Sonic Alert HA360VB 2.1 Manual

Sonic Alert Beveiliging HA360VB 2.1

Læs nedenfor 📖 manual på dansk for Sonic Alert HA360VB 2.1 (1 sider) i kategorien Beveiliging. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
The HomeAware Vibe is a new accessory that connects to the
HomeAware main unit, transmitters, and receivers. This
personal pager will alert you to events like the smoke/CO
detector, the baby crying, the phone ringing and many more.
The HomeAware Vibe will alert you with multiple colored LED
lights, vibration and an audio alert, all patterned to a specific
alert. Simply clip the HomeAware Vibe to your waistband or slip
it into a pocket and enjoy the freedom of never missing an alert
again. In fact the HA360VB1.2 can also act as an emergency
alert notification device in case you have fallen or have another
emergency you need help with. By simply pushing the PAGE
button on the front of the unit it will send an alert notification to
all your HomeAware receivers and the main unit. Because it is
portable and the increased range due to the HomeAware’s mesh
network, you will be safe throughout your house and out.
HA360VB2.1 Features
Emergency alert button when help is needed. Ultra-high
brightness strobe for maximum visibility.
Clips easily on waistband and small enough to slip into a
pocket.
Connects to the HomeAware main unit, transmitters, and
receivers.
Alert patterns unique to you, vibrate, sound, flashing lights, or
different colors for different alerts.
Battery Features
Note: After you have received your HomeAware Vibe, please
fully charge before first use. A complete charge will take
approximately 3 hours.
Green charge complete
1 Red light battery low
2 Red Lights Battery half charged
If the Vibe is switched to Off the battery indicators lights will not
be lit but the Vibe is still charging.
Low Battery Check
The Vibe will alert you when the battery is getting low.
Depending on what switch or switches that are on, it will be a
single yellow blink, vibration or beep.
TO LINK THE HOMEAWARE VIBE WITH THE HA360MVSB
Linking:
Press SET UP button on the main unit and the word LINK will
be shown on the display, press ENTER. LINK will begin
blinking.
Press and hold down the PAGE button on the front of Vibe,
PICK DEVICE will be shown on display of the main unit. Press
the blue MINUTE/down arrow button until the display reads
HELP, then press ENTER. DONE will be shown on the display
when linking is completed.
Switch / Page Button Controls
There are several ways that the Vibe can be set to notify you of
alerts happening in or around your home. Pick one, two or all four
with a flip of a switch.
V - Vibrate
S - Sound
F - Flash
CColor
Door - Green
BabyBlue
PhoneOrange
Smoke/CO – Red
Cyan Universal
Low Battery Single Yellow blinking light
Lost Link Double Yellow blinking light
PAGE Button / Emergency Help
When the PAGE button on the front of the HomeAware Vibe is held
down for 3 seconds, it sends a HELP alert to the main unit.
If the Vibe and the Main Unit have lost connection, it will need to
be reset
Push all switches to the off position except for the On/Off power
switch leave in the on position.
Press and hold the PAGE button, the LED light will be a moving
purple.
Reset is completed when the LED light is a solid orange.
The Vibe is now ready to be linked to the Main Unit.
HA360VB2.1 – Quick Start Guide


Produkt Specifikationer

Mærke: Sonic Alert
Kategori: Beveiliging
Model: HA360VB 2.1

Har du brug for hjælp?

Hvis du har brug for hjælp til Sonic Alert HA360VB 2.1 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Beveiliging Sonic Alert Manualer

Beveiliging Manualer

Nyeste Beveiliging Manualer