StarTech.com IMC1GSFP60W Manual


Læs nedenfor 📖 manual på dansk for StarTech.com IMC1GSFP60W (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: June 2, 2020 2:48 PM
Product Diagram (IMC1GSFP60W)
Component Function
1PWR LED
An external is Green: DC Power Source
detected.
An external is not O: DC Power Source
detected.
2RJ45 Port
Connect a to the Network Device Media
Converter.
A (PD) is detected.ON: PoE Powered Device
The is Flashing: Media Converter
transmitting/receiving data.
3DIP Switch
DIP1: This switch is currently not in use.
DIP 2:
Sets SFP speeds to 1000Mbps (default) O:
Sets SFP speeds to 100Mbps.On:
4SFP LED
Indicates that a link is detected on the Green:
SFP.
Indicates that data is being Flashing:
transmitted or received.
5SFP Slot Connect an (100/1000BASE-X) to the SFP
Media Converter.
64-Pin Terminal Block
Connect an external (48-56V DC Power Source
DC Input) to the .Media Converter
Connect an alarm or warning circuit to the
relay (ALM) connection. The relay is triggered if
the loses power.Media Converter
Industrial RJ45 to Open SFP Mini PoE Media Converter | 1000 Mbps (1G) | 60W
7Ground Screw
Connect a ground connection to the Ground
Screw DC Power Source when connecting a to
the .Media Converter
Requirements
For the latest requirements, please visit www.startech.com/IMC1GSFP60W
Network Equipment (e.g. Router, Network Switch) x 1
MSA-Compliant 100/1000BASE-X SFP Transceiver Module x 1
RJ45 Terminated UTP/STP CAT5e (or better) Network Cable x 1
Terminated Fiber Optic Cable (dependent on SFP Module) x 1
DC Power Source x 1
Small Flat Head Screwdriver x 1
Phillips Head Screwdriver x 1
Alarm or Warning Circuit x 1
Powering the Media Converter
Connecting and installing the must be completed by a 4-Wire Terminal Connector
licensed Electrician.
Notes: Make sure that you turn o the power source before connecting the power wire
to the .Media Converter
Do not exceed the recommend power source voltage as it may result in personal or
product damage.
1. Using a , loosen the two screws (+V-) on the Small Flat Head Screwdriver 4-Wire
Terminal Connector (included).
2. Connect the from a (48 - 56V DC), or the provided Power Wires DC Power Source
Barrel Power Connector Adapter Terminal Block Connectors to the proper on
the . The terminals are marked on the Media Converter Media Converter’s Casing
(connect the positive wire to V+ and the negative wire to V-).
3. (Optional) Using a , loosen the two screws (ALM) on Small Flat Head Screwdriver
the .4-Wire Terminal Connector
4. (Optional) Connect the from an or to the Relay Wires Alarm Warning Circuit 2
ALM Relay Pins Terminal Block Connector on the .
5. Tighten the four screws on the .4-Wire Terminal Connector
6. Insert the in the on the 4-Wire Terminal Connector 4-Wire Terminal Block Media
Converter.
1 2 3 5 6 7
4


Produkt Specifikationer

Mærke: StarTech.com
Kategori: Ikke kategoriseret
Model: IMC1GSFP60W

Har du brug for hjælp?

Hvis du har brug for hjælp til StarTech.com IMC1GSFP60W stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret StarTech.com Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024