Tascam US-1X2 Manual


Læs nedenfor 📖 manual på dansk for Tascam US-1X2 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 36 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
X
US-1x2
USB Audio Interface
OW N E R 'S MA N U AL
IMPORTANT SAFETY PRECAUTIONS
INFORMATION TO THE USER
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the in-
struction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures.
a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment and receiver.
c) Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
d) Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications to this equipment not expressly approved by TEAC
CORPORATION for compliance could void the user’s authority to operate this
equipment.
For U.S.A.
For Canada
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMERIQUE DE LA CLASSE B EST CONFORME A LA NORME
NMB-003 DU CANADA.
This product complies with the European Directives
request and the other Commission Regulations.
Declaration of Conformity
Model Number: US-1×2
Trade Name: TASCAM
Responsible party: TEAC AMERICA, INC.
Address: 1834 Gage Road, Montebello, California, U.S.A.
Telephone number: 1-323-726-0303
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
IMPORTANT SAFETY PRECAUTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or
the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
10
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand,
tripod, bracket, or table specified by the man-
ufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/
apparatus combination to avoid injury from
tip-over.
13 Unplug this apparatus during lightning storms or when unused for long
periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-sup-
ply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
o The apparatus draws nominal non-operating power from the AC out-
let with its POWER or STANDBY/ON switch not in the ON position.
o The mains plug is used as the disconnect device, the disconnect de-
vice shall remain readily operable.
o Caution should be taken when using earphones or headphones with
the product because excessive sound pressure (volume) from ear-
phones or headphones can cause hearing loss.
o If you are experiencing problems with this product, contact TEAC for a
service referral. Do not use the product until it has been repaired.
CAUTION
o Do not expose this apparatus to drips or splashes.
o Do not place any objects filled with liquids, such as vases, on the appa-
ratus.
o Do not install this apparatus in a confined space such as a book case or
similar unit.
o The apparatus should be located close enough to the AC outlet so that
you can easily grasp the power cord plug at any time.
o If the product uses batteries (including a battery pack or installed bat-
teries), they should not be exposed to sunshine, fire or excessive heat.
o CAUTION for products that use replaceable lithium batteries: there is
danger of explosion if a battery is replaced with an incorrect type of
battery. Replace only with the same or equivalent type.
o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE THE
ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.
o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT, CONTACT
THE STORE WHERE YOU PURCHASED THE UNIT FOR A SERVICE REFER-
RAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN REPAIRED.
o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCE-
DURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZ-
ARDOUS RADIATION EXPOSURE
8 For European Customers
Disposal of electrical and electronic equipment
(a) All electrical and electronic equipment should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
(b) By disposing of the electrical and electronic equipment correctly, you
will help save valuable resources and prevent any potential negative
effects on human health and the environment.
(c) Improper disposal of waste equipment can have serious effects on the
environment and human health as a result of the presence of hazardous
substances in electrical and electronic equipment.
(d) The crossed out wheeled dust bin
symbol indicates that electrical and electronic equipment
must be collected and disposed of separately from
household waste.
(e) The return and collection systems are available to the end
users. For more detailed information about disposal of old
electrical and electronic equipment, please contact your city office,
waste disposal service or the shop where you purchased the equipment.
Introduction
Thank you for your purchase of the TASCAM US-1x2 USB Audio Interface.
Before connecting and using this unit, please take time to read this manual
thoroughly to ensure you understand how to properly set it up and connect
it, as well as how to use its many useful and convenient functions. After you
have finished reading this manual, please keep it in a safe place for future
reference.
Should the contents of the memory of a connected device (including hard
disks and optical discs) in the same system as this unit be lost, our company
will bear no responsibility for repair, including for compensation.
Before connecting this unit to a computer, you must download and in-
stall a dedicated driver.
Included items
This product includes the following items.
Keep the packing materials for transportation in the future.
Please contact the store where you purchased this unit if any of these items
are missing or have been damaged during transportation.
0 Main unit x1 ............................................................................................................................
0 USB cable x1 ...........................................................................................................................
0 Set of DAW software installation guides................................................................ x1
0 Owner’s Manual (this document)
including warranty x1 .........................................................................................................
Note about the Reference Manual
This Owner's Manual explains the main functions of this unit. Please see the
Reference Manual for information about all the unit's functions.
You can also download this Owner's Manual and the Reference Manual from
the TEAC Global Site ( ).http://teac-global.com/
Precautions for placement and use
0 The operating temperature range of this unit is 5–35 °C.
0 Do not install this unit in the following types of locations. Doing so could
make the sound quality worse or cause malfunction.
Locations with frequent vibrations
Near windows or other places exposed to direct sunlight
Near heating equipment or in other locations that become very hot
Extremely cold places
Very humid or poorly ventilated locations
Very dusty locations
0 To enable good heat dissipation, do not place anything on top of the unit.
0 Do not place this unit on top of a power amplifier or other device that
generates heat.
Using the TEAC Global Site
You can download the Owner’s Manual necessary for this unit from the TEAC
Global Site ( ).http://teac-global.com/
1. Open the TEAC Global Site ( ).http://teac-global.com/
2. In the TASCAM Downloads section, click the desired language to open
the Downloads website page for that language.
NOTE
If the desired language does not appear, click Other Languages.
3. Click the product name in the “Search by Model Name” section to open
the Downloads page for that product.
4. Select and download the Owner’s Manual that are needed.
Beware of condensation
Condensation could occur if the unit is moved from a cold place to a warm
place, it is used immediately after a cold room has been heated or it is other-
wise exposed to a sudden temperature change.
To prevent this, or if this occurs, let the unit sit for one or two hours at the
new room temperature before using it.
Cleaning the unit
To clean the unit, wipe it gently with a soft dry cloth.
Do not wipe with chemical cleaning cloths, benzene, thinner, alcohol or other
chemical agents. Doing so could damage the surface or cause discoloration.
User registration
Customers in the USA, please visit the TASCAM website (http://tascam.com/)
to register as a user online.
Names and functions of parts
Front panel/Rear panel
5 6
1
7 9 0 q
2 43
8
ert y u i ow
front panel
rear panel
1 PHANTOM indicator
The indicator lights when the phantom power switch( ) of the rear pan-o
el is set to .ON
2 SIG indicators
The SIG indicators light green when signals (of at least −32 dBFS) are
input through the / / jacks ( / / ).IN1 IN2 LINE IN L-R 89u
3 PEAK indicators
The PEAK indicators light red when signals that are about to distort (−1
dBFS or higher) are input through the jacks (IN1/IN2/LINE IN L-R 89u/ / ).
4 GAIN knob
Use to adjust the input levels of the / jacks ( / ). IN1 IN2 8 9
5 LINE OUT knob
Use to adjust the output level of the jacks ( ).LINE OUT L-R i
6 PHONES knob
Use to adjust the output level of the jack ( ).PHONES q
CAUTION
Before connecting headphones, minimize the volume with the PHONES
knob. Failure to do so might cause sudden loud noises, which could harm
your hearing or result in other trouble.
7 USB indicator
This lights when the USB connection is working.
8 IN1 jacks
This mic level XLR jacks are balanced input jacks.
9 IN2 jacks
This input jacks are standard TRS jacks.
Use the switches ( ) on the front of the unit to enable bal-LINE/INST 0
anced line ( ) input or unbalanced ( ) input for the standard TRS LINE INST
jacks.
0 LINE/INST switches
Set according to the jack ( ) input sources.IN2 9
Set to when connecting electronic instruments, audio devices LINE
and similar equipment. Set to when connecting an electric guitar, INST
electric bass or other equipment with high output impedance.
q PHONES jack
Use this standard stereo phone jack to connect stereo headphones. Each
of these jacks outputs the same signal of the rear panel as the LINE OUT
L–R jacks( ). Use an adapter to connect headphones with a mini plug.i
w DC IN 5V connector (Micro USB type)
When connected to an iOS device or other equipment that cannot pow-
er this unit, you must use a USB power adapter, mobile battery or other
power supply. See “When using an iOS device” for details.
e Kensington Security Slot
r USB port (USB-B type)
Use the included USB cable to connect the unit to a computer or an iOS
device. (Supports USB 2.0)
t DIRECT MONITOR switch
Set this to when you want to monitor the input source directly. When ON
set to , you will be able to set the input source volume (Low/Mid /ON
High) using the Settings Panel application described below.
y INPUT SELECT switch
Set according to the input sources.
Set to FRONT when connecting to / jacks ( / ) of the front IN1 IN2 8 9
panel. Set to REAR when connecting to jacks ( ) of the rear LINE IN L-R u
panel.
u LINE IN L-R jacks
These RCA pin jacks are analog line inputs.
i LINE OUT L-R jacks
These RCA pin jacks are analog line inputs.
o Phantom power switch
Use this switch to provide phantom power to the jacks( ).+48V IN1 8
Installing the dedicated software
To use this unit, a dedicated software must be installed on a computer.
Download the latest dedicated software for the operating system you are
using from the TEAC Global Site ( ).http://teac-global.com/
0 On a Windows computer, this will install the Windows driver and Settings
Panel application.
0 Installing the dedicated software on a Mac will install only the Mac Set-
tings Panel application. The standard OS driver will be used.
0 With an iOS device, the standard OS driver will be used, so there is no
need to install any.
CAUTION
Before starting to install software, quit other applications.
Installing the Windows dedicated software
Follow the procedures below to install the Windows dedicated software.
CAUTION
i Complete installation of the Windows dedicated software on the comput-
er before connecting the unit to it with the USB cable.
i If you connected the unit to the computer using the USB cable before in-
stalling the Windows dedicated software and the “Found New Hardware
Wizard” launched, close the Wizard and disconnect the USB cable.
Windows dedicated software installation procedures
1. Download the latest Windows dedicated software for the operating sys-
tem you are using from the TEAC Global Site (http://teac-global.com/)
and save it on the computer to be used with the unit.
2. Uncompress the saved software (zip file) on the computer desktop or
another location.
3. Double-click the “TASCAM_US-1x2_Installer_x.xx.exe” file in the folder
that appears after uncompression to automatically launch the installa-
tion software.
4. When a or screens appears, “Security Warning” “User Account Control”
click the button.“Yes”
5. When the Setup Wizard screen appears, click the button.(Fig.A)“Next”
Read the contents of the License Agreement, and select “I accept the
agreement if you agree to the terms.
Then, click the “Next” button.(Fig.B)
e
(Fig.A) (Fig.B)
6. Next, click the button.(Fig.C)“Install”
Start installation.(Fig.D)
e
(Fig.C) (Fig.D)
7. The following screen appears when installation has completed. Click the
“Finish” button.
This quits the installer and launches the Windows Settings Panel.
NOTE
The first time you connect the unit by USB to the computer after installing
the software, installation of the device driver will be executed. Some
time might be necessary before the unit is recognized because Windows
Update will be automatically searched at this time. If the unit is still not
recognized after a while, open the software installation screen from the
notification area at the bottom right of the computer display, and click
“Skip obtaining driver software from Windows Update” to stop the search.
Installing the Mac dedicated software
NOTE
i Install the Mac dedicated software on the computer before connecting
the unit to it with the USB cable.
i Depending on the Gatekeeper setting, a warning message might appear
during installation. For information about Gatekeeper, see “Working with
Gatekeeper” “Installation” in of the Reference Manual.
Mac dedicated software installation procedures
1. Download the latest Mac dedicated software for the operating system
you are using from the TEAC Global Site ( ) and http://teac-global.com/
save it on the computer to be used with the unit.
2. Double-click “TASCAM_US-1x2_Installer_x.xx.dmg”, which is the saved
disk image file for the Mac dedicated software, and double-click “US-
1x2_Installer.pkg” inside the folder that opens.(Fig.A)
When the installer starts, click the button. (Fig.B)“Continue”
e
(Fig.A) (Fig.B)
NOTE
Depending on the computer’s settings, the downloaded zip file might not
have been uncompressed automatically. In this case, uncompress the zip
file first and then double-click the disk image file.
3. Next, select the desired language and click the button. (Fig.C)“Continue”
Click the button and check the contents of the Software “Read License”
License Agreement. If you agree to the contents of the license, click
“Agree”. (Fig.D)
e
(Fig.C) (Fig.D)
4. Next, click the button to start installation. (Fig.E)“Install”
The following screen appears when installation has completed. Click the
“Close” button. (Fig.F)
e
(Fig.E) (Fig.F)
Connecting the power
When using a computer (Windows/Mac)
Normally, when this unit is connected to a computer, it will operate using
USB bus power, so connecting a separate power supply device is not neces-
sary.
When using an iOS device
When this unit is connected to an iOS device, connecting an external battery,
USB power adapter or other power supply device is necessary in order to
power the unit.
Connect an AC adapter (TASAM PS-P520E), external battery pack (TASCAM
BP-6AA) or the genuine Apple USB power adapter included with the iPad/
iPhone to a USB cable (sold separately), and connect it to the DC IN 5V port
( ).w
CAUTION
i No USB power adapter is included with an iPod touch. To use it with an
iPod touch, purchase a genuine Apple USB power adapter (that can sup-
ply 5 V and a current of at least 700 mA) separately.
i Operation with other external battery packs and USB power adapters
is possible, but we strongly recommend using a TASCAM PS-P520E AC
adapter, TASCAM BP-6AA external battery pack or the genuine Apple USB
power adapter included with the iPad/iPhone.
When using another external battery pack or USB power adapter, be sure
that the power supply device meets the following specifications.
o Supplied voltage: 5 V
o Supplied current: 700 mA or more
Using a power supply device when the specifications are other than the
above could cause malfunction, overheating, fire or other problems. If
anything abnormal occurs, stop use and contact the retailer where you
purchased the unit or a TEAC service center to request repair.
Making various settings
Opening the Settings Panel
8 Windows
From under “All Apps” (All Programs), select “US-1x2 Settings Panel” “TAS-
CAM”.
The Windows Settings Panel has three pages. Click a tab at the top of the
Settings Panel to open that page.
Home: This page shows a variety of information and allows the selec-
tion of presets suitable for specific operations.
Settings: Make detailed settings for the US-1x2 on this page.
Custom: Make software mixer settings.
8 Mac
Select “US-1x2_SettingsPanel” from the Applications folder and launch it to
open the Mac Settings Panel on the computer display.
Making settings on the Home page (Windows only)
The Operating Mode setting can be set on the Home page of the Windows
Settings Panel.
Windows Settings Panel Home page
“DAW”
Use this setting when using DAW software, as well as when you do not
need “BROADCAST/KARAOKE” mode (for live broadcasting or karaoke
applications).
“BROADCAST/KARAOKE”
Use this setting for live broadcasting, karaoke and similar applications.
This preset enables the loopback function. It mixes the sound output from
the computer with the sounds of mics input through the IN1 IN2/ /LINE IN
L-R jacks ( / / ) on the unit and sends the mix back to the computer89u .
“TALKING
Use this setting for voice calling and similar applications.
This preset disables the loopback function.
The sound output from the computer (including received voices and mu-
sic playing on the computer) is not sent back to the computer.
“CUSTOM”
Use the settings made on the page.Custom
Making settings on the Settings page (Windows) /
Settings Panel (Mac)
Settings can be made on the page of the Windows Settings Panel or Settings
on the Mac Settings Panel.
Windows Settings Panel Settings page
Mac Settings Panel
1 Direct Monitor Settings IN 1-2
Set the monitoring signal for the / / jacks ( / / ) to IN1 IN2 LINE IN L-R 89u
Mono Stereo or .
2 Input Volume
Use this to adjust the monitoring balance between the input signals
from this unit’s input jacks and the output signals from the computer.
3 Audio Input ON
Turn input on/off for each input separately.
4 Buffer Size item (Windows only)
Set the size of the buffer used when audio input and output signals are
transferred to and from the computer.
For details about other settings, see “Windows Settings Panel overview” or
“Mac Settings Panel overview” “Using the Settings Panel” in of the Refer-
ence Manual.
Connecting other equipment
Example (front)
Guitar/Bass Guitar HeadphonesVocal mic
Example (back)
* Note: When using an iOS device, you must also connect an external battery
pack or USB power supply to assure power.
CD player
Powered speakers
Computer or iOS device
External battery pack
or USB power adapter
CAUTION
i Before making connections, turn this unit and all equipment to be con-
nected off (standby).
i The phantom power affects both input channels simultaneously. Do not
turn phantom power on when connecting a mic that does not require
phantom power.
i Set the phantom power switch to only when using a condenser +48V
microphone that requires phantom power.
i Turning phantom power when a dynamic mic or other mic that +48V
does not require it is connected could damage this unit and connected
equipment.
i Do not connect or disconnect mics while phantom power is on. Doing
so could cause a loud noise and might damage this unit and connected
equipment.
i Set the and knobs to their minimum values before LINE OUT PHONES
turning phantom power on/off. Depending on the connected mics, sud-
den loud noises from monitoring equipment could occur, and this could
damage the equipment or harm hearing.
i When using condenser mics that require phantom power and dynamic
mics together, be sure to use balanced dynamic mics. Unbalanced dy-
namic mics cannot be used when phantom power is enabled.
i Supplying phantom power to some ribbon mics will break them. If you
are unsure, do not supply phantom power to a ribbon mic.
Connecting with iOS devices
To connect an iOS device, you will need a Lightning to USB Camera Adapt-
er(*1) and an external power supply device(*2).
*1 You must obtain a genuine Apple Lightning to USB Camera Adapter
separately.
*2 Use a power supply device as described in “Connecting the power” in
this manual.
Adjusting the input sound
Analog audio signals input into this device from mics, guitars, keyboards and
other audio equipment can be converted into digital signals and transmitted
to the computer via USB.
You can use the features of this unit to adjust the digital signals that are sent
to the computer.
In addition, by connecting speakers (through an amplifier if not powered) or
headphones to this unit, you can monitor audio signals that are input to this
unit and output from the computer.
Use the various controls on the front of the unit as necessary while listening
to the input sound.
Example
1
2
3 4
5
Use the GAIN knobs ( ) to adjust the analog input levels of the 3IN1 IN2/
jacks ( ) so that the indicators ( ) above and to the right of the 1PEAK 2
GAIN knobs do not light.
To listen to the monitoring signal using headphones, connect the head-
phones to the jack ( ) and adjust the knob ( ).PHONES 4PHONES 5
NOTE
i If you cannot hear the input sound through the headphones or the LINE
OUT L-R LINE OUT L-R jacks, check the settings of the 4 item on the Set-
tings Panel screen.
i Confirm that the switch is set to O .DIRECT MONITOR N
Troubleshooting
Please read this chapter if you are unable to use the unit properly even after
setting it up following the procedures in this manual.
If you are still unable to resolve your problems please contact the store where
you bought the unit or TEAC customer support with the following informa-
tion about the operating environment and details about the trouble.
Operating environment
o Computer manufacturer :
o Model :
o CPU :
o Memory (RAM) :
o Operating system :
o Applications used :
o Antivirus software :
o Wireless LAN use :
See the contact information on the front of this document.
I cannot install the dedicated software
1. Check the operating system
The operating system being used might not be compatible with the soft-
ware that you are trying to install.
Check the compatible operating system of the software you are trying to
install again.
2. Stop software running in the background
Antivirus software and other software that runs in the background can
prevent installation.
Quit software that runs in the background and try installation again.
The unit is connected, but the computer does not
recognize it.
1. Install the dedicated software
o Install the dedicated software.
Please refer to this manual.“Installing the dedicated software
2. Change the USB port
o This unit cannot be used with USB 1.1. Use a USB 2.0 or USB 3.0 port.
o Do not use a USB hub with this unit. Always connect the unit directly
to a USB port on the computer.
o If the above methods do not resolve the problem, connect the unit to
a different USB port on the computer.
I cannot hear any sound even when audio is played
back on the computer.
Check the status of the unit's connection with the computer.
Moreover, if you make the following settings, sound will be output through
this unit, but no sound will be output by the computer’s speakers or head-
phone jack.
Windows
See the section of in the Ref“Windows Media Player” “Application guide” -
erence Manual, and make settings as necessary for the OS.
Mac
1. Quit all applications and open from the Apple “System Preferences…”
menu.
2. Open .“Sound”
3. On the tab, select .Output “US-1x2”
After completing the setting, restart the computer and check the sound
of playback.
Depending on the application that you are using, you might need to
make additional device settings.
In particular, DAW software operates using audio engines with settings
that are different from the OS settings, so confirm the DAW driver set-
tings first after installing the software for this unit.
Please see the manuals for the applications that you are using for de-
tailed setting procedures.
Sound breaks up or there is noise.
The processing load on the computer causes sound to break up and noise to
occur.
Here are some methods to reduce the load on the computer.
1. A wireless LAN and software running in the background, including an-
tivirus software, regularly put processing loads on the computer, which
can cause sound to break up and other noise.
Stop wireless LAN transmission, antivirus software and other software
running in the background when using this unit.
2. Set the buffer size (latency) in the audio application that you are using or
in this unit's Settings Panel to a larger value. (Windows only)
NOTE
Consult the maker of the audio application that you are using for methods
to reduce its load on your computer.
3. Change the settings of your computer so that they are optimal for audio
processing.
Using Windows
0 Performance Options
1 Open the Control Panel using the procedures for the OS (Windows
10/Windows 8.1/Windows 7).
i In Windows 10, click from the Windows Start “Control Panel
button to open the Control Panel.
Then, click the icon.“System”
i In Windows 8.1, right-click the ordinary Start screen (Metro user
interface screen) and then click .“All apps”
Then, right-click and select .“Computer” “Properties”
i In Windows 7, right-click from the Windows Start “Computer”
button, and select .“Properties”
2 Click “Advanced system settings”.
3 Click “Settings” in the section of the tab “Performance” “Advanced”
of the window.“System Properties”
4 In the Visual Effects” tab of the “Performance Options” window,
select “Adjust for best performance”.
0 Power Options
1 Open the using the procedures for the OS (Windows Control Panel
10/Windows 8.1/Windows 7).
2 Click “Hardware and Sound
3 Click “Power Options”
4 Click “Show Additional Plans”
5 Click on in the “High Performance” Power Options
NOTE
If an item is not shown, select the Show Additional Plansdownward
triangular button.
Using Mac
1 Open “System Preferences…” from the Apple menu, and select “En-
ergy Saver”.
2 Set “Computer sleep” “Never” to .
3 Set “Display sleep” “Never” to .
NOTE
Depending on the Mac OS version and Macintosh computer model, this
setting might not be available.
Support for Bundled DAW Software
TASCAM does not provide end-user support for the bundled DAW Software.
Please check the Help menu of the installed software to find where this sup-
port is available.
Specifications
Ratings
Sampling frequencies : 44.1, 48, 88.2, 96 kHz
Quantization bit depth : 16/24-bit
Analog inputs
IN 1 input
Mic input (Balanced)
Connector : XLR-3-31 equivalent
(1: GND, 2: HOT, 3: COLD)
Input impedance : 2.4kΩ
Rated input level : −65dBu (0.0004Vrms)
(gain knob at MAX)
Rated input level : −8dBu (0.3090Vrms)
(gain knob at MIN)
Maximum input level : +8dBu (1.9467Vrms)
Gain range : 57dB
IN 2 input
LINE/INST input (Balanced/Unbalanced)
Connector : 6.3mm (1/4") standard TRS jacks
(Tip: HOT, Ring: COLD, Sleeve: GND)
Gain range : 45dB
LINE input (Balanced)
( switch set to )LINE INST LINE
Input impedance : 10kΩ
Rated input level : −41dBu(0.0069Vrms)
(gain knob at MAX)
Rated input level : +4dBu(1.228Vrms)
(gain knob at MIN)
Maximum input level : +20dBu(7.75Vrms)
INST input (Unbalanced)
( switch set to )LINE INST INST
Input impedance : 1MΩ or more
Rated input level : −58dBV(0.0013Vrms)
(gain knob at MAX)
Rated input level : −13dBV(0.2239Vrms)
(gain knob at MIN)
Maximum input level : +3dBV(1.4125Vrms)
LINE L/R inputs (Unbalanced)
Connectors : RCA pin jacks
Input impedance : 10kΩ
Maximum input level : +6dBV(1.9953Vrms)
Analog outputs
LINE OUT L-R outputs (Unbalanced)
Connectors : RCA pin jacks
Output impedance : 10
Maximum output level : +6dBV(1.995Vrms)
Headphones output (PHONES)
Connector : 6.3mm (1/4") standard stereo jack
Maximum output : 18 mW + 18 mW or higher
(THD+N 0.1% or less, into 32 Ω load)
Control input/output ratings
USB
Connector : 4-pin USB B-type
Transfer rate : USB 2.0 High Speed (480 Mbps)
DC IN 5V
Connector : USB Micro B type
Audio performance
Mic preamp EIN (equivalent input noise)
−127 dBu or less
(150Ω termination with gain knob at MAX)
Frequency response
IN 1-IN 2 to LINE OUT L-R, PHONES
44.1 kHz, 48 kHz
20 Hz : +0 dB/−0.5 dB (JEITA)
20 kHz : +0 dB/−0.5 dB (JEITA)
20 kHz : +0 dB/−1.0 dB
(PHONES output, JEITA)
88.2 kHz, 96 kHz
20 Hz : +0 dB/−0.5 dB (JEITA)
40 kHz : +0 dB/−1.0 dB (JEITA)
40 kHz : +0 dB/−3.0 dB
(PHONES output, JEITA)
S/N ratio
100 dB or more (22 kHz LPF + A-Weight)
(when LINE input to LINE OUT and gain knob at MIN in standalone
mode*) (JEITA)
Distortion
0.006% or less
(when LINE input to LINE OUT in standalone mode* for 1 kHz sine wave
at rated input and maximum output levels) (JEITA)
Crosstalk
95 dB or more
(when LINE input to LINE OUT in standalone mode* for 1 kHz sine wave)
(JEITA)
* When this unit is turned on and is not connected to a computer by
USB
Computer system requirements
Check the TEAC Global Site ( ) for the latest informahttp://teac-global.com/ -
tion about supported operating systems.
Windows
Supported operating systems
Windows 10 32-bit / Windows 10 64-bit
Windows 8.1 32-bit / Windows 8.1 64-bit
Windows 7 32-bit SP1 or later / Windows 7 64-bit SP1 or later
( Windows 8, Windows Vista and Windows XP are not supported)
Computer hardware requirements
Windows computer with a USB 2.0 port
CPU/processor speed
2 GHz or faster dual core processor (x86)
Memory
2 GB or more
CAUTION
Operation of this unit was confirmed using standard computers that meet
the above requirements.
This does not guarantee operation with all computers that meet the
above requirements.
Even computers that meet the same system requirements might have
processing capabilities that differ according to their settings and other
operating conditions
Mac
Supported operating systems
macOS Sierra (10.12 or later)
OS X El Capitan (10.11 or later)
OS X Yosemite (10.10 or later)
Computer hardware requirements
Mac with a USB 2.0 port
CPU/processor speed
2 GHz or faster dual core processor
Memory
2 GB or more
Apple iOS devices
Apple iOS device running iOS 7 or later
Supported audio drivers
Windows : ASIO2.0, WDM
Mac: Core Audio
iOS device : Core Audio for iPhone
General
Power
Used with a computer
USB bus power
Used with an iOS device
USB power adapter : ( that can supply 5 V and a current of at
least 700 mA)(*1)
External battery pack : ( that can supply 5 V and a current of at
least 700 mA)(*2)
*1 We strongly recommend using TASCAM PS-P520E AC adapter or the
USB power adapter included with the iPad/iPhone. No USB power
adapter is included with an iPod touch. To use it with an iPod touch,
purchase a genuine Apple USB power adapter (that can supply 5 V and
a current of at least 700 mA) separately.
*2 We strongly recommend using a TASCAM BP-6AA external battery
pack. If using another external battery pack or mobile battery, purchase
one that can supply 5 V and a current of at least 700 mA.
Power consumption
2.5W
External dimensions (width × height × depth)
146 × 55 × 120 mm
Weight
623g
Operating temperature range
5–35 °C
0 Illustrations in this manual might differ in part from the actual product.
0 Specifications and external appearance might be changed without notifi-
cation to improve the product.
Trademarks and copyrights
0 TASCAM is a trademark of TEAC CORPORATION, registered in the U.S. and other countries.
0 Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Micro-
soft Corporation in the United States and/or other countries.
0 Apple, Mac, Mac OS, macOS, iPad, iPod, iPod touch, Lightning, App Store and iTunes are trade-
marks of Apple Inc.
0 IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used
under license.
0 ASIO is a trademark of Steinberg Media Technologies GmbH.
0 Other company names, product names and logos in this document are the trademarks or regis-
tered trademarks of their respective owners.
TEAC CORPORATION https://tascam.jp/jp/
1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan Phone: +81-42-356-9143
TEAC AMERICA, INC. http://tascam.com/
1834 Gage Road, Montebello, California 90640 USA Phone: +1-323-726-0303
TEAC UK Ltd. http://tascam.eu/
2 Huxley Road, Surrey Research Park Guildford, GU2 7RE, United Kingdom Phone: +44-8451-302511
TEAC EUROPE GmbH http://tascam.eu/
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany Phone: +49-611-71580
TEAC SALES & TRADING(SHENZHEN) CO., LTD http://tascam.cn/
Room 817, Block A, Hailrun Complex, 6021 Shennan Blvd., Futian District, Shenzhen 518040, China Phone: +86-755-88311561~2
D01313401A
〒206-8530 東京都多摩市落合1-47
この製品の取り扱いなどに関するお問い合わせは
タスカム カスタマーサポート 〒206-8530 東京都多摩市落合1-47
0570-000-809
一般電話・公衆電話からは市内通話料金でご利用いただけます。
受付時間は、10:00 12:00 13:00 17:00 です。
(土・日・祝日・弊社指定休日を除く)
0ナビダイヤルがご利用いただけない場合
電話:042-356-9137 / FAX:042-356-9185
故障・修理や保守についてのお問い合わせは
ティアック修理センター 〒358-0026 埼玉県入間市小谷田858
0570-000-501
一般電話・公衆電話からは市内通話料金でご利用いただけます。
受付時間は、9:30 〜 17:00です。(土・日・祝日・弊社指定休日を除く)
0ナビダイヤルがご利用いただけない場合
電話:04-2901-1033 / FAX:04-2901-1036
所や話番号は、予なく変更る場合がありす。あらかじ
めご了承ください。


Produkt Specifikationer

Mærke: Tascam
Kategori: Ikke kategoriseret
Model: US-1X2
Bredde: 146 mm
Dybde: 120 mm
Højde: 55 mm
Vægt: 623 g
Produktfarve: Black,Grey
Formfaktor: Desktop
Strømforbrug (typisk): 2.5 W
Husmateriale: Metal
Strømkilde: USB
Certificering: RoHS
LED-indikatorer: Ja
USB version: 2.0
Enhedsgrænseflade: USB
Antal USB-porte: 1
Lydindgang: XLR, 6.3mm, 3.5mm
Understøttede Mac-operativsystemer: Mac OS X 10.10 Yosemite,Mac OS X 10.11 El Capitan,Mac OS X 10.12 Sierra
Lydudgang: 6.3mm, 3.5mm
Minimum processor: 2 GHz
Minimum RAM: 2 GB
Understøttede stikprøver: 44.1,48,88.2,96 kHz
Antal analog input: 2
Antal analog output: 2
XLR-indgange: 1
Indbygget mikrofonforforstærker: Ja
6,35 mm (1/4 inch) afbalancerede udgange: 1
Mikrofon forforstærkning indgangsimpedans: -127 ohm (Ω)
48V phantom effekt: Ja

Har du brug for hjælp?

Hvis du har brug for hjælp til Tascam US-1X2 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Tascam Manualer

Tascam

Tascam Porta-02MKII Manual

19 September 2024
Tascam

Tascam DR-10L Pro Manual

23 August 2024
Tascam

Tascam DP-008 Manual

6 August 2024
Tascam

Tascam VL-A4 Manual

6 August 2024
Tascam

Tascam TT-M1 Manual

2 August 2024
Tascam

Tascam MD-02 Manual

1 August 2024
Tascam

Tascam CG-1800 Manual

31 Juli 2024
Tascam

Tascam IF-DA8 Manual

27 Juli 2024
Tascam

Tascam DP-01FX Manual

27 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024