Sungrow SH10RT Manual


Læs nedenfor 📖 manual på dansk for Sungrow SH10RT (164 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 42 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/164
User Manual
3–Phase Hybrid Inverter
SH5.0RT/SH6.0RT/SH8.0RT/SH10RT/SH5.0RT-20/
SH6.0RT-20/SH8.0RT-20/SH10RT-20
SH5.0–10RT&SH5.0–10RT-20-UEN-Ver21-202309
I
All Rights Reserved
All Rights Reserved
No part of this document can be reproduced in any form or by any means without the prior
written permission of Sungrow Power Supply Co., Ltd (hereinafter "SUNGROW").
Trademarks
and other Sungrow trademarks used in this manual are owned by
SUNGROW.
All other trademarks or registered trademarks mentioned in this manual are owned by their
respective owners.
Software Licenses
It is prohibited to use data contained in firmware or software developed by SUNGROW,
in part or in full, for commercial purposes by any means.
It is prohibited to perform reverse engineering, cracking, or any other operations that
compromise the original program design of the software developed by SUNGROW.
II
About This Manual
The manual mainly contains the product information, as well as guidelines for installation,
operation, and maintenance. The manual does not include complete information about the
photovoltaic (PV) system. Readers can get additional information at www.sungrowpower.
com or on the webpage of the respective component manufacturer.
Validity
This manual is valid for the following model of low-power grid-connected PV string inverters:
• SH5.0RT
• SH6.0RT
• SH8.0RT
• SH10RT
• SH5.0RT-20
• SH6.0RT-20
• SH8.0RT-20
• SH10RT-20
It will be referred to as "inverter" hereinafter unless otherwise specified.
Target Group
This manual is intended for professional technicians who are responsible for installation, op-
eration, and maintenance of inverters, and users who need to check inverter parameters.
The inverter must only be installed by professional technicians. The professional technician
is required to meet the following requirements:
Know electronic, electrical wiring and mechanical expertise, and be familiar with electri-
cal and mechanical schematics.
Have received professional training related to the installation and commissioning of elec-
trical equipment.
Be able to quickly respond to hazards or emergencies that occur during installation and
commissioning.
Be familiar with local standards and relevant safety regulations of electrical systems.
Read this manual thoroughly and understand the safety instructions related to
operations.
How to Use This Manual
Please read this manual carefully before using the product and keep it properly at a place
for easy access.
All contents, pictures, marks, and symbols in this manual are owned by SUNGROW. No part
of this document may be reprinted by the non-internal staff of SUNGROW without written
authorization.
III
Contents of this manual may be periodically updated or revised, and the actual product pur-
chased shall prevail. Users can obtain the latest manual from support.sungrowpower.com
or sales channels.
Symbols
This manual contains important safety instructions, which are highlighted with the following
symbols, to ensure personal and property safety during usage, or to help optimize the prod-
uct performance in an efficient way.
Please carefully understand the meaning of these warning symbols to better use the manual.
Indicates high-risk potential hazards that, if not avoided, may lead to death or seri-
ous injury.
Indicates moderate-risk potential hazards that, if not avoided, may lead to death or
serious injury.
Indicates low-risk potential hazards that, if not avoided, may lead to minor or mod-
erate injury.
Indicates potential risks that, if not avoided, may lead to device malfunctions or fi-
nancial losses.
“NOTE” indicates additional information, emphasized contents or tips that may be
helpful, e.g., to help you solve problems or save time.
VIII
8.9.1 Chart................................................................................................ 100
8.9.2 Fault Alarm Record ........................................................................... 101
8.9.3 Event Records .................................................................................. 102
8.10 Inverter (Optional)..................................................................................... 103
8.11 EV-Charger (Optional)............................................................................... 104
8.11.1 Driving Distance Per kWh.................................................................106
8.11.2 Charging Mode................................................................................106
8.11.3 Parameter Setting ........................................................................... 111
8.11.4 Start/Stop Switch............................................................................. 112
8.12 More........................................................................................................ 113
8.12.1 System Parameters......................................................................... 114
8.12.2 Running Time ................................................................................. 115
8.12.3 Fault Recovery................................................................................ 115
8.12.4 Regular Parameters ........................................................................ 116
8.12.5 Off-grid Parameters......................................................................... 116
8.12.6 Active Power Regulation.................................................................. 117
8.12.7 Reactive Power Regulation .............................................................. 117
8.12.8 Battery Discharge Time ................................................................... 118
8.12.9 Battery Forced Charge Time ............................................................ 119
8.12.10 Load Control ................................................................................. 120
8.12.11 Communication Parameters ........................................................... 121
8.12.12 Firmware Update........................................................................... 122
8.12.13 Grounding Detection...................................................................... 123
8.12.14 Parallel Configuration .................................................................... 123
8.12.15 Frequency Shift Power Control ....................................................... 124
8.12.16 Energy Management Mode ............................................................124
8.12.17 MicroGrid System Parameters........................................................ 125
8.12.18 DO Configuration .......................................................................... 127
9 System Decommissioning .......................................................................... 128
9.1 Decommissioning the Inverter .....................................................................128
9.1.1 Disconnecting Inverter....................................................................... 128
9.1.2 Dismantling the Inverter..................................................................... 128
9.1.3 Disposal of Inverter ...........................................................................129
9.2 Decommissioning the Battery ...................................................................... 129
10 Troubleshooting and Maintenance .......................................................... 131
10.1 Troubleshooting........................................................................................ 131
10.2 Maintenance ............................................................................................ 136
IX
10.2.1 Maintenance Notices ....................................................................... 136
10.2.2 Routine Maintenance....................................................................... 137
10.2.3 Replacing the Button Cell................................................................. 137
11 Appendix ...................................................................................................... 139
11.1 Technical Data .......................................................................................... 139
11.2 The Compatibility for Backup under Off-grid Scenario .................................. 150
11.3 Quality Assurance..................................................................................... 151
11.4 Contact Information................................................................................... 152
1
1Safety Instructions
When installing, commissioning, operating, and maintaining the product, strictly observe the
labels on the product and the safety requirements in the manual. Incorrect operation or work
may cause:
Injury or death to the operator or a third party.
Damage to the product and other properties.
Do not operate the product and cables (including but not limited to moving the
product, installing the product, operating the product and cables, powering up
the product, maintaining the product, and working at heights) in harsh weather
conditions such as flooding, lightning, rain, snow, and level 6 or stronger wind.
In case of fire, evacuate from the building or product area and call the fire alarm.
Re-entry into the burning area is strictly prohibited under any circumstances.
Tighten the screws with the specified torque using tools when fastening the
product and terminals. Otherwise, the product may be damaged. And the dam-
age caused is not covered by the warranty.
Learn how to use tools correctly before using them to avoid hurting people or
damaging the device.
Maintain the device with sufficient knowledge of this manual and use proper
tools.
The safety instructions in this manual are only supplements and cannot cover
all the precautions that should be followed. Perform operations considering ac-
tual onsite conditions.
SUNGROW shall not be held liable for any damage caused by violation of gen-
eral safety operation requirements, general safety standards, or any safety in-
struction in this manual.
When installing, operating, and maintaining the product, comply with local laws
and regulations. The safety precautions in this manual are only supplements
to local laws and regulations.
2
1.1 Unpacking and Inspection
Check all safety signs, warning labels and nameplates on devices.
The safety signs, warning labels and nameplates must be clearly visible and
cannot be removed or covered before the device is decommissioned.
After receiving the product, check whether the appearance and structural parts of
the device are damaged, and check whether the packing list is consistent with the
actual ordered product. If there are problems with the above inspection items, do
not install the device and contact your distributor first. If the problem persists, con-
tact SUNGROW in time.
1.2 Installation Safety
Make sure there is no electrical connection before installation.
Before drilling, avoid the water and electricity wiring in the wall.
Improper installation may cause personal injury!
If the product supports hoisting transport and is hoisted by hoisting tools, no
one is allowed to stay under the product.
When moving the product, be aware of the product weight and keep the balance
to prevent it from tilting or falling.
Before operating the product, must check and ensure that tools to be used have
been maintained regularly.
1 Safety Instructions User Manual
3
1.3 Electrical Connection Safety
Before electrical connections, please make sure that the inverter is not damaged,
otherwise it may cause danger!
Before electrical connections, please make sure that the inverter switch and all
switches connected to the inverter are set to "OFF", otherwise electric shock may
occur!
The PV string will generate lethal high voltage when exposed to sunlight.
Operators must wear proper personal protective equipment during electrical
connections.
Must ensure that cables are voltage-free with a measuring instrument before
touching DC cables.
Respect all safety instructions listed in relevant documents about PV strings.
Danger to life due to a high voltage inside the inverter!
Be sure to use special insulation tools during cable connections.
Note and observe the warning labels on the product, and perform operations
strictly following the safety instructions.
Respect all safety instructions listed in this manual and other pertinent
documents.
If the battery is short-circuited, the instantaneous current will be excessively high
and a large amount of energy will be released, which may cause fire and personal
injury.
Disconnect the battery from all voltage sources prior to performing any work on
the battery.
Lethal voltages are present at the battery terminals and cables connecting to the
inverter. Severe injuries or death may occur if the cables and terminals in the inver-
ter are touched.
Observe all safety information provided by the battery manufacturer.
User Manual 1 Safety Instructions
4
Damage to the product caused by incorrect wiring is not covered by the warranty.
Electrical connection must be performed by professionals.
Please use measuring devices with an appropriate range. Overvoltage can dam-
age the measuring device and cause personal injury.
All cables used in the PV generation system must be firmly attached, properly
insulated, and adequately dimensioned.
Do not damage the ground conductor. Do not operate the product in the ab-
sence of a properly installed ground conductor. Otherwise, it may cause per-
sonal injury or product damage.
Check the positive and negative polarity of the PV strings, and connect the PV con-
nectors to corresponding terminals only after ensuring polarity correctness.
During the installation and operation of the inverter, please ensure that the positive
or negative poles of PV strings do not short-circuit to the ground. Otherwise, an
AC or DC short-circuit may occur, resulting in equipment damage. The damage
caused by this is not covered by the warranty.
The interfaces of the battery in the system must be compatible with the inverter.
The entire battery voltage range must be completely within the permissible range
of the inverter, and the battery voltage shall not exceed the maximum permissible
DC input voltage of the inverter.
Comply with the safety instructions related to PV strings and the regulations re-
lated to the local grid.
Install the external protective grounding cable first when performing electrical
connection and remove the external protective grounding cable last when re-
moving the inverter.
1 Safety Instructions User Manual


Produkt Specifikationer

Mærke: Sungrow
Kategori: Ikke kategoriseret
Model: SH10RT

Har du brug for hjælp?

Hvis du har brug for hjælp til Sungrow SH10RT stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Sungrow Manualer

Sungrow

Sungrow SG320HX-20 Manual

23 Januar 2025
Sungrow

Sungrow SG5.0RS Manual

11 Januar 2025
Sungrow

Sungrow SG125HV Manual

11 Januar 2025
Sungrow

Sungrow PVS24MH Manual

11 Januar 2025
Sungrow

Sungrow SC5000UD-MV Manual

21 December 2024
Sungrow

Sungrow SR20D-M Manual

9 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer