabinet top with the dimensions shown here, maintaining a

distance of at least 50 mm from the rear edge. This appliance may be installed

against walls higher than the worktop surface, provided the distance shown here is

maintained, in order to prevent damage due to overheating. Make sure that there is at

least 750 mm

between the hob burners and a shelf

or hood (if any) placed vertically

above them.

If the hob is installed above an oven, the oven must be fitted with a cooling fan.

If the hob is installed above a cupboard with doors, a separator panel must be

installed underneath it. Leave a gap of at least 10 mm between the bottom of the hob

and the surface of the panel, which must be easily removable to allow sufficient

access for any servicing procedures.

Instructions for the Installer

2.2 Fitting the adhesive foam rubber strip

Fit the adhesive foam rubber strip

(supplied with the hob) around the

outside edge of its surround.

It will act as a cushion between

the surface of the surround and

that of the cabinet. The diagram

on the right shows the correct

position for the foam rubber strip.

Take great care when fitting it to

ensure that it does not project

beyond the outside edge of the

frame.

2.3 Fitting the fixing clips

Fit the fixing clips in all the points

marked with an arrow. The clips

fix the hob an ensure that it is

centred correctly.

To fit the clips to the hob, simply

press them gently horizontally into

the groove provided (fig. A).

Then turn them upwards to fix

them permanently in place (fig. B).

Instructions for the Installer

2.4 Fitting the hob into the hole in the work-top

Take special care when fitting the hob into the work-top. If the procedures are not

carried out correctly, exactly as described, the hob may be damaged.

Before fitting the hob, remove

the pan stands (if fitted) and the

burners from the hob.

When fitting the hob, first rest the

surround entirely on the back

edge of the hole in the work-top.

Do not apply leverage to the

surround; since this part is very

delicate there is a risk of

damaging it.

Then lower the front of the hob

until the appliance is completely in

place.

Instructions for the Installer

3. Electrical connection

Check that the power supply line voltage and size are as specified on the nameplate

underneath the appliance's casing. This nameplate must never be removed.

The plug on the end of the power supply lead and the wall socket must be of the same

type and comply with the relevant regulations. Check that the power supply line is

properly earthed.

Pass the power supply cable through the rear of the cabinet, taking care that it does not

touch the bottom case of the hob, or the oven (if any) built in underneath it.

The appliance's power supply line must be fitted with an omnipolar breaking device with

contact gap of at least 3 mm, located in an easily accessible position close to the

appliance itself.

The use of reductions, adapters or junctions is not recommended.

If the power supply cable has to be replaced, the gauge of the wires in the new cable must

be at least 0.75 mm2 (3 x 0.75 cable), bearing in mind that the earth wire (yellow-green)

must be at least 20 mm longer at the end for connection to the appliance. Use only a type

H05V2V2-F or similar cable resistant to a temperature of up to 90°C. The cable must be

replaced by a qualified electrician, who must make the mains connection as shown below.

L = brown

N = blue

= yellow-green

The power supply lead must be replaced by an authorised service centre to prevent all

risks.

The manufacturer declines all responsibility for injury or damage caused by failure to

comply with the above regulations or deriving from tampering with even just one part

of the appliance.

Instructions for the Installer

4. Gas connection

If the appliance is installed above an oven, the gas hose must be passed around the back

of the oven to prevent overheating.

The connection to the gas mains may be made using a copper pipe or a continuous-wall

steel hose in accordance with the relevant regulations. To simplify connection, the

horizontal position of the fitting A on the back of the appliance is adjustable. Undo the

hexagonal nut B, turn the fitting A into the required position and re-tighten the hexagonal

nut B (it has a rubber gasket to ensure it provides an effective seal). When installation is

complete, check for any leaks with a soapy solution, never with a naked light. The

appliance is tested with G20 (2H) natural gas at the pressure of 20 mbar. For use with

other types of gas, see point "5. ADAPTING TO DIFFERENT TYPES OF GAS". The gas

intake connection has an external ½” gas thread (ISO 228-1).

Connection with copper pipe: The connection to the gas

supply mains must be made so that no stresses or strains

of any kind are applied to the appliance. The connection

can be made using the adapter unit D with two conical

elements, always fitting the gasket C supplied.

Connection with steel hose: use only continuous-wall

stainless steel hoses compliant with the relevant

regulations, and always fit the gasket C supplied between

the fitting A

and the hose

When connecting with a hose, ensure that the total length of the pipeline is not more

than 2 metres; also ensure that the hoses do not touch moving parts and are not

crushed.

4.1 Bottled gas connection

Use a pressure regulator and make the connection to the gas cylinder in accordance

with the relevant regulations. Make sure that the gas supply pressure is as stated in

the table in point "5.2 Adjusting for bottled gas".

4.2 Room ventilation

The appliance may only be installed in a permanently ventilated room as specified by

the relevant regulations. The air flow into the room where the appliance is installed

must be sufficient for proper gas combustion and room ventilation. The air intakes,

protected by gratings, must be of suitable size (see relevant regulations) and located

so that they cannot be even partially obstructed.

The kitchen must be kept properly ventilated to disperse the heat and humidity

produced by cooking processes: in particular, a window should be opened or the

speed of any fans increased after prolonged use.

4.3 Combustion gas discharge

Combustion gases must be discharged by means of hoods connected to a flue with

reliable natural draught, or a fan extraction system. An effective extraction system

requires careful design by an authorised specialist, and must comply with the

regulation distances and positions. After installation, the engineer must issue a

certificate of compliance.

Instructions for the Installer

5. Adapting to different types of gas

The operations described below must be carried out with the appliance not

built-in and not connected to the gas or electricity supply.

The appliance is tested with G20 (2H) natural gas at the pressure of 20 mbar.

If it is to be used with other types of gas, the burner nozzles have to be changed

and the primary air flow adjusted.

To replace the nozzles and adjust the burners, the hob skin has to be removed.

Proceed as described below.

5.1 Removing the hob skin

Remove all the burner components in the numerical order shown below:

• Pull off all the knobs.

• Lift all the burner

components off the hob.

• Remove the cover plate

of each burner by

undoing the screws.

• Remove the hob skin

fixing screws, taking care

only to remove the

screws shown on the

right.

• After removing all the

components described

above, lift off the hob

skin.

Instructions for the Installer

5.2 Adjusting for bottled gas

Undo the screw C and push the air regulator

D fully down.

Remove the nozzle with a 7 mm spanner E

and fit the suitable one, following the

instructions in the tables referring to the type

of gas to be used. The nozzle must not be

tightened with a torque of more than 3 Nm.

Regulate the air flow by sliding the regulator D

along until the distance “ ” stated in point "5.5 X

Adjusting the primary air flow” is obtained.

Fix the regulator D

by tightening the screw

Burner

Rated

heat

capacity

(kW)

Bottled gas – G30/G31 30/37 mbar

Nozzle

diameter

1/100 mm

By-pass

1/100

Reduced

heat

capacity

(W)

Flow

rate g/h

G30

Flow

rate g/h

G31

Auxiliary 1.05 48 30 400 76 75

Semi rapid 1.7 62 32 450 124 121

Rapid 3.0

82 1050 218 214 50

Ultra Rapid 5.0 108 63 1600 363 357

5.3 Adjusting for natural gas

The appliance is tested with G20 (2H) natural gas at the pressure of 20 mbar. To return the

appliance to the condition required to use this type of gas, proceed as described in point “5.2

Adjusting for bottled gas” but select the nozzles and adjust the primary air flow for natural gas,

as indicated in the table below and in point “5.5 Adjusting the primary air flow”.

Rated heat

Burner Capacity (kW) Natural gas - G20 20 mbar

Nozzle diameter Reduced heat capacity

1/100 mm (W)

Auxiliary 1.05 73 400

Semi rapid 1.7 92 450

Rapid 3.0 123 1050

Ultra Rapid 5.0 165 1400

Instructions for the Installer

5.4 Adjusting the primary air flow

Refers to the gap “X” in mm.

BURNER G20

20 mbar

G30/G31

30/37 mbar

0.5 9.5

Auxiliary

Semi rapid 1 1

2 3

Rapid

Ultra Rapid open 4

To identify the burners on your hob, refer to the drawings in point “5.8 Hob burner

layout”.

Instructions for the Installer

5.5 Reassembling the hob skin

Reverse the procedure described in point “5.1 Removing the hob skin”.

When replacing the cover plates, check that the seals are fitted correctly.

7.1Fit the pan stands as described in point Fitting the pan stands.

5.6 Adjusting the minimum setting for natural ga

Reassemble the components on the burner and fit the

knobs onto the tap rods.

Light the burner and turn it to the minimum setting.

Remove the knob again and adjust the regulator

screw inside or beside the tap rod (depending on the

model) until an even minimum flame is obtained.

Put the knob back in place and check the stability of

the burner flame (the flame must not go out when the

knob is turned quickly from the maximum to the

minimum setting).

5.7 Adjusting the minimum for bottled gas

To adjust the minimum level when using bottled gas, the adjuster screw inside or

beside the tap rod must be turned fully clockwise (depending on the models).

The diameters of the bypasses for each individual burner are stated in point “5.2

Adjusting for bottled gas".

After adjusting for use of a gas other than the gas used for testing the appliance,

replace the label on the casing with the label for the new gas. The label is supplied in

the bag with the LPG nozzles (G30 - G31).

5.8 Hob burner layout

Burner type

1 Auxiliary

2 Semi rapid

3 Rapid

4 Ultra rapid

5.9 Greasing the gas taps

Over time, the gas taps may become stiff or jam. Clean their insides and change their

lubricating grease. This operation must be carried out by a skilled technician.

Instructions for the User

6. Description of controls

6.1 The front panel

All the hob's control and monitoring devices are placed together on the front panel.

CONTROL AREA

5 Burner Hob

KNOB OPERATING MODE

To light the flame, press the knob and at the same time turn it anti-clockwise to

the minimum flame symbol .

To adjust the flame, turn the knob to the zone between the maximum and the

minimum settings.

To turn off the burner, turn the knob back to the O position.

BURNER LAYOUT - Key to symbols

Front left-hand burner

Rear left-hand burner Middle burner

Rear right-hand burner Front right-hand burner

Instructions for the User

7. Using the hob

Check that the fixing cover plates E, the

burners, the flame diffuser rings and the pan

stands are fitted correctly.

The projections A on the flame diffuser rings

must be fitted into the recesses B in the burner.

The holes C in the burner must mate with the

ignition plugs and thermocouples on the hob. D

7.1 Fitting the pan stands

The pan stands are supplied dismantled from the hob. To place each pan stand on its

burner correctly, follow the instructions provided below:

Each rack must be positioned on the corresponding burner in

order to guarantee proper operation.

Be very careful to match the different central diameters of the

racks to the flame-spreader crowns.

Produkt Specifikationer

Mærke:	Smeg
Kategori:	Komfur
Model:	PVS750
Bredde:	740 mm
Dybde:	56 mm
Højde:	510 mm
Produktfarve:	Sølv
Placering af apparat:	Indbygget
Komfurtype:	Gaskomfur
Overfladetype:	Glas
Antal kogeplader / madlavningsområde:	5
Blus/kogeplade zone 1 strøm:	1700 W
Blus/kogeplade zone 2 strøm:	1050 W
Blus/kogeplade zone 1 type:	Regelmæssig
Kogezone 1 form:	Rund
Blus/kogeplade zone 1 position:	Venstre bagende
Blus/kogeplade zone 1 strømkilde:	Gas
Blus/kogeplade zone 2 type:	Simre
Kogezone 2 form:	Rund
Blus/kogeplade zone 2 position:	Venstre front
Blus/kogeplade zone 2 strømkilde:	Gas
Blus/kogeplade zone 3 type:	Ekstra stor
Blus/kogeplade zone 4 type:	Stor
Blus/kogeplade zone 4 strømkilde:	Gas
Kogezone 4 form:	Rund
Blus/kogeplade zone 3 strømkilde:	Gas
Kogezone 3 form:	Rund
Blus/kogeplade zone 3 position:	Central
Blus/kogeplade zone 4 position:	Højre bagende
Dimensioner på installationsrummet (BxDxH):	733 x 56 x 503 mm
Blus/kogeplade zone 5 position:	Højre forside
Blus/kogeplade zone 5 strømkilde:	Gas
Antal gasbrændere:	5
Blus/kogeplade zone 5 type:	Regelmæssig
Blus/kogeplade zone 4 strøm:	3000 W
Blus/kogeplade zone 5 strøm:	1700 W
Blus/kogeplade zone 3 strøm:	5000 W
Kogezone 5 form:	Rund
Elektronisk tænding:	Ja
Simre kogeplade / madlavningsområde:	3100 W
Almindelige kogeplade / madlavningsområde:	1050 W
Stor kogeplade / madlavningsområde:	1700 W
Wokbrænder:	Ja
Ekstra stor hurtig kogeplade / madlavningsområde:	5000 W
Wokbrændeposition:	Midten